A/DA PLATINUM II User manual
PLATINUM II
ZONE CONTROL SYSTEM
MOTION SENSOR/TIMER
2
TABLE OF CONTENTS
3
1
1.Precautions 2
2.EnvironmentalInformation 2
3.ComponentsSupplied-SIPSKit 3
4.ComponentsSupplied-TimerKit 3
5.ComponentsSupplied-MotionSensorKit 4
6.MountingtheTimer 4
7.WiringDiagram 6
8.MultipleTimersusingSIPS 7
9.MultipleTimerConfiguration 8
10.MountingtheMotionSensor 10
11.MultipleMotionSensorsusingSIPS 11
12.MotionSensorConfiguration 12
13.MotionSensorwithAdd-OnTimerConfiguration 15
14.MotionSensorConfiguration-NoZones 16
15.MotionSensorwithAdd-OnTimerConfiguration
-NoZones 17
16.SystemSetUp 18
17.TimerFunction 20
18.MotionSensorFunction 20
19.Faults 21
20.Diagnostics 23
21.Warranty 24
22.Notes 24
1
PLATINUM II
2
TABLE OF CONTENTS
3
1
1.Precautions 2
2.EnvironmentalInformation 2
3.ComponentsSupplied-SIPSKit 3
4.ComponentsSupplied-TimerKit 3
5.ComponentsSupplied-MotionSensorKit 4
6.MountingtheTimer 4
7.WiringDiagram 6
8.MultipleTimersusingSIPS 7
9.MultipleTimerConfiguration 8
10.MountingtheMotionSensor 10
11.MultipleMotionSensorsusingSIPS 11
12.MotionSensorConfiguration 12
13.MotionSensorwithAdd-OnTimerConfiguration 15
14.MotionSensorConfiguration-NoZones 16
15.MotionSensorwithAdd-OnTimerConfiguration
-NoZones 17
16.SystemSetUp 18
17.TimerFunction 20
18.MotionSensorFunction 20
19.Faults 21
20.Diagnostics 23
21.Warranty 24
22.Notes 24
1
PLATINUM II
3. Components Supplied - SIPS Kit
SIPS01 Control Box A/C Link Cable (9m)
240V AC Power Cord Link Cable (15m)
1 x Instruction Manual
4. Components Supplied - Timer Kit
TM01 Timer A/C Link Cable (9m)
2 x Fixing Kit
1 x Instruction Manual
1. Precautions
Refer to these installation instructions before commencing the installation or
service of this product.
WARNING
This product should be installed and set up by qualified personnel.
To reduce the risk of fire, electric shock or product damage:
DO NOT expose to rain or moisture of any kind
DO NOT place articles filled with water on or near this appliance
DO NOT remove covers – there are no serviceable part inside
DO use only genuine Air Diffusion Agencies components
Ensure all electrical connections are made before connecting power to the
Control Box.
Installation set up changes should only be attempted by qualified personnel.
2. Environmental Information
This product (including packaging) is manufactured from fully recyclable
components. Please dispose of in an appropriate manner.
This appliance is not to be used by persons, including children with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction.
RECYCLE
PRECAUTIONS
PLATINUM II
23
COMPONENTS SUPPLIED
MOTION SENSOR/TIMER SET UP
3. Components Supplied - SIPS Kit
SIPS01 Control Box A/C Link Cable (9m)
240V AC Power Cord Link Cable (15m)
1 x Instruction Manual
4. Components Supplied - Timer Kit
TM01 Timer A/C Link Cable (9m)
2 x Fixing Kit
1 x Instruction Manual
1. Precautions
Refer to these installation instructions before commencing the installation or
service of this product.
WARNING
This product should be installed and set up by qualified personnel.
To reduce the risk of fire, electric shock or product damage:
DO NOT expose to rain or moisture of any kind
DO NOT place articles filled with water on or near this appliance
DO NOT remove covers – there are no serviceable part inside
DO use only genuine Air Diffusion Agencies components
Ensure all electrical connections are made before connecting power to the
Control Box.
Installation set up changes should only be attempted by qualified personnel.
2. Environmental Information
This product (including packaging) is manufactured from fully recyclable
components. Please dispose of in an appropriate manner.
This appliance is not to be used by persons, including children with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction.
RECYCLE
PRECAUTIONS
PLATINUM II
23
COMPONENTS SUPPLIED
MOTION SENSOR/TIMER SET UP
PLATINUM II
45
MOTION SENSOR/TIMER SET UP
MOUNTING THE TIMER MOUNTING THE TIMER
5. Components Supplied - Motion Sensor Kit
MS01 Motion Sensor Cable (9m)
2 x Fixing Kit
1 x Instruction Manual
6. Mounting the Timer
NOTE: To use the Timer with an A/C, the A/C must have external control input.
Power is supplied from the A/C indoor unit - refer to A/C unit wiring diagram.
Once installed, the indoor unit must be set to enable external control operation -
the method will vary from model to model.
DO NOT mount Timer in direct sunlight.
ŸPlug in supplied A/C Link Cable to the Timer, then fix Front Plate to the wall.
ŸFront Plate can be attached to the wall using supplied fixings or a standard wall
switch bracket.
ŸSet time period by adjusting dip switches, then clip on Cover Plate, ensuring
clips fully engage.
84mm
1 2 3 4
45mm
30mm
NOTE: Ensure wall behind Front
Plate in this area is completely clear
Any other configuration
will default to 2 hrs
1 2 3 4
2 hrs 1 2 3 4
4 hrs
1 2 3 4
6 hrs 1 2 3 4
8 hrs
Front Plate
Mounting Screw
Cover Plate
To A/C
To remove Cover Plate once assembled onto the wall, use a small flat head
screwdriver in the locations shown to pry Cover Plate off of the Front Plate.
1
2
PLATINUM II
45
MOTION SENSOR/TIMER SET UP
MOUNTING THE TIMER MOUNTING THE TIMER
5. Components Supplied - Motion Sensor Kit
MS01 Motion Sensor Cable (9m)
2 x Fixing Kit
1 x Instruction Manual
6. Mounting the Timer
NOTE: To use the Timer with an A/C, the A/C must have external control input.
Power is supplied from the A/C indoor unit - refer to A/C unit wiring diagram.
Once installed, the indoor unit must be set to enable external control operation -
the method will vary from model to model.
DO NOT mount Timer in direct sunlight.
ŸPlug in supplied A/C Link Cable to the Timer, then fix Front Plate to the wall.
ŸFront Plate can be attached to the wall using supplied fixings or a standard wall
switch bracket.
ŸSet time period by adjusting dip switches, then clip on Cover Plate, ensuring
clips fully engage.
84mm
1 2 3 4
45mm
30mm
NOTE: Ensure wall behind Front
Plate in this area is completely clear
Any other configuration
will default to 2 hrs
1 2 3 4
2 hrs 1 2 3 4
4 hrs
1 2 3 4
6 hrs 1 2 3 4
8 hrs
Front Plate
Mounting Screw
Cover Plate
To A/C
To remove Cover Plate once assembled onto the wall, use a small flat head
screwdriver in the locations shown to pry Cover Plate off of the Front Plate.
1
2
PLATINUM II
67
MOTION SENSOR/TIMER SET UP
7. Wiring Diagram
Pin connections from Timer and/or SIPS Control Box for A/C control as shown
(colours are as supplied cable).
WIRING DIAGRAM
PIN 1
PIN 6
PIN 2 (GREEN)
PIN 3
(ORANGE/WHITE)
PIN 5
(BLUE/WHITE)
PIN 6 (BLUE)
PIN 1 GREEN/WHITE NOT USED
PIN 2 GREEN 0V
PIN 3 ORANGE/WHITE +12V
PIN 4 ORANGE MODE
PIN 5 BLUE/WHITE RELAY C
PIN 6 BLUE RELAY NO
MODE changes LED colour from blue to orange
8. Multiple Timers using SIPS
Up to 8 Timers can be used in a multi-Zone system using a SIPS01 Control Box.
Refer configuration diagram on page 9 for a typical system design.
Each Timer must be plugged into same port on the SIPS01 as corresponding
Zone Damper on the RMC04. Ensure all connections are made before powering
on the system.
MULTIPLE TIMERS USING SIPS
240VAC
Power Cord
SIPS Control Box
Timer Cables
Touch Screen Cable
(optional)
Mounting Screw
LED light
indicates
power
To A/C
Link Cable
to RMC04
PLATINUM II
67
MOTION SENSOR/TIMER SET UP
7. Wiring Diagram
Pin connections from Timer and/or SIPS Control Box for A/C control as shown
(colours are as supplied cable).
WIRING DIAGRAM
PIN 1
PIN 6
PIN 2 (GREEN)
PIN 3
(ORANGE/WHITE)
PIN 5
(BLUE/WHITE)
PIN 6 (BLUE)
PIN 1 GREEN/WHITE NOT USED
PIN 2 GREEN 0V
PIN 3 ORANGE/WHITE +12V
PIN 4 ORANGE MODE
PIN 5 BLUE/WHITE RELAY C
PIN 6 BLUE RELAY NO
MODE changes LED colour from blue to orange
8. Multiple Timers using SIPS
Up to 8 Timers can be used in a multi-Zone system using a SIPS01 Control Box.
Refer configuration diagram on page 9 for a typical system design.
Each Timer must be plugged into same port on the SIPS01 as corresponding
Zone Damper on the RMC04. Ensure all connections are made before powering
on the system.
MULTIPLE TIMERS USING SIPS
240VAC
Power Cord
SIPS Control Box
Timer Cables
Touch Screen Cable
(optional)
Mounting Screw
LED light
indicates
power
To A/C
Link Cable
to RMC04
PLATINUM II
89
MOTION SENSOR/TIMER SET UP
9. Multiple Timer Configuration
When configured correctly, pressing a Timer button switches on the A/C and
opens the corresponding Zone Damper to 100% (or desired Max %, which can be
adjusted using the Zone Balance feature) for the set time period. All other Zone
Dampers remain closed. Pushing any other Timer button will open the
corresponding Zone Damper and extend the A/C operation by the set time
period. A second press on an active Timer will halt the countdown for that Zone
and close the corresponding Zone Damper. Once all the Timers expire, the A/C is
switched off and all Zone Dampers are closed.
NOTE: The assumption is the A/C wall control and the Platinum II Touch Screen
will only be accessible to the installer and not the end user of the Timer.
ŸIf A/C system is turned on or off at the wall control, there is no effect on the
Timer countdown, if active.
ŸIf the Platinum II system is turned off at the Touch Screen, all Zone Dampers
will open – if the A/C is on, every Zone will get air regardless of the Timer
status.
NOTE: If Timers are used without the link to the A/C, the duct system may need
to be designed with appropriate Relief Zones, so that if all the Zones are closed,
the A/C will not be damaged.
For the Platinum II system to know if it is in Heating or Cooling Mode requires an
Auto system configuration with the use of a Duct Sensor and temperature
Sensors in each room.
To A/C
Timer - Zone 1 Timer - Zone 2 Timer - Zone 3
SIPSRMC04RMC04
Link Cable
TS01 TS01 (optional)
Zone 1
Zone 2
Zone 3
MULTIPLE TIMER CONFIGURATION MULTIPLE TIMER FUNCTION
(optional)
PLATINUM II
89
MOTION SENSOR/TIMER SET UP
9. Multiple Timer Configuration
When configured correctly, pressing a Timer button switches on the A/C and
opens the corresponding Zone Damper to 100% (or desired Max %, which can be
adjusted using the Zone Balance feature) for the set time period. All other Zone
Dampers remain closed. Pushing any other Timer button will open the
corresponding Zone Damper and extend the A/C operation by the set time
period. A second press on an active Timer will halt the countdown for that Zone
and close the corresponding Zone Damper. Once all the Timers expire, the A/C is
switched off and all Zone Dampers are closed.
NOTE: The assumption is the A/C wall control and the Platinum II Touch Screen
will only be accessible to the installer and not the end user of the Timer.
ŸIf A/C system is turned on or off at the wall control, there is no effect on the
Timer countdown, if active.
ŸIf the Platinum II system is turned off at the Touch Screen, all Zone Dampers
will open – if the A/C is on, every Zone will get air regardless of the Timer
status.
NOTE: If Timers are used without the link to the A/C, the duct system may need
to be designed with appropriate Relief Zones, so that if all the Zones are closed,
the A/C will not be damaged.
For the Platinum II system to know if it is in Heating or Cooling Mode requires an
Auto system configuration with the use of a Duct Sensor and temperature
Sensors in each room.
To A/C
Timer - Zone 1 Timer - Zone 2 Timer - Zone 3
SIPSRMC04RMC04
Link Cable
TS01 TS01 (optional)
Zone 1
Zone 2
Zone 3
MULTIPLE TIMER CONFIGURATION MULTIPLE TIMER FUNCTION
(optional)
PLATINUM II
10 11
MOTION SENSOR/TIMER SET UP
MOUNTING THE MOTION SENSOR
10. Mounting the Motion Sensor
ŸChoose an appropriate position on the ceiling to mount the Motion Sensor.
ŸMark and cut out hole in ceiling as shown, then use the Mounting Plate to
mark holes for the screw fixings.
ŸUse the appropriate supplied fixings for the ceiling material.
ŸFeed the cables from the ceiling through the Mounting Plate, then screw
Mounting Plate to the ceiling.
ŸPlug in cables as required, then clip on Cover assembly to complete installation.
MULTIPLE MOTION SENSORS USING SIPS
11. Multiple Motion Sensors using SIPS
Up to 8 Motion Sensors can be used in a multi-Zone system using a SIPS01
Control Box. Refer configuration diagram on page 13 for a typical system design.
Each Motion Sensor must be plugged into same port on the SIPS01 as
corresponding Zone Damper on the RMC04. Ensure all connections are made
before powering on the system.
Mounting
Plate
Cover
Mounting
Screw
To Timer
(Optional)
To Timer
(Optional)
To SIPS ModuleTo SIPS Module
23
50 240VAC
Power Cord
SIPS Control Box
Motion Sensor
Cables
Touch Screen Cable
(optional)
Mounting Screw
LED light
indicates
power
To A/C
Link Cable
to RMC04
2.4m
Ø6.0m
PLATINUM II
10 11
MOTION SENSOR/TIMER SET UP
MOUNTING THE MOTION SENSOR
10. Mounting the Motion Sensor
ŸChoose an appropriate position on the ceiling to mount the Motion Sensor.
ŸMark and cut out hole in ceiling as shown, then use the Mounting Plate to
mark holes for the screw fixings.
ŸUse the appropriate supplied fixings for the ceiling material.
ŸFeed the cables from the ceiling through the Mounting Plate, then screw
Mounting Plate to the ceiling.
ŸPlug in cables as required, then clip on Cover assembly to complete installation.
MULTIPLE MOTION SENSORS USING SIPS
11. Multiple Motion Sensors using SIPS
Up to 8 Motion Sensors can be used in a multi-Zone system using a SIPS01
Control Box. Refer configuration diagram on page 13 for a typical system design.
Each Motion Sensor must be plugged into same port on the SIPS01 as
corresponding Zone Damper on the RMC04. Ensure all connections are made
before powering on the system.
Mounting
Plate
Cover
Mounting
Screw
To Timer
(Optional)
To Timer
(Optional)
To SIPS ModuleTo SIPS Module
23
50 240VAC
Power Cord
SIPS Control Box
Motion Sensor
Cables
Touch Screen Cable
(optional)
Mounting Screw
LED light
indicates
power
To A/C
Link Cable
to RMC04
2.4m
Ø6.0m
PLATINUM II
12 13
MOTION SENSOR/TIMER SET UP
12. Motion Sensor Configuration
When configured correctly, using Motion Sensors eliminates the requirement for
unused Zones to be air-conditioned.
For a Manual System, in any Zone every 20 minutes without motion detection,
the Zone Damper closes from 100% to 70%, then 30%, then fully closed. If
motion is detected, the Zone Damper resets to its original position.
For an Auto System, in any Zone every 20 minutes without motion detection, the
Zone Damper maximum opening limit changes from 100% to 70%, then 30%
then fully closed. If motion is detected, the Zone Damper resets to its original
position.
NOTE: The duct system may need to be designed with appropriate Relief Zones,
so that if all the Zones are closed, the A/C will not be damaged, however, the
system can also be configured so that the A/C is switched off if all Motion
Sensors result in all Zones fully closing.
MOTION SENSOR CONFIGURATION MOTION SENSOR CONFIGURATION
To A/C
SIPSRMC04RMC04
Link Cable
TS01 TS01 (optional)
Zone 1
Zone 2
Zone 3
Motion Sensor
Zone 1 Motion Sensor
Zone 2 Motion Sensor
Zone 3
(optional)
PLATINUM II
12 13
MOTION SENSOR/TIMER SET UP
12. Motion Sensor Configuration
When configured correctly, using Motion Sensors eliminates the requirement for
unused Zones to be air-conditioned.
For a Manual System, in any Zone every 20 minutes without motion detection,
the Zone Damper closes from 100% to 70%, then 30%, then fully closed. If
motion is detected, the Zone Damper resets to its original position.
For an Auto System, in any Zone every 20 minutes without motion detection, the
Zone Damper maximum opening limit changes from 100% to 70%, then 30%
then fully closed. If motion is detected, the Zone Damper resets to its original
position.
NOTE: The duct system may need to be designed with appropriate Relief Zones,
so that if all the Zones are closed, the A/C will not be damaged, however, the
system can also be configured so that the A/C is switched off if all Motion
Sensors result in all Zones fully closing.
MOTION SENSOR CONFIGURATION MOTION SENSOR CONFIGURATION
To A/C
SIPSRMC04RMC04
Link Cable
TS01 TS01 (optional)
Zone 1
Zone 2
Zone 3
Motion Sensor
Zone 1 Motion Sensor
Zone 2 Motion Sensor
Zone 3
(optional)
PLATINUM II
14 15
MOTION SENSOR/TIMER SET UP
NOTE: Although the
maximum number of
Motion Sensors that can be
used is 8, Motion Sensors
can be used on systems with
more than 8 Zones by
configuring the system as
shown. Motion Sensors can
only be used on Zones 1-8.
MOTION SENSOR CONFIGURATION ADD-ON TIMER CONFIGURATION
To A/C
SIPSRMC04RMC04 RMC04RMC04
Link CableLink Cable
Zone 1
Zone 2
Zone 3
Motion Sensor
Zone 1 Motion Sensor
Zone 2 Motion Sensor
Zone 3
TS01 TS01 (optional)
13. Motion Sensor with Add-On Timer Configuration
Motion Sensors can be used with Timers for an even more efficient system.
Motion Sensor functionality will operate for as long as the Timer is active. If the
Timer is switched off or reaches the end of the countdown period, the Motion
Sensors will not be active. Refer configuration diagram below for a typical
system design.
To A/C
Timer - Zone 1 Timer - Zone 2 Timer - Zone 3
SIPSRMC04RMC04
Link Cable
Zone 1
Zone 2
Zone 3
TS01 TS01 (optional)
Motion Sensor
Zone 1
Motion Sensor
Zone 1 Motion Sensor
Zone 2
Motion Sensor
Zone 2 Motion Sensor
Zone 3
Motion Sensor
Zone 3
(optional)
(optional)
PLATINUM II
14 15
MOTION SENSOR/TIMER SET UP
NOTE: Although the
maximum number of
Motion Sensors that can be
used is 8, Motion Sensors
can be used on systems with
more than 8 Zones by
configuring the system as
shown. Motion Sensors can
only be used on Zones 1-8.
MOTION SENSOR CONFIGURATION ADD-ON TIMER CONFIGURATION
To A/C
SIPSRMC04RMC04 RMC04RMC04
Link CableLink Cable
Zone 1
Zone 2
Zone 3
Motion Sensor
Zone 1 Motion Sensor
Zone 2 Motion Sensor
Zone 3
TS01 TS01 (optional)
13. Motion Sensor with Add-On Timer Configuration
Motion Sensors can be used with Timers for an even more efficient system.
Motion Sensor functionality will operate for as long as the Timer is active. If the
Timer is switched off or reaches the end of the countdown period, the Motion
Sensors will not be active. Refer configuration diagram below for a typical
system design.
To A/C
Timer - Zone 1 Timer - Zone 2 Timer - Zone 3
SIPSRMC04RMC04
Link Cable
Zone 1
Zone 2
Zone 3
TS01 TS01 (optional)
Motion Sensor
Zone 1
Motion Sensor
Zone 1 Motion Sensor
Zone 2
Motion Sensor
Zone 2 Motion Sensor
Zone 3
Motion Sensor
Zone 3
(optional)
(optional)
MOTION SENSOR CONFIGURATION - NO ZONES ADD-ON TIMER CONFIGURATION - NO ZONES
PLATINUM II
16 17
MOTION SENSOR/TIMER SET UP
15. Motion Sensor with Add-On Timer Configuration - No Zones
Motion Sensors can be used with Timers for an even more efficient system. Up
to 8 Motion Sensors with add-on Timers may be used.
Functionality is as previously described but if the Timer is switched off or
reaches the end of the set countdown period, the Motion Sensors will not be
active.
Refer configuration diagram below for a typical system design.
14. Motion Sensor Configuration - No Zones
One or more Motion Sensors can be used to directly switch on/off an A/C unit
that does not utilize a Zone system. Up to 8 Motion Sensors may be used.
NOTE: To use the Motion Sensors with an A/C, the A/C must have external
control input. Refer to A/C unit wiring diagram. Once installed, the indoor unit
must be set to enable external control operation - the method will vary from
model to model.
If a Motion Sensor detects no motion after 1 hour, the A/C will be switched off.
If more than one Motion Sensor is used, it requires all Sensors to have not
detected motion in 1 hour to switch off the A/C. If motion is detected, it will
switch on the A/C and reset the countdown.
Refer configuration diagram below for a typical system design.
To A/C
SIPS
Motion Sensor 1Motion Sensor 1 Motion Sensor 2Motion Sensor 2 Motion Sensor 3Motion Sensor 3
To A/C
Timer 1 Timer 2 Timer 3
SIPS
Motion Sensor 1Motion Sensor 1 Motion Sensor 2Motion Sensor 2 Motion Sensor 3Motion Sensor 3
MOTION SENSOR CONFIGURATION - NO ZONES ADD-ON TIMER CONFIGURATION - NO ZONES
PLATINUM II
16 17
MOTION SENSOR/TIMER SET UP
15. Motion Sensor with Add-On Timer Configuration - No Zones
Motion Sensors can be used with Timers for an even more efficient system. Up
to 8 Motion Sensors with add-on Timers may be used.
Functionality is as previously described but if the Timer is switched off or
reaches the end of the set countdown period, the Motion Sensors will not be
active.
Refer configuration diagram below for a typical system design.
14. Motion Sensor Configuration - No Zones
One or more Motion Sensors can be used to directly switch on/off an A/C unit
that does not utilize a Zone system. Up to 8 Motion Sensors may be used.
NOTE: To use the Motion Sensors with an A/C, the A/C must have external
control input. Refer to A/C unit wiring diagram. Once installed, the indoor unit
must be set to enable external control operation - the method will vary from
model to model.
If a Motion Sensor detects no motion after 1 hour, the A/C will be switched off.
If more than one Motion Sensor is used, it requires all Sensors to have not
detected motion in 1 hour to switch off the A/C. If motion is detected, it will
switch on the A/C and reset the countdown.
Refer configuration diagram below for a typical system design.
To A/C
SIPS
Motion Sensor 1Motion Sensor 1 Motion Sensor 2Motion Sensor 2 Motion Sensor 3Motion Sensor 3
To A/C
Timer 1 Timer 2 Timer 3
SIPS
Motion Sensor 1Motion Sensor 1 Motion Sensor 2Motion Sensor 2 Motion Sensor 3Motion Sensor 3
Zones with Motion Sensors
and/or Timers are highlighted
in green. If there is a fault
with a Motion Sensor or
Timer, it will be highlighted in
red.
PLATINUM II
SYSTEM SET UP
MOTION SENSOR/TIMER SET UP
18
16. System Set Up
Motion Sensors and/or Timers
will be automatically detected
only after the initial set up
process has been completed.
After the initial set up process,
information related to Motion
Sensors and/or Timers is
accessed from the System Set
Up screen by pressing the
settings icon on the top right
corner of Base Screen
(installer code will be
required).
NOTE: Motion Sensors and/or
Timers not automatically
detected after the initial set
up process will not register as
a Fault - only devices
recognized during the initial
set up process will register as
a fault should they fail or
become disconnected at a
later stage.
19
SYSTEM SET UP
PLATINUM II
Other manuals for PLATINUM II
2
Table of contents
