Altronics S9921A User manual

S9921A –Instruction Manual
0
Contents
Note.............................................................................................................................1
Basic Operation .........................................................................................................3
1. Add IPCam to NVR ............................................................................................3
2. IPC parameters synchronization.....................................................................11
3. System Login................................................................................................13
4. Main Menu....................................................................................................14
5. Preview set...................................................................................................15
6. Record Config..............................................................................................16
7. Motion Detect...............................................................................................17
8. Playback........................................................................................................21
9. Network setup..............................................................................................24
10. PTZ control.................................................................................................25
11. Restore factory settings ..............................................................................29
IE/CMS/Mobile Connection....................................................................................30
1.IE connection...................................................................................................30
2.CMS client connection.....................................................................................31
3.Mobile connection ..........................................................................................31

S9921A –Instruction Manual
1
Note
Please read this manual carefully before installing and using the machine
to ensure your interests.
Do not use the power that does not match the power adapter.
Make sure to connect the ground to avoid thunder damage to the main
chip before using the product.
Do not use the machine where it is likely to be exposed to rain or humid.
Do not install the machine in dusty places, and avoid mechanical vibration
and shock.
Keep the machine in a well-ventilated place and avoid direct sunlight and
high-temperature.
If possible, choose a dedicated DVR hard drive to meet a long time, a
large amount of data read and write.
Please buy a hard drive from the formal channels to ensure quality.
Disconnect the power of each device to avoid live-swappable before
connection with other devices.
if there are objects or liquid accidentally fall into the machine, immediately
disconnect the power supply, and ask qualified technicians test before
using it again.
If the machine is not used for a long time, please completely take off the
power and keep the power cord away from the power outlet.
This machine is a precision machine and the user cannot repair it. Please
contact qualified technical or distributors.
After you open the case, you should check:
In addition to check whether there are obvious signs of damage, please
check if the data line with front panel, power supply and the connection to the
motherboard is loose.

S9921A –Instruction Manual
2
II. Connection
For initial use, please install the hard drive.
①Connect hard disk

S9921A –Instruction Manual
3
Connect VGA Output
Connect the network cable
Basic Operation
1. Add IP Cam to NVR
(1)To add IP cameras to NVR, please go to "Main Menu -- Add IPC" . NVR
will search the IP cameras in LAN automatically.（Click “Update IP”to sync the IP
of IPC when NVR and IPC are in the same network segment）.Click “ADD”to add

S9921A –Instruction Manual
4
the device to the channel list below. Click “OK”to Save after adding devices. You
can click "Modify" to change the configuration of the IP cam.
For example, when you setup an IPC with ONVIF protocol, the IP Address
should be in the same network segment with NVR, port uses the searched port,
protocol is ONVIF, resolution/user name/password should be the same as that on
IPC.

S9921A –Instruction Manual
5
(2)Right click on the preview interface, and click “Add IPC”.
If you click “add IPC”next, NVR will show the IP cameras searched
automatically in LAN. Click “Add”, the selected IPC will be added to current channel.

S9921A –Instruction Manual
6
If you click “Add All IPC”, please select a protocol, and then NVR will
automatically search and add IP cameras supported this protocol in LAN to all
channels.

S9921A –Instruction Manual
7
(3)Click “+”in the middle of the channel, NVR will show the IP cameras
searched automatically in LAN. Click “Add”, the selected IPC will be added to current
channel.

S9921A –Instruction Manual
8
(4) Connect NVR via IE, click “setup--Device setting--System maintenance--channel
mode setup”. Select channel and device, and then click “Apply”.
Fill in the IPC info on the right and click “Update”. Click “OK”to exit channel mode.

S9921A –Instruction Manual
9
You will see the IPC when you return to the preview interface.

S9921A –Instruction Manual
10

S9921A –Instruction Manual
11
2. IPC parameters synchronization
1. IP sync. Please go to "Main Menu -- Add IPC" . NVR will search the IP cameras in
LAN automatically. Click “Update IP”to sync the IP of IPC when NVR and IPC are
in the same network segment.
2. Color setting sync. Right click on the preview channel and choose “Color
setting”. NVR will sync the color setting with IPC when “Sync color set”is
enabled.

S9921A –Instruction Manual
12
3.
(1) Encode config sync. Go to “Main menu--Encode config”. NVR will sync the
encode parameters with IPC when “Sync encode set”is enabled.

S9921A –Instruction Manual
13
3. System Login
When the DVR boots up, the user must login and the system provides the
corresponding functions with the user purview. There is one user settings. The
name is Admin and has no password. Admin is the super user purview. User
Admin’s password can be revised, while their permissions can’t be revised.
Password protection: If the password is continuous wrong ten
times, the account will be locked. (Through reboot or after half an hour,
the account will be unlocked automatically).

S9921A –Instruction Manual
14
For your system security, please modify your password after first
login.
4. Main Menu
When you login, the system main menu is shown as below
Main Menu
1. Switch page: 3methods to switch pages in main menu: click the color picture on
the sides of the main page; press the left key and slide left or right; click the dots
below the main page.
2. Change background: click to change the background color.
3. Edit: click to enter edit mode. Items on first page are fixed. Drag items in
the main page area to change their positions. Drag items outside the main page

S9921A –Instruction Manual
15
area or click to hide the items.Drag items to the main page area or click
to show them.
4. Shutdown：click shutdown the main menu.
5. Preview set
Right click on the preview interface to enter “Preview set”.According to the
situation, you can choose the main stream or sub-stream in the preview of each
IPC channel.
1. If the actual screen-split number is bigger than the setup value, then it
display sub-stream
2. If the actual screen-split number is smaller than the setup value, and it do
not exceed the decoding capabilities, then it display main stream; if it is
beyond decoding capabilities, then it shows "resources lack"

S9921A –Instruction Manual
16
6. Record Config
Set the recording parameters in the surveillance channel. The system is
set 24 hours consecutive recording in the first startup. You can enter [main
menu]>[record mode] to set.
Record Config
【CAM】Choose the corresponding channel number to set the channel.
Choose the all option to set the entire channels.
【PreRecord】Record 1-30 seconds before the action. (time length is decided
by the code stream)

S9921A –Instruction Manual
17
【Mode】Set video state: general，detect，alarm，event，stop.
General: Perform the regular recording in the set time section.
Detect: Trigger the “motion detect”, “camera mask” or “video loss” signal.
When above alarm is set as opening recording, the “detection recording” state
is on.
Alarm: Trigger the external alarm signal in the set time section. When above
alarm is set as opening recording, the “detection recording” state is on.
Event: All record except general record
Stop: The according channel stops recording in the set time section
【Period】Set the time section of common recording, The recording will start
only in the set range. First select one of the record mode, then click the left
key or drag to select the period.
【Copy to】copy the current channel settings to other channels.
7. Motion Detect
When system detects the motion signal that reaches the set sensitivity,
the motion detect alarm is on and the linkage function is turned on.

S9921A –Instruction Manual
18
Motion Detect
【CAM】Choose the set motion detect channel.
【Enable】means that the motion detect function is on.
【Sensitivity】Choose in the six options according to the sensitivity.
【Region】Click setup and enter the set area. The area is divided into
PAL22X18.. Yellow block means the dynamic detect defensive area. Black
block means the unfenced area. You can set the area as followed, Drag the
mouse and draw the area.

S9921A –Instruction Manual
19
Motion Detect Region
【Period】Trigger the motion detect signal in the set time section.Click the left
key of mouse or drag on the time blocks to select period .Yellow means the
set valid.
set the time section