A-Neuvideo ANI-FIBER-F02P User manual

AUDIO / VIDEO MANUFACTURER
ANI-FIBER-F02P
4K Fiber Optic HDMI Extender - 3300 FT/1000M - 4K@60Hz w/
IR, RS-232, HDMI 2.0 Support
A-NeuVideo.com
Frisco, Texas 75036
INSTRUCTION MANUAL

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your
equipment. Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain,
water and excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean
dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they
are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and
plugs, convenience receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken
so that the means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper
AC voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold.
Do not use the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may
impede the normal ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used
in an extremely dusty or smoky environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all
servicing to qualied service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the interconnecting
cables to other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship
the unit, use only the original factory packing.
19. Service Information Equipment should be serviced by qualied service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain.
D. The equipment does not appear to operate normally, or exhibits a marked change in performance.
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY
INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.

ANEUVIDEO
1
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power
supply. Please keep the following in mind as you unpack and install this equipment:
• Always follow basic safety precautions to reduce the risk of re, electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow
for sufcient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and is believed to be accurate. We assume no responsibility for
any infringements of patents or other rights of third parties which may result from its use.
We assume no responsibility for any inaccuracies that may be contained in this document. We make no commitment to update
or to keep current the information contained in this document.
We reserve the right to make improvements to this document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means — electronic, mechanical, magnetic, optical, chemical,
manual, or otherwise — without the express written permission and consent.
© Copyright 2021. All Rights Reserved.
Version 1.0 JUNE 2021
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be trademarks of the companies with which they are associated.

ANEUVIDEO
2
TABLE OF CONTENTS
INTRODUCTION & CONTENTS......................................................................................................2
FEATURES.......................................................................................................................................3
SPECIFICATIONS............................................................................................................................4
OPERATION CONTROLS & FUNCTIONS.......................................................................................5
CONNECTION DIAGRAM.................................................................................................................8
INTRODUCTION
This HDMI Extender can extend HDMI signal up to 3300 ft/1000M (over single-mode ber cable) or
1000 ft/300M (over multi-mode ber cable). Video resolution is up to 4K2K@60Hz 4:4:4. Transmitter
supports loop output, audio embeding and EDID managment function. Receiver supports audio
extracting function. In addition, the extender supports bidirectional IR control and RS-232 signal
pass-through. It can allow you to easily control the display device on the signal source side or control
the signal source device on the display side when using this extender. This product has a 3 year
warranty.
PACKAGE CONTENTS
Before attempting to use this unit, please check the packaging and make sure the following items
are contained in the shipping carton:
• ANI-FIBER-F02P18Gbps HDMI over Optical Fiber Extender (Transmitter)
• ANI-FIBER-F02P 18Gbps HDMI over Optical Fiber Extender (Receiver)
• SFP-BL35T1-02DC Transmitter
• SFP-BL531T-02DC Receiver
• IR Blaster cable (4.9 FT/1.5M)
• IR Receiver cable (4.9 FT/1.5M)
• (2) 5V/1A Power adapter
• (2) 3-pin Phoenix connector (RS-232)
• Users Guide

3
FEATURES
• HDMI 2.0b, HDCP 2.2 and DVI 1.0 compliant
• Supports 18Gbps video bandwidth
• Video resolution up to 4K2K@50/60Hz 4:4:4
• HDMI audio formats: LPCM2/5.1/7.1CH, Dolby Digital/Plus/EX, Dolby True HD, DTS, DTS-EX,
DTS-96/24, DTS High Res, DTS-HD Master Audio, DSD
• Supports 3D and HDR format video, does not support CEC control
• Transmission distance up to 3300 ft/1000M (over single-mode ber cable) or 1000 ft/300M (over
multi-mode ber cable) (50/125um/OM3)
• Supports bidirectional IR control, RS-232 pass-through and EDID management for simple and
convenient control
• Transmitter supports loop output (sharing local HD video and audio) and audio embeding function
• Receiver supports audio extracting output function
• Compact design for easy and exible installation

4
SPECIFICATIONS
• HDMI Compliance: HDMI 2.0b
• HDCP Compliance: HDCP 2.2
• Video Bandwidth: 18Gbps
• Video Resolution: 480i ~1080p50/60Hz, 4K2K@24/30Hz, 4K2K@60Hz
• Color Space: RGB, YCbCr 4:4:4 / 4:2:2, YUV 4:2:0
• Color Depth: 8/10/12-bit (1080P60Hz) / 8-bit (4K60Hz)
• HDMI Audio Formats: LPCM2/5.1/7.1CH, Dolby Digital/Plus/EX, Dolby True HD, DTS, DTS-
EX, DTS-96/24, DTS High Res, DTS-HD Master Audio, DSD
• Transmission Distance: Up to 3300 ft/1000M over single-mode ber cable / Up to 1000 ft/
300M over multi-mode ber cable
• IR Frequency: 20KHz-60KHz
• RS-232 Baud Rate: 4800-115200bps
• ESD Protection Human body model:
• ±8kV (air-gap discharge) / ±6kV (contact discharge)
• Transmitter:
• Input:
• HDMI IN [Type A 19-pin female]
• LINE IN [3.5mm Stereo Mini-jack]
• IR IN [3.5mm Stereo Mini-jack]
• RS-232 [3.81mm Phoenix connector]
• SERVICE [Micro USB, Update port]
• Output:
• HDMI OUT [Type A 19-pin female]
• Optical Fiber Out [LC female]
• IR OUT [3.5mm Stereo Mini-jack]
• Receiver:
• Input:
• Optical Fiber In [LC female]
• IR IN [3.5mm Stereo Mini-jack]
• SERVICE [Micro USB, Update port]
• Output:
• HDMI OUT [Type A 19-pin female]
• RS-232 [3.81mm Phoenix connector]
• IR OUT [3.5mm Stereo Mini-jack]
• AUDIO OUT [3.5mm Stereo Mini-jack]
• Housing: Metal Enclosure
• Color: Black
• Dimensions (WxDxH): 5.28 x 2.7 x .7 in (134x68x18mm)
• Weight: Transmitter: 9.9 oz / 280g / Receiver: 9.8 / 278g
• Power Supply: Input: AC 100 - 240V 50/60Hz / Output: DC 5V/1A (US/EU standards, CE/FCC/UL certied)
• Operating Temperature: 0ºC~40ºC/32ºF~104ºF
• Storage Temperature: −20ºC~60ºC/−4ºF~140ºF
• Relative Humidity: 20~90% RH (non-condensing)
• Power Consumption: Transmitter: 3.85 W (Max), Receiver: 2.7 W (Max)
As product improvements are continuous, specications are subject to change without notice.

5
OPERATION CONTROLS AND FUNCTIONS
Transmitter Panel
qPOWER LED: The power indicator is always on when the Receiver is powered on.
wFIBER LED: The optical ber connection indicator is always on when the Transmitter and Receiver
establish a normal optical ber signal connection.
e HDMI LED:
IN: The HDMI signal input indicator is always on when there is signal input on the HDMI IN port.
LOOP: The HDMI loop output indicator is always on when the HDMI OUT port of the Transmitter
outputs signals to the HDMI display device.
r IR IN: Connect to IR Receiver cable. The IR signal will send to the IR OUT port of the Receiver.
t IR OUT: Connect to IR Blaster cable. The IR signal is from the IR IN port of the Receiver.
y AUDIO SWITCH: Switch to select audio signal source (HDMI IN or LINE IN). When there is no
video signals input, audio signals can be transmitted separately.
u EDID DIP SWITCH: Dial the switch to set EDID.
11: Copy RX HDMI OUT
10: Copy TX HDMI LOOP OUT
01: 4K60_2CH
00: 1080P_2CH
i SERVICE PORT: Firmware update port.
o DC 5V: DC 5V/1A power supply port
a FIBER: Connect the Transmitter optical ber module, and transmit signals to the Receiver via an
optical ber cable.
s HDMI OUT: HDMI video loop output port, connect to HDMI display device such as TV or Projector
with an HDMI cable.

6
OPERATION CONTROLS AND FUNCTIONS
d HDMI IN: HDMI signal input port, connect to HDMI source device such as DVD or PC with an
HDMI cable.
f LINE IN: Audio signal input port, connect to audio source device such as MP3.
g RS-232: RS-232 signal pass-through port for transmitting RS-232 command signals between the
Transmitter and Receiver.

7
OPERATION CONTROLS AND FUNCTIONS
Receiver Panel
qPOWER LED: The power indicator is always on when the Receiver is powered on.
wFIBER LED: The optical ber connection indicator is always on when the Transmitter and Receiver
establish a normal optical ber signal connection.
eHDMI LED: The HDMI signal output indicator is always on when the HDMI OUT port of the
Receiver outputs signals to the HDMI display device.
rIR IN: Connect to IR Receiver cable. The IR signal will send to the IR OUT port of the Transmitter.
tIR OUT: Connect to IR Blaster cable. The IR signal is from the IR IN port of the Transmitter.
ySERVICE PORT: Firmware update port.
uDC 5V: DC 5V/1A power supply port
iFIBER: Connect the Receiver optical ber module, and receive signals from the Transmitter via
an optical ber cable.
oHDMI OUT: HDMI signal output port, connect to HDMI display device such as HDTV or Projector
with an HDMI cable.
aAUDIO OUT: Audio signal extracting output port (extract the HDMI OUT audio signal), connect to
audio output device such as amplier or speaker.
sRS-232: RS-232 signal pass-through port for transmitting RS-232 command signals between the
Transmitter and Receiver.

8
IR Pin Definition
IR Receiver and Blaster pin’s definition as below:
Optical Fiber Module (INCLUDED)
qSFP-BL35T1-02DC: is the optical ber module for the Transmitter.
wSFP-BL531T-02DC: is the optical ber module of the Receiver.
Connect using a single ber cable.
Interface: LC Simplex to LC Simplex

9
CONNECTION DIAGRAM
The terms HDMI and HDMI High-Denition Multimedia interface, and the HDMI Logo are trademarks
or registered trademarks of HDMI Licensing LLC in the United States and other countries.

TERMS AND CONDITIONS OF USE
PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY,
THROUGH OR UNDER A-NeuVideo, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to
these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to A-NeuVideo, Inc. at the return address
set forth on the Product’s packing label at your expense. A-NeuVideo, Inc. may modify these Terms and Conditions at anytime, without notice to you.
RESTRICTIONS ON USE OF THE PRODUCT
It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product. You
are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any warranty
pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be borne by you
and you agree to indemnify and hold harmless A-NeuVideo, Inc. from and against any such damage.
The Product is protected by certain intellectual property rights owned by or licensed to A-NeuVideo. Any intellectual property rights pertaining to the Product are
licensed to you by A-NeuVideo, Inc. and/or its afliates, including any manufacturers or distributors of the Product (collectively, “A-NeuVideo”) for your personal use
only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.
The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by A-NeuVideo for your personal use only. A-NeuVideo
does not transfer either the title or the intellectual property rights to the Product and A-NeuVideo retains full and complete title to the intellectual property rights therein.
All trademarks and logos are owned by A-NeuVideo or its licensors and providers of the Product, and you may not copy or use them in any manner without the prior
written consent of A-NeuVideo, which consent may be withheld at the sole discretion of A-NeuVideo.
The functionality and usability of the Product is controlled by A-NeuVideo, Inc. from its ofces within the State of Texas, United States of America. A-NeuVideo makes no
representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided with respect
thereto. You are advised that the Product may be subject to U.S. export controls.
DISCLAIMERS AND LIMITATION OF LIABILITY
A-NeuVideo may change or modify the Product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. A-NEUVIDEO DOES NOT WARRANT OR
MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY,
OR OTHERWISE.
A-NeuVideo has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should not be
relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical inaccuracies or
typographical errors. Changes may be made from time to time without notice with respect to the Product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, A-NEUVIDEO DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. A-NEUVIDEO
DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT. A-NEUVIDEO DOES
NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO THE PRODUCT WILL BE
CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS. A-NEUVIDEO WILL USE ITS
REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU NOT TO EXCEED 10 BUSINESS DAYS
AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT A-NEUVIDEO) ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR AND
CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY A-NEUVIDEO.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL A-NEUVIDEO BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL
DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS, EVEN IF
A-NEUVIDEO OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL A-NEUVIDEO’S TOTAL
LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT YOU PAID
TO A-NEUVIDEO, IF ANY, FOR THE PRODUCT.
END OF DOCUMENT