3R system K Series User manual

User Manual
Package Contents and Installation of the parts
How to connect cables
POWERLED:Refertothemanualandinstallitwhileobeying
thepolarities,Ifa4-pinconnectorissupported,
thenconnectittothepowersupply.
HDDLED:Refertothemanualandinstallitwhileobeying
thepolarities.
POWERSW(Switch):Thisswitchhasnopolarity.
Itdoesnʼtmatterwhichplaceyou
connectthistothemainboard.
RESETSW(Switch):Thisswitchhasnopolarity.
Itdoesnʼtmatterwhichplaceyou
connectthistothemainboard.
RESET SWRESET SW
POWER SWPOWER SW
H.D.D LEDH.D.D LED
USBUSB
AUDIOAUDIO
POWER LEDPOWER LED
++
--
++
--
*IncaseofLEDconnector,theterminalwiththe▲markisʻ+ʼ.
USB AUDIO
PaperWasher‒Usethiswith3.5screwsandmainboardsupporter
forelectricalinsulation.
Screw3-UsethistosecureCD-ROM,FDDandvariousPCIslot
cards.
Screw3.5-UsethistosecureMainboardandPSU.
Series
PCSpeaker-Thisisinstalledinmainboardandcalls
theconditionofthesystem.
Mainboardsupporter-Usethisonlywhererequired,andassemble
usingPaperWasher(RedWasher).
Screw(HDD)-UsethistosecureHDD.
:ConnectittotheterminalsontheMainboard.
▶ SpecificationsandimprovementsinthedesignofourPCcasearesubject
tochangewithoutanypriornotice.
▶*Warrantyvoidswhendamageiscausedbyuserʼsabuse,misuseor
byanaturaldisaster.
*Warrantyvoidswhendamageiscausedbymodifyingtheproductor
byusingtheproductinimproperapplication.
▶ ForthedetailedA/Sandsupport,pleasevisitourwebsite.
(http://www.3rsys.com)
TEL:82220272555Fax:82220272088e-mail:[email protected]
메인보드
*HowtoassembletheScrew:Besureto
installthepaperwasherbetween
theMainboardandtheScrew(3.5)
topreventashortcircuit.

Functions
*1-channeltemperaturemonitor
*1-channelfanspeedcontrol
*Autofanspeedcontrol
▶40℃:Low
50℃:Mid
60℃:High
*ImmediatevisualindicationofFan/HDDoperation
*On-boardPower&ResetSwitch
Buttons
*LCDRESET:Resetstodefaultsettings
*LCDSELECT:SwitchesfanspeedfromLowtoMidtoHigh
*POWERSW:SystemPowerSwitch
*RESETSW:SystemResetSwitch
Functions
*1-channeltemperaturemonitor
*2-channelfanspeedcontrol
*6-levelfanspeedcontrol(manual)
*Fanspeedstoragefunction
*Autofanspeedcontrol
▶40℃:Low
50℃:Mid
60℃:High
*ImmediatevisualindicationofFan/HDDoperation
*Displayssystemrunningtime
Buttons
*LCDRESET:Resetstodefaultsettings
*MODE:Switchesfancontrolchannels
*UP:Increasesfanspeed(level1→ level6→Auto)
*DOWN:Decreasesfanspeed(level6→level1→Auto)
ThermalProbe:Placethissensortotheproperplaceto
measurethetemperatureinsidethecase.
FanPowerConnector:Connectthistothe3-pinFan
providedinthecase.
(OnlyavailablefortheLCDproduct)
RESET
LCD RESET
MODE UP
DOWN
LCD SELECT
POWER RESET
How to connect cables How to connect cables
4-pinPowerSupplyConnector:ConnectthistoPSU.
(OnlyavailablefortheLCDproduct)
*DonotplacethesensoronCPUcore,orHeatsink.
*IfthereisthegapbetweencoolerbaseandCPU
corebecauseofthewireofthesensor,CPUmay
bedamaged.
*Ifthereiscoolerguide,thecableofthesensor
shouldbereplacedunderthecoolerguideto
avoidthedisconnection.