A-oneTech AIR HALO User manual

2
3
4
5
4. Vacuum clean any dust
or obstruction within
5. Return the dry dust filter
and align vent cover
6. Push vent cover down
until it locks securely
1
1. Insert a small and thin tool into the pinhole
2. Push firmly until it clicks and/or the vent
cover pops out
3. Remove the dust filter, wash clean and dry
8.4 Out-vent
Vacuum the in-vent carefully, use a cotton
bud to remove dirt and dust from between the
vents.
8.3 In-vent
Use a slightly damp cloth to wipe clean any
blemish or dirt on the surface.
8.2 Surfaces
Before cleaning please Turn Off.
1. Surfaces: Slightly damp cloth
2. In-vent: Cotton bud & vacuum
3. Out-vent: Wash dust filter & vacuum
8.1 Cleaning recommendation
1
2
3
CAUTION: Replacing the Li-ion battery
incorrectly will severely damage your Air Halo.
To replace the rechargeable Li-ion battery:
8.5 Battery Replacement
Damaged Li-ion battery should be recycled or
disposed separately from household waste.
Maintenance repair by user is not advised.
For more details please see: 11.1 Warranty
• Model: AH01
• Power Mode: Silent / Normal / Boost
• Weight: 325g
• Air Sanitizer Technology: Plascide reactors
• Recommend Usage: 1m3
•
• Li-ion Battery: 18650 (cylinder-type)
• Dimension: 183mm (H), 63mm–83mm (W),
34mm–63mm (D)
8.7 Repair
8.6 Battery Disposal
1. Unscrew the
fastener
2. Remove the
battery cover
3. Replace battery
with Positive
end facing
downwards
4. Re-fasten the
battery cover
6.4 Charging
2.1A
8.5 Battery
Replacement
11.1 Warranty
10.1 Diagnostic
• Air Halo is covered by a manufacturer
guarantee and warranty
• Self-repair and/or signs of tampering will
void the warranty
• Repairs should only be carried out by a
certified person
• Please refer to the included warranty card
for more details
11.1 Warranty
If your warranty card or any accessories are
missing, please contact your nearest service
centre or alternatively contact the main office:
TEL:
FAX:
EMAIL: [email protected]
WEB: www.a-onetech.com.hk
11.3 Contact
11.2 Support
For all the latest Air Halo’s documentation,
please visit the support webpage:
www.a-onetech.com.hk/en-downloads
This device complies with Part 15 of the FCC Rules
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operations.
CAN ICE-3 (B)/NMB-3(B)
INSTRUCTION MANUAL
PORTABLE AIR SANITIZER
PLEASE READ THIS MANUAL BEFORE USE
M
EN
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.

2
1
5
6
3
4
6
5
4
3
2
1
1 OVERVIEW
Long press: turn On & Off / Short press to cycle modes
Clean air exits here
Rechargeable battery
Communication connectors
Contaminated air enters here
Micro-USB socket
Preparation before use:
1. On the Battery Cover remove the battery
Plascide’s Micro-lightning
Anti-germ & VOCs technology
ACTIVE SANITIZATION
No germ-filled filters
No replacement cost
FILTER-LESS PROCESS
Sanitize within seconds
RAPID EFFECTIVENESS
Hours of battery operation
Wherever you go
CORDLESS PROTECTION
protector with the
pull-out tab
2. Charge the Air Halo
until battery is full
Please see:
6.4 Charging
1. Air Halo Sanitizer
2. Li-ion battery (Installed)
3. Micro-USB to USB cable
4. Manual
5. Warranty Card
1. Handle with care. Air Halo
can be damaged if dropped,
burned, punctured or
crushed.
2. Do not operate if damaged
and/or when the case is
broken to avoid potential
injury.
3. Charge with a Micro-USB
cable and a compatible USB
power adapter at 2.1A or
higher.
4. Do not charge or operate
with damaged Micro-USB
cables or damaged USB
power adapters.
5. Keep dry during operation
and storage. Do not operate
if wet and/or immersed in
any liquid to avoid potential
injuries and/or damages to
properties.
6. Do not allow infants and/
or young children to operate
unsupervised.
7. Do not insert any objects into
the in or out air-vents.
8. Do not operate without the
Out air-vent cover.
9. Do not block the In or Out
air-vents during operation.
10. Do not incinerate the Li-ion
battery. Recycle or dispose
separately from household
waste.
6.2 Operational Modes
6.3 Mode Selection
6.4 Charging
*
*low-light mode
1.
2.
LED will flash when cycled
6.1 Function Button
1. Charge with a Micro-USB cable
2. Connect the Micro-USB plug to the Air Halo
3. Connect the USB plug to a power adapter
Immediately after turning on, default mode is set
to .
SHORT
PRESS
NORMAL
BOOST
LONG
PRESS
TURN ON
SILENT
Pairing allows two Air Halos to function as
one when placed together or occupy the same
cupholder. Control both from any button and
charge from one USB cable.
Before Pairing, Switch ON both Air Halos
For more details see: 6.1 Function Button
Only one USB cable connected is required to
charge both units when using a generic power
adapter at 2.1A or higher.
For more details see: 6.4 Charging
1. Place the rear flat
face of the Air Halos
together
2. Align the Pairing Link
at the bottom
3. Both units will snap
together magnetically
4. Air Halos will begin
pairing automatically
5. Wait a few seconds
for pairing to finish
7.1 Air Halo Pairing
7.2 Mode Selection when Paired
7.3 Charge When Paired
and do not separate the connection
6. Once synchronised, paired control will now
be enabled until you separate or switch off

2
1
5
6
3
4
6
5
4
3
2
1
1 OVERVIEW
Long press: turn On & Off / Short press to cycle modes
Clean air exits here
Rechargeable battery
Communication connectors
Contaminated air enters here
Micro-USB socket
Preparation before use:
1. On the Battery Cover remove the battery
Plascide’s Micro-lightning
Anti-germ & VOCs technology
ACTIVE SANITIZATION
No germ-filled filters
No replacement cost
FILTER-LESS PROCESS
Sanitize within seconds
RAPID EFFECTIVENESS
Hours of battery operation
Wherever you go
CORDLESS PROTECTION
protector with the
pull-out tab
2. Charge the Air Halo
until battery is full
Please see:
6.4 Charging
1. Air Halo Sanitizer
2. Li-ion battery (Installed)
3. Micro-USB to USB cable
4. Manual
5. Warranty Card
1. Handle with care. Air Halo
can be damaged if dropped,
burned, punctured or
crushed.
2. Do not operate if damaged
and/or when the case is
broken to avoid potential
injury.
3. Charge with a Micro-USB
cable and a compatible USB
power adapter at 2.1A or
higher.
4. Do not charge or operate
with damaged Micro-USB
cables or damaged USB
power adapters.
5. Keep dry during operation
and storage. Do not operate
if wet and/or immersed in
any liquid to avoid potential
injuries and/or damages to
properties.
6. Do not allow infants and/
or young children to operate
unsupervised.
7. Do not insert any objects into
the in or out air-vents.
8. Do not operate without the
Out air-vent cover.
9. Do not block the In or Out
air-vents during operation.
10. Do not incinerate the Li-ion
battery. Recycle or dispose
separately from household
waste.
6.2 Operational Modes
6.3 Mode Selection
6.4 Charging
*
*low-light mode
1.
2.
LED will flash when cycled
6.1 Function Button
1. Charge with a Micro-USB cable
2. Connect the Micro-USB plug to the Air Halo
3. Connect the USB plug to a power adapter
Immediately after turning on, default mode is set
to .
SHORT
PRESS
NORMAL
BOOST
LONG
PRESS
TURN ON
SILENT
Pairing allows two Air Halos to function as
one when placed together or occupy the same
cupholder. Control both from any button and
charge from one USB cable.
Before Pairing, Switch ON both Air Halos
For more details see: 6.1 Function Button
Only one USB cable connected is required to
charge both units when using a generic power
adapter at 2.1A or higher.
For more details see: 6.4 Charging
1. Place the rear flat
face of the Air Halos
together
2. Align the Pairing Link
at the bottom
3. Both units will snap
together magnetically
4. Air Halos will begin
pairing automatically
5. Wait a few seconds
for pairing to finish
7.1 Air Halo Pairing
7.2 Mode Selection when Paired
7.3 Charge When Paired
and do not separate the connection
6. Once synchronised, paired control will now
be enabled until you separate or switch off

2
1
5
6
3
4
6
5
4
3
2
1
1 OVERVIEW
Long press: turn On & Off / Short press to cycle modes
Clean air exits here
Rechargeable battery
Communication connectors
Contaminated air enters here
Micro-USB socket
Preparation before use:
1. On the Battery Cover remove the battery
Plascide’s Micro-lightning
Anti-germ & VOCs technology
ACTIVE SANITIZATION
No germ-filled filters
No replacement cost
FILTER-LESS PROCESS
Sanitize within seconds
RAPID EFFECTIVENESS
Hours of battery operation
Wherever you go
CORDLESS PROTECTION
protector with the
pull-out tab
2. Charge the Air Halo
until battery is full
Please see:
6.4 Charging
1. Air Halo Sanitizer
2. Li-ion battery (Installed)
3. Micro-USB to USB cable
4. Manual
5. Warranty Card
1. Handle with care. Air Halo
can be damaged if dropped,
burned, punctured or
crushed.
2. Do not operate if damaged
and/or when the case is
broken to avoid potential
injury.
3. Charge with a Micro-USB
cable and a compatible USB
power adapter at 2.1A or
higher.
4. Do not charge or operate
with damaged Micro-USB
cables or damaged USB
power adapters.
5. Keep dry during operation
and storage. Do not operate
if wet and/or immersed in
any liquid to avoid potential
injuries and/or damages to
properties.
6. Do not allow infants and/
or young children to operate
unsupervised.
7. Do not insert any objects into
the in or out air-vents.
8. Do not operate without the
Out air-vent cover.
9. Do not block the In or Out
air-vents during operation.
10. Do not incinerate the Li-ion
battery. Recycle or dispose
separately from household
waste.
6.2 Operational Modes
6.3 Mode Selection
6.4 Charging
*
*low-light mode
1.
2.
LED will flash when cycled
6.1 Function Button
1. Charge with a Micro-USB cable
2. Connect the Micro-USB plug to the Air Halo
3. Connect the USB plug to a power adapter
Immediately after turning on, default mode is set
to .
SHORT
PRESS
NORMAL
BOOST
LONG
PRESS
TURN ON
SILENT
Pairing allows two Air Halos to function as
one when placed together or occupy the same
cupholder. Control both from any button and
charge from one USB cable.
Before Pairing, Switch ON both Air Halos
For more details see: 6.1 Function Button
Only one USB cable connected is required to
charge both units when using a generic power
adapter at 2.1A or higher.
For more details see: 6.4 Charging
1. Place the rear flat
face of the Air Halos
together
2. Align the Pairing Link
at the bottom
3. Both units will snap
together magnetically
4. Air Halos will begin
pairing automatically
5. Wait a few seconds
for pairing to finish
7.1 Air Halo Pairing
7.2 Mode Selection when Paired
7.3 Charge When Paired
and do not separate the connection
6. Once synchronised, paired control will now
be enabled until you separate or switch off

2
1
5
6
3
4
6
5
4
3
2
1
1 OVERVIEW
Long press: turn On & Off / Short press to cycle modes
Clean air exits here
Rechargeable battery
Communication connectors
Contaminated air enters here
Micro-USB socket
Preparation before use:
1. On the Battery Cover remove the battery
Plascide’s Micro-lightning
Anti-germ & VOCs technology
ACTIVE SANITIZATION
No germ-filled filters
No replacement cost
FILTER-LESS PROCESS
Sanitize within seconds
RAPID EFFECTIVENESS
Hours of battery operation
Wherever you go
CORDLESS PROTECTION
protector with the
pull-out tab
2. Charge the Air Halo
until battery is full
Please see:
6.4 Charging
1. Air Halo Sanitizer
2. Li-ion battery (Installed)
3. Micro-USB to USB cable
4. Manual
5. Warranty Card
1. Handle with care. Air Halo
can be damaged if dropped,
burned, punctured or
crushed.
2. Do not operate if damaged
and/or when the case is
broken to avoid potential
injury.
3. Charge with a Micro-USB
cable and a compatible USB
power adapter at 2.1A or
higher.
4. Do not charge or operate
with damaged Micro-USB
cables or damaged USB
power adapters.
5. Keep dry during operation
and storage. Do not operate
if wet and/or immersed in
any liquid to avoid potential
injuries and/or damages to
properties.
6. Do not allow infants and/
or young children to operate
unsupervised.
7. Do not insert any objects into
the in or out air-vents.
8. Do not operate without the
Out air-vent cover.
9. Do not block the In or Out
air-vents during operation.
10. Do not incinerate the Li-ion
battery. Recycle or dispose
separately from household
waste.
6.2 Operational Modes
6.3 Mode Selection
6.4 Charging
*
*low-light mode
1.
2.
LED will flash when cycled
6.1 Function Button
1. Charge with a Micro-USB cable
2. Connect the Micro-USB plug to the Air Halo
3. Connect the USB plug to a power adapter
Immediately after turning on, default mode is set
to .
SHORT
PRESS
NORMAL
BOOST
LONG
PRESS
TURN ON
SILENT
Pairing allows two Air Halos to function as
one when placed together or occupy the same
cupholder. Control both from any button and
charge from one USB cable.
Before Pairing, Switch ON both Air Halos
For more details see: 6.1 Function Button
Only one USB cable connected is required to
charge both units when using a generic power
adapter at 2.1A or higher.
For more details see: 6.4 Charging
1. Place the rear flat
face of the Air Halos
together
2. Align the Pairing Link
at the bottom
3. Both units will snap
together magnetically
4. Air Halos will begin
pairing automatically
5. Wait a few seconds
for pairing to finish
7.1 Air Halo Pairing
7.2 Mode Selection when Paired
7.3 Charge When Paired
and do not separate the connection
6. Once synchronised, paired control will now
be enabled until you separate or switch off

2
1
5
6
3
4
6
5
4
3
2
1
1 OVERVIEW
Long press: turn On & Off / Short press to cycle modes
Clean air exits here
Rechargeable battery
Communication connectors
Contaminated air enters here
Micro-USB socket
Preparation before use:
1. On the Battery Cover remove the battery
Plascide’s Micro-lightning
Anti-germ & VOCs technology
ACTIVE SANITIZATION
No germ-filled filters
No replacement cost
FILTER-LESS PROCESS
Sanitize within seconds
RAPID EFFECTIVENESS
Hours of battery operation
Wherever you go
CORDLESS PROTECTION
protector with the
pull-out tab
2. Charge the Air Halo
until battery is full
Please see:
6.4 Charging
1. Air Halo Sanitizer
2. Li-ion battery (Installed)
3. Micro-USB to USB cable
4. Manual
5. Warranty Card
1. Handle with care. Air Halo
can be damaged if dropped,
burned, punctured or
crushed.
2. Do not operate if damaged
and/or when the case is
broken to avoid potential
injury.
3. Charge with a Micro-USB
cable and a compatible USB
power adapter at 2.1A or
higher.
4. Do not charge or operate
with damaged Micro-USB
cables or damaged USB
power adapters.
5. Keep dry during operation
and storage. Do not operate
if wet and/or immersed in
any liquid to avoid potential
injuries and/or damages to
properties.
6. Do not allow infants and/
or young children to operate
unsupervised.
7. Do not insert any objects into
the in or out air-vents.
8. Do not operate without the
Out air-vent cover.
9. Do not block the In or Out
air-vents during operation.
10. Do not incinerate the Li-ion
battery. Recycle or dispose
separately from household
waste.
6.2 Operational Modes
6.3 Mode Selection
6.4 Charging
*
*low-light mode
1.
2.
LED will flash when cycled
6.1 Function Button
1. Charge with a Micro-USB cable
2. Connect the Micro-USB plug to the Air Halo
3. Connect the USB plug to a power adapter
Immediately after turning on, default mode is set
to .
SHORT
PRESS
NORMAL
BOOST
LONG
PRESS
TURN ON
SILENT
Pairing allows two Air Halos to function as
one when placed together or occupy the same
cupholder. Control both from any button and
charge from one USB cable.
Before Pairing, Switch ON both Air Halos
For more details see: 6.1 Function Button
Only one USB cable connected is required to
charge both units when using a generic power
adapter at 2.1A or higher.
For more details see: 6.4 Charging
1. Place the rear flat
face of the Air Halos
together
2. Align the Pairing Link
at the bottom
3. Both units will snap
together magnetically
4. Air Halos will begin
pairing automatically
5. Wait a few seconds
for pairing to finish
7.1 Air Halo Pairing
7.2 Mode Selection when Paired
7.3 Charge When Paired
and do not separate the connection
6. Once synchronised, paired control will now
be enabled until you separate or switch off

2
3
4
5
4. Vacuum clean any dust
or obstruction within
5. Return the dry dust filter
and align vent cover
6. Push vent cover down
until it locks securely
1
1. Insert a small and thin tool into the pinhole
2. Push firmly until it clicks and/or the vent
cover pops out
3. Remove the dust filter, wash clean and dry
8.4 Out-vent
Vacuum the in-vent carefully, use a cotton
bud to remove dirt and dust from between the
vents.
8.3 In-vent
Use a slightly damp cloth to wipe clean any
blemish or dirt on the surface.
8.2 Surfaces
Before cleaning please Turn Off.
1. Surfaces: Slightly damp cloth
2. In-vent: Cotton bud & vacuum
3. Out-vent: Wash dust filter & vacuum
8.1 Cleaning recommendation
1
2
3
CAUTION: Replacing the Li-ion battery
incorrectly will severely damage your Air Halo.
To replace the rechargeable Li-ion battery:
8.5 Battery Replacement
Damaged Li-ion battery should be recycled or
disposed separately from household waste.
Maintenance repair by user is not advised.
For more details please see: 11.1 Warranty
• Model: AH01
• Power Mode: Silent / Normal / Boost
• Weight: 325g
• Air Sanitizer Technology: Plascide reactors
• Recommend Usage: 1m3
•
• Li-ion Battery: 18650 (cylinder-type)
• Dimension: 183mm (H), 63mm–83mm (W),
34mm–63mm (D)
8.7 Repair
8.6 Battery Disposal
1. Unscrew the
fastener
2. Remove the
battery cover
3. Replace battery
with Positive
end facing
downwards
4. Re-fasten the
battery cover
6.4 Charging
2.1A
8.5 Battery
Replacement
11.1 Warranty
10.1 Diagnostic
• Air Halo is covered by a manufacturer
guarantee and warranty
• Self-repair and/or signs of tampering will
void the warranty
• Repairs should only be carried out by a
certified person
• Please refer to the included warranty card
for more details
11.1 Warranty
If your warranty card or any accessories are
missing, please contact your nearest service
centre or alternatively contact the main office:
TEL:
FAX:
EMAIL: cs@a-onetech.com.hk
WEB: www.a-onetech.com.hk
11.3 Contact
11.2 Support
For all the latest Air Halo’s documentation,
please visit the support webpage:
www.a-onetech.com.hk/en-downloads
This device complies with Part 15 of the FCC Rules
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operations.
CAN ICE-3 (B)/NMB-3(B)
INSTRUCTION MANUAL
PORTABLE AIR SANITIZER
PLEASE READ THIS MANUAL BEFORE USE
M
EN
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.

2
3
4
5
4. Vacuum clean any dust
or obstruction within
5. Return the dry dust filter
and align vent cover
6. Push vent cover down
until it locks securely
1
1. Insert a small and thin tool into the pinhole
2. Push firmly until it clicks and/or the vent
cover pops out
3. Remove the dust filter, wash clean and dry
8.4 Out-vent
Vacuum the in-vent carefully, use a cotton
bud to remove dirt and dust from between the
vents.
8.3 In-vent
Use a slightly damp cloth to wipe clean any
blemish or dirt on the surface.
8.2 Surfaces
Before cleaning please Turn Off.
1. Surfaces: Slightly damp cloth
2. In-vent: Cotton bud & vacuum
3. Out-vent: Wash dust filter & vacuum
8.1 Cleaning recommendation
1
2
3
CAUTION: Replacing the Li-ion battery
incorrectly will severely damage your Air Halo.
To replace the rechargeable Li-ion battery:
8.5 Battery Replacement
Damaged Li-ion battery should be recycled or
disposed separately from household waste.
Maintenance repair by user is not advised.
For more details please see: 11.1 Warranty
• Model: AH01
• Power Mode: Silent / Normal / Boost
• Weight: 325g
• Air Sanitizer Technology: Plascide reactors
• Recommend Usage: 1m3
•
• Li-ion Battery: 18650 (cylinder-type)
• Dimension: 183mm (H), 63mm–83mm (W),
34mm–63mm (D)
8.7 Repair
8.6 Battery Disposal
1. Unscrew the
fastener
2. Remove the
battery cover
3. Replace battery
with Positive
end facing
downwards
4. Re-fasten the
battery cover
6.4 Charging
2.1A
8.5 Battery
Replacement
11.1 Warranty
10.1 Diagnostic
• Air Halo is covered by a manufacturer
guarantee and warranty
• Self-repair and/or signs of tampering will
void the warranty
• Repairs should only be carried out by a
certified person
• Please refer to the included warranty card
for more details
11.1 Warranty
If your warranty card or any accessories are
missing, please contact your nearest service
centre or alternatively contact the main office:
TEL:
FAX:
EMAIL: cs@a-onetech.com.hk
WEB: www.a-onetech.com.hk
11.3 Contact
11.2 Support
For all the latest Air Halo’s documentation,
please visit the support webpage:
www.a-onetech.com.hk/en-downloads
This device complies with Part 15 of the FCC Rules
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operations.
CAN ICE-3 (B)/NMB-3(B)
INSTRUCTION MANUAL
PORTABLE AIR SANITIZER
PLEASE READ THIS MANUAL BEFORE USE
M
EN
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.

2
3
4
5
4. Vacuum clean any dust
or obstruction within
5. Return the dry dust filter
and align vent cover
6. Push vent cover down
until it locks securely
1
1. Insert a small and thin tool into the pinhole
2. Push firmly until it clicks and/or the vent
cover pops out
3. Remove the dust filter, wash clean and dry
8.4 Out-vent
Vacuum the in-vent carefully, use a cotton
bud to remove dirt and dust from between the
vents.
8.3 In-vent
Use a slightly damp cloth to wipe clean any
blemish or dirt on the surface.
8.2 Surfaces
Before cleaning please Turn Off.
1. Surfaces: Slightly damp cloth
2. In-vent: Cotton bud & vacuum
3. Out-vent: Wash dust filter & vacuum
8.1 Cleaning recommendation
1
2
3
CAUTION: Replacing the Li-ion battery
incorrectly will severely damage your Air Halo.
To replace the rechargeable Li-ion battery:
8.5 Battery Replacement
Damaged Li-ion battery should be recycled or
disposed separately from household waste.
Maintenance repair by user is not advised.
For more details please see: 11.1 Warranty
• Model: AH01
• Power Mode: Silent / Normal / Boost
• Weight: 325g
• Air Sanitizer Technology: Plascide reactors
• Recommend Usage: 1m3
•
• Li-ion Battery: 18650 (cylinder-type)
• Dimension: 183mm (H), 63mm–83mm (W),
34mm–63mm (D)
8.7 Repair
8.6 Battery Disposal
1. Unscrew the
fastener
2. Remove the
battery cover
3. Replace battery
with Positive
end facing
downwards
4. Re-fasten the
battery cover
6.4 Charging
2.1A
8.5 Battery
Replacement
11.1 Warranty
10.1 Diagnostic
• Air Halo is covered by a manufacturer
guarantee and warranty
• Self-repair and/or signs of tampering will
void the warranty
• Repairs should only be carried out by a
certified person
• Please refer to the included warranty card
for more details
11.1 Warranty
If your warranty card or any accessories are
missing, please contact your nearest service
centre or alternatively contact the main office:
TEL:
FAX:
EMAIL: cs@a-onetech.com.hk
WEB: www.a-onetech.com.hk
11.3 Contact
11.2 Support
For all the latest Air Halo’s documentation,
please visit the support webpage:
www.a-onetech.com.hk/en-downloads
This device complies with Part 15 of the FCC Rules
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operations.
CAN ICE-3 (B)/NMB-3(B)
INSTRUCTION MANUAL
PORTABLE AIR SANITIZER
PLEASE READ THIS MANUAL BEFORE USE
M
EN
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.

2
3
4
5
4. Vacuum clean any dust
or obstruction within
5. Return the dry dust filter
and align vent cover
6. Push vent cover down
until it locks securely
1
1. Insert a small and thin tool into the pinhole
2. Push firmly until it clicks and/or the vent
cover pops out
3. Remove the dust filter, wash clean and dry
8.4 Out-vent
Vacuum the in-vent carefully, use a cotton
bud to remove dirt and dust from between the
vents.
8.3 In-vent
Use a slightly damp cloth to wipe clean any
blemish or dirt on the surface.
8.2 Surfaces
Before cleaning please Turn Off.
1. Surfaces: Slightly damp cloth
2. In-vent: Cotton bud & vacuum
3. Out-vent: Wash dust filter & vacuum
8.1 Cleaning recommendation
1
2
3
CAUTION: Replacing the Li-ion battery
incorrectly will severely damage your Air Halo.
To replace the rechargeable Li-ion battery:
8.5 Battery Replacement
Damaged Li-ion battery should be recycled or
disposed separately from household waste.
Maintenance repair by user is not advised.
For more details please see: 11.1 Warranty
• Model: AH01
• Power Mode: Silent / Normal / Boost
• Weight: 325g
• Air Sanitizer Technology: Plascide reactors
• Recommend Usage: 1m3
•
• Li-ion Battery: 18650 (cylinder-type)
• Dimension: 183mm (H), 63mm–83mm (W),
34mm–63mm (D)
8.7 Repair
8.6 Battery Disposal
1. Unscrew the
fastener
2. Remove the
battery cover
3. Replace battery
with Positive
end facing
downwards
4. Re-fasten the
battery cover
6.4 Charging
2.1A
8.5 Battery
Replacement
11.1 Warranty
10.1 Diagnostic
• Air Halo is covered by a manufacturer
guarantee and warranty
• Self-repair and/or signs of tampering will
void the warranty
• Repairs should only be carried out by a
certified person
• Please refer to the included warranty card
for more details
11.1 Warranty
If your warranty card or any accessories are
missing, please contact your nearest service
centre or alternatively contact the main office:
TEL:
FAX:
EMAIL: [email protected]
WEB: www.a-onetech.com.hk
11.3 Contact
11.2 Support
For all the latest Air Halo’s documentation,
please visit the support webpage:
www.a-onetech.com.hk/en-downloads
This device complies with Part 15 of the FCC Rules
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operations.
CAN ICE-3 (B)/NMB-3(B)
INSTRUCTION MANUAL
PORTABLE AIR SANITIZER
PLEASE READ THIS MANUAL BEFORE USE
M
EN
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Table of contents
Other A-oneTech Accessories manuals