9dot GIGASYNC V2 User manual

1
MANUAL GIGASYNC V2
VER. 2 REV. 1
1. GIGASYNC pag. 2
1.1. Base Unit pag. 2
how it looks pag. 2
block diagram pag. 3
voltage range pag. 3
connectors scheme pag. 4
ethernet pinout, sync-in and sync-out pag. 4
LED legend pag. 4
OPT functions pag. 4
1.2. Cartridges pag. 5
how they look pag. 5
comparative table pag. 6
LED legend pag. 6
9.KEY pag. 6
1.3. Installation pag. 7
1.4. Software update pag. 8
1.5. WEB Interface pag. 9
1.6. Command Line Interface pag. 13

2
MANUAL GIGASYNC V2
VER. 2 REV. 1
1.
GIGASYNC
GigaSync is designed to power devices by Power Over Ethernet standard or directly by bipolar Terminals.
It consists of a Base Unit which can host up to three Cartridge expansions. The Base Unit holds the
control and main interface systems while Cartridges specify the power methods: Power Over Ethernet
or Terminals.
1.1. Base Unit
On the front there are visible the 3 LEDs SYNC, STATUS and ALARM and the OPT function button. The
Base Unit can accommodate up to three cartridges in the Cartridge Slots, simply removing the metal
cover and inserting the cartridge. No fixing screws are required.
On the back there are power input terminals of the Base Unit and their cartridges. Each power input is
independent, insulated and equipped with reverse polarity protection. The voltage range is 18-60 Volts.
The Base Unit can also be powered by PoE IEEE 802.3af standard via the Ethernet. There are also
ports for the SYNC-IN and SYNC-OUT (respectively employable to acquire or replicate the sync pulse)
and the connector for the GPS antenna. For a correct operation of the surge protectors, it is necessary
to connect the ground terminal GND.
OPTION BUTTON
SYNC OUT / SYNC IN
CARTRIDGE SLOTS
LEDs
GPS ANTENNA CONNECTOR
CARTRIDGE REDUNDANT POWER CONNECTORS
MAIN POWER
ETHERNET PORT
POWER PRESENCE LEDs
GND

3
MANUAL GIGASYNC V2
VER. 2 REV. 1
GigaSync block diagram
The block diagram highlights the presence of three major structures: a CPU ensures the correct
operation of all the basic electronics operation and carries out the voltage and current measurements
(•), the other CPU manages the User Interface (•), and finally the power components isolated from the
rest of the logic (•). The four power INPUTs, each applicable via two redundant connectors, are isolated
from each other and do not apply any conversion to the voltage applied to the cartridges, in this way it
is possible to simultaneously connect different voltages and different polarities (e.g.: INPUT 1 à48V,
INPUT 2 à24V, INPUT 3 à-48V).
Voltage range, power consumption and maximum load
Input Voltage
Self Consumption
Max Load
PoE
36-57 V DC
4.5W
na
MAIN INPUT
18-60 V DC
4.5W
na
INPUT 1
18-60 V DC
0.3W
600W
INPUT 2
18-60 V DC
0.3W
600W
INPUT 3
18-60 V DC
0.3W
600W
The cartridges power INPUTs are equipped with reverse polarity protection: in case of wrong connection,
the corresponding cartridge is not receiving power.
The two CPUs are powered by an isolated converter. In this way it is guaranteed maximum immunity
against electrical faults on the supply lines of the cartridges.
* Functions available only on PoE-CS Cartridge.
** Functions available only on PoE and PoE-CS Cartridge.
MAIN INPUT POWER
INPUT POWER 1
INPUT POWER 2
INPUT POWER 3
isolated
DCDC CONVERTER
CPU
UI
CPU
HW
SYNC
Inverse Polarity
PROTECTION
Inverse Polarity
PROTECTION
Inverse Polarity
PROTECTION
VOLTAGE & LOAD
MEASUREMENT
VOLTAGE & LOAD
MEASUREMENT
VOLTAGE & LOAD
MEASUREMENT
ON / OFF
PROTECTION
ON / OFF
PROTECTION
ON / OFF
PROTECTION
SYNC PULSE
GENERATION *
SYNC PULSE
GENERATION *
SYNC PULSE
GENERATION *
KEY DETECT **
OUTPUT PORTS
Wifi
KEY DETECT **
OUTPUT PORTS
OUTPUT PORTS
KEY DETECT **
Cartridge 1
Cartridge 2
Cartridge 3
ETH PoE
DUAL CPU
SYNC IN SYNC OUT
LEDs OPT
GPS
LED
LED
LED

4
MANUAL GIGASYNC V2
VER. 2 REV. 1
INPUT Ethernet PoE 802.3af
RJ45 Pin
100Base-T
Power
1
TX
DC +
2
TX
DC +
3
RX
DC -
4
n / c
DC +
5
n / c
DC +
6
RX
DC -
7
n / c
DC -
8
n / c
DC -
Sync IN
RJ11 Pin
Sync
Voltage Range
1
RX +
5 - 12V V DC
2
n / c
3
n / c
4
n / c
5V (UGPS power)
5
GND
6
GND
Sync OUT
RJ11 Pin
Sync
Voltage Range
1
TX +
DC 5V
2
n / c
3
n / c
4
n / c
5
GND
6
GND
Legend LED on the front panel
LED
Color
Description
SYNC
flashing green 500ms
flashing green 200ms
alternating with the LED ALARM: boot phase not complete
pulse presence on the selected Sync synchronization
(GPS or SYNC IN)
STATUS
blue
device correctly powered
ALARM
flashing red 500ms
when pressing the OPT button
alternating with the LED SYNC: boot phase not complete
Button functions OPT
OPT
long press
Description
WiFi on / off
ALARM LED starts flashing after
about 5 seconds off
switching on or off WiFi interface
RESET
after about 30 seconds turns the
LED STATUS
configuration reset and restore the factory settings

5
MANUAL GIGASYNC V2
VER. 2 REV. 1
1.2. Cartridges
There are 2 types of cartridges that are used to power various devices both via terminal connectors and
via Power over Ethernet injection. The PoE-CS cartridges are also able to inject the sync pulse. On each
port of all the cartridges a hardware protection against short circuit is active and there are dual stages
TVS and GDT surge arresters on each line.
GS-G-PoE
|
GS-G-PoE-CS
LAN Ports
GS-G-TER
PoE Ports
STATUS LEDs
KEY SLOTS
MAIN CONNECTOR
MAIN CONNECTOR
FRONT VIEW
SIDE VIEW
BACK VIEW
BACK VIEW
SIDE VIEW
FRONT VIEW
Terminals
STATUS LEDs

6
MANUAL GIGASYNC V2
VER. 2 REV. 1
Part Number
GS-G-PoE
GS-G-PoE-CS
GS-G-TER
Type
PoE
PoE
Terminal
Ports
4
4
4
Connector Type
Shielded RJ45
Shielded RJ45
Terminal, Ø 4mm
Pinout
configurable 9.KEY
configurable 9.KEY
bipolar fixed
Max Peak Load
3A per port
3A per port
3A per port
Max Continuous Load
1.5A per port
1.5A per port
1.5A per port
Voltage Range
18-60V DC
18-60V DC
18-60V DC
Hot Swap1
•
•
•
Short Circuit Protection
•
•
•
Over Voltage Protection
> 150V
> 150V
> 150V
Impulse Discharge Current
2000 A, 8/20 | 100 A, 8/20 | 10 A, 10/1000 ĩS | 2 A, 50 Hz, 1 sec
Gigabit Transformer
•
•
n / a
Canopy Sync
•
n / a
Cambium Sync
•
n / a
Legend LED on the cartridges
PoE
PoE-CS
TER
Color
Description
•
•
•
flashing white on all ports
lack of feeding on the cartridge connector
•
•
•
flashing white on a port
blink identification
•
•
•
red flashing
disabled port
•
•
red
9.KEY inserted incorrectly or invalid
•
•
flashing purple
9.KEY missing
•
•
•
violet
power cycle (10 seconds)
•
•
•
green
enabled port
•
light blue
port enabled with Canopy Sync synchronization
•
blue
port enabled with Cambium Sync synchronization
Part Number
GS-K-9.S
GS-K-AB
GS-KB
GS-K-BRP
Name on KEY
9.SYNC
A + B
B
BRP
PoE Mode
A + B reverse pol.
A + B
B
B reverse pol.
1.2 wires
DC +
DC +
3.6 wires
DC -
DC -
4.5 wires
DC -
DC +
DC +
DC -
7.8 wires
DC +
DC -
DC -
DC +
COMPATIBILITY
Cambium 450m
•
Cambium 450i
•
•
Cambium 450
•
IEEE 802.3af / at
•
10 / 100Base-T PoE
•
1000Base-T PoE
•
•
Intracom / SIAE
•
•
Mikrotik / Ubiquiti
•
•
1
The cartridges can be inserted and removed from the Base Unit even if the system is powered and operational. It is preferable
to connect the devices to be powered after the insertion of the cartridge to ensure proper calibration of the readings.

7
MANUAL GIGASYNC V2
VER. 2 REV. 1
1.3. Installation
GigaSync is designed for installation in 19" rack cabinet, however, the fastening tabs can be rotated 90°
for wall mounting.
For a correct functioning of the surge arresters it is indispensable to connect to ground the rack cabinet
and connect the grounding terminal on the back.
To install the cartridges just remove the metal plate placed at slot cover on the Base Unit and insert the
cartridge making sure it entirely fits.
No fixing screws for the cartridges are required, the connector provides sufficient strength to prevent
that they do not inadvertently fall. To remove the cartridge pull hard the handle.
CARTRIDGE SLOTS

8
MANUAL GIGASYNC V2
VER. 2 REV. 1
1.4. Software update
The GigaSync software versions follow the schema: [version]. [release]. [fix].
The version covers the entire software platform, the release introduces new features, fix corrects or
optimizes existing functionality.
1.4.1. File upload
Connect to GigaSync through FTP in port 21 with TLS support, using the access credentials to GigaSync
(ex .: admin, password) or upload the update file in the Controller Actions / System Update of the web
interface.
1.4.2. Upload
Upload the update file update_ [version number] .9dt.
1.4.3. Update
Using your login credentials to GigaSync (ex .: admin, password), connect via SSH and run the command
system / upgrade / upgrade or via web interface in the section Actions Controller / System Update.
GigaSync automatically validate the update installation package.
During the update procedure, GigaSync continues to power the devices connected to it and continues
to inject the sync pulse. When the red LED stops flashing, the software update is complete.

9
MANUAL GIGASYNC V2
VER. 2 REV. 1
1.5. WEB Interface
GigaSync’s WEB interface is specially designed to facilitate access from mobile devices. It is possible to
monitor in real time the parameters of voltage and load applied and send on/off command, power-cycle
and sync. Interpretation of the data is made even easier by the possibility to comment on the ports of
the connected cartridges.
A simple caption red / green / gray color, allows an immediate identification of the ports in alarm and
disabled state.
The graphs of voltage and load values are real time updated and turn yellow and red in the presence of
deviations from the mean.
Figure 1 - LOGIN PAGE
IP: 192.168.9.1
Login: admin
Password: password
Figure 2 - MAIN PAGE
Once the login, the main screen is divided into two
blocks.
The gray part concerns the Base Unit, the part below lists
the connected cartridges.
The line of each cartridge can be expanded to display
information about the ports and to send commands.
The load applied to each port is indicated by a color so
as to make it readily apparent which are the devices with
greater consumption and closer to the maximum load
limit.
GREEN, <50%
YELLOW, 50% - 75%
RED,> 75%

10
MANUAL GIGASYNC V2
VER. 2 REV. 1
Figure 3 - MAIN MENU
In the main menu displays the temperature and voltage graphs, the
presence of power via terminals ( •) And / Or via PoE ( ).
INFO tab contains information on uptime, GPS software version
data.
In NETWORK tab it is possible to change the network settings, turn
on WiFi and enable NAT that enables surfing the Internet when
connected to WiFi GigaSync (if the GigaSync network parameters
allow it).
In SYNC tab it is possible to select the sync source whose
presence is indicated by the green circle. It is possible also to
enable the Sync Cascade and feed the Sync-IN port for the direct
supply of a uGPS.
LOG tab displays the events.
Figure 4 - PROFILE SETTINGS
The menu allows to change the admin user's password
and log out.