3T-Components 3T-MOTORS 3T45-20RNH User manual

Motor type 3T45-RNH
(For shafts from 60 mm)
3T45-20RNH
3T45-40RNH
www.3t-components.de |WEEE-Reg.-Nr.: DE 77028333
Smart Home Ready with everHome
Control via smart phone, tablet, PC or via
voice commands with Alexa or Google Assistant
INTELLIGENT
DRIVES &
CONTROLS
FOR SHUTTERS
AND AWNINGS
INSTALLATION &
OPERATING INSTRUCTIONS
Instructions and notes for installation and operation
3T-MOTORS Radio shutter / awning motors
with mechanical limit switches + emergency manual operation
Attention:
It is important for the safety of persons
to follow these instructions.
Keep these instructions for future reference.

2
TABLE OF CONTENTS
3T-MOTORS Radio shutter motors / Radio awning motors with mechanical limit switches
Guideline / Determine torque Page 3
Safety instructions Page 4
Function overview
Scope of delivery Page 5
Technical data Page 5
Manual emergency operation Page 6
Installation notes Page 6
Installation instructions
Installation radio shutter motor Page 7 – 10
•Installation situation Page 7
•1) Prepare power connection Page 7
•2) Remove shutter shaft Page 8
•3) Prepare motor for installation Page 8
•4) Mount bearings Page 8
•5) Mount motor with shaft unit Page 8 – 9
•6) Shutter motor wiring Page 9
•7) Programming radio transmitter Page 9
•8) Setting the end positions Page 10 – 11
Installation radio awning motor Page 12 – 14
•1) Preparation Page 12
•2) Prepare motor for installation Page 12
•3) Mounting radio awning motor Page 12 – 13
•4) Radio awning motor wiring Page 13
•5) Programming radio transmitter Page 13
•6) Setting the end positions Page 14
Programming radio transmitter
Pairing handheld transmitter Page 15
Changing the direction of rotation of the radio motor Page 15
Pairing another handheld transmitter Page 15
Delete handheld transmitter Page 16
Shutter & blind operating mode Page 16
Troubleshooting
What to do when ... Page 17
Hotline
06732 600 0369
3T-MOTORS Radio tubular motors | Table of contents
CONTACT
3T-Components GmbH & Co. KG
Bahnhofstr. 34
55578 Wallertheim
Email: [e-mail]
Tel: [phone]
Fax: [phone]
Opening hours:
Monday – Friday
8:00 – 17:00
www.3t-components.de
Learn more about us:
© Copyright notice
All contents of these instructions, in particular texts, photographs and graphics,
are protected by copyright. Unless expressly indicated otherwise, the copyright
is held by 3T-Components GmbH & Co. KG. Please ask us if you wish to use
the contents of this document.

3
GUIDELINE
With this guide, you can determine the ideal torque in Newton meters (Nm) for the shutter motor.
DETERMINE WEIGHT ROLLER SHUTTER
1.) Determine roller shutter area
(Height + 150 mm) x Width = Roller shutter area (m²)
2.) Determine weight roller shutter material
Take approximate weights per m² of roller shutter area
from the table.
3.) Determine weight roller shutter
Roller shutter area (m²) x weight roller shutter material (m²)
4.) Calculate required traction force
Friction losses must be taken into account
(rail guidance) of approx. 10%!
Roller shutter area (m²) x Weight roller shutter material (m²) = Weight roller shutter (kg) + 10% Friction losses = Required traction force (kg)
Example:
PVC-Roller shutter area 3,00 m² x Weight roller shutter material 5 kg = 15 kg Weight roller shutter + 10% Friction losses = 16,5 kg Required traction force
Material
PVC
Aluminum Light
Aluminum Heavy
Steel
Wood
kg /m²
5
6
9
11
11
DETERMINE SHUTTER MOTOR TORQUE
100
90
80
70
60
50
40
010 20 30 40 50 60 70 80 90 100
515 25 35 45 55 65 75 85 95
10 Nm 13 Nm 30 Nm 40 Nm 50 Nm
Traction force (kg)
ØShaft (mm)
Torque (Nm): 20 Nm
Roller shutter box
Bottom edge
Roller shutter box
Window sill
Height
Width
3T-MOTORS Radio tubular motors | Guideline

4
3T-MOTORS Radio tubular motors | Safety instructions
GENERAL SAFETY INSTRUCTIONS
IMPROPER USE
PROPER USE
•WARNING: Important safety instructions.
Follow all instructions as incorrect installation may result in serious injury.
•WARNING: The drive must be disconnected from the power source during cleaning, maintenance and replacement of parts.
•Danger to life from electric shock when working on electrical equipment.
• The electrical connection, installation and commissioning of the receiver may only be carried out by qualied personnel.
•Before installing the drive, remove all unnecessary cables and disable all devices,
that are not required for operation with power.
•The relevant regulations and guidelines must be followed without fail, to avoid damage to persons and objects.
•Observe safety instructions according to EN 60 335-2-97: The power supply cable of the drives must be laid internally.
•Installation according to DIN 18073: The roller shutter box cover must be easily accessible and removable.
•Installation according to EN 60335: Only switches / pushbuttons / switching devices with a minimum contact opening
of 3 mm may be used, furthermore the up and down direction must be interlocked against each other.
•When installing in damp rooms, observe regulations (VDE 0100, part 701 and 702).
•Do not use defective devices: Never use defective equipment.
Periodically inspect the equipment for imbalance and signs of wear or damage to cables and suspension springs.
Do not use equipment if repair or touch-up is necessary.
There is a risk of personal injury and property damage due to electric shock or short circuit.
•Retain the instructions for future reference.
•Use tubular motors only for automating shutters.
•Only use original components and original accessories from the manufacturer.
•The mains connection cable of the drives must be laid internally in the empty conduit up to the junction box.
The local electrical regulations must be observed.
•For the electrical connection of the tubular motors, a 230 V / 50 Hz
power connection with fuse must be available at the installation site.
•Inspect the installation frequently for imbalance and signs of wear or damage to cables and springs.
Do not use if repairs or adjustments are required.
Please read these important safety instructions before commissioning!
Incorrect installation can cause serious personal injury and damage to property.
The warranty claim expires in case of non-observance of this user information with all contained notes and regulations.
In case of non-observance of these instructions, the manufacturer or supplier shall not be liable for any personal injury or property damage incurred.
SAFETY INSTRUCTIONS
This symbol indicates danger due to electrical energy.
Danger to persons and objects may arise if the
associated information is not observed!
This symbol indicates information about general danger.
Non-observance can mean danger to
persons and objects!
This symbol indicates important information that can
ensure safe and proper use of the device.
•Persons are to be instructed with the correct operation of the tubular motor.
•The roller shutter movement must be monitored in order not to endanger persons.
•Do not allow children to play with motor controls.
•Store the handheld transmitter in such a way that unintentional operation is prevented (e.g. by children playing).
•The device can be used by children aged 8 years and above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge, if they have been given supervision and instruction concerning use
of the appliance in a safe way and are aware of the hazards involved.
•Children are not allowed to play with the equipment.
•If the power supply cord of this device is damaged, it must be replaced by the manufacturer or its customer service
or a similarly qualied person to prevent hazards.

5
SCOPE OF DELIVERY – MOTOR TYPE 3T45-RNH
1Motor
2Limit switch adapter
3Shaft adapter
4Connection cable 3 meters
6Universal bearing & cotter pin
8Securing bracket
5Adjustment pin
8Emergency hand crank eyelet
9Manual
2 31
75 6 9
Ø60 mm
8-sided Shafts from 60 mm
APPLICATION
Motorized radio shutters
& awnings
Limit switch
FUNCTION OVERVIEW – MOTOR TYPE 3T45-RNH
Optional adapter sets + accessories
you will nd in our store under mounting accessories
8
4
SUITABLE FOR
Round shafts with outer diameter:
63 mm / 70 mm / 78 mm / 85 mm
Ø
Motor type
Torque (Nm)
Traction power (kg)
Max. Projection (m)
Max. PVC shutter area (m²)
Max. ALU shutter area (m²)
Power (W)
Standby consumption (W)
Turn Speed (U/min)
Limit switch capacity (min)
Operating voltage (V AC)
L1 Total motor length (mm)
L2 Installation length (mm)
Connection line (m)
Max. Runtime (min)
Protection class
EAN
3T45-40RNH
40
80
Suitable for folding awnings with up to 5 m projection (with 2 folding arms)
11
9,5
198
2
15
22
230 V / 50 Hz
781
751
3
4
IP44
4260601760499
Technical data
3T45-20RNH
20
40
–
6
4,7
145
2
15
22
230 V / 50 Hz
751
721
3
4
IP44
4260601761359
FUNCTION OVERVIEW
3T-MOTORS Radio tubular motors | Function overview