AAMP Global EchoMaster Pro FC-GMHD102-MC User manual
Installation Guide
FC-GMHD102-MC
FC-GMLD102-MC
Integrated Blindspot Safety System
Select 2015-2018 GM vehicles with 7” radio display
Illustrations are typical and may not match exact vehicle details
2
Installation Guide
Illustrations are typical and may not match exact vehicle details
tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast)
Cover all surfaces with tape or plastic protection lm to protect against
scratching and damage. EchoMaster is in no way responsible for any damage
that may incur during installation.
This product has been validated in the vehicles listed on the application guide only.
Care must be taken when installing this accessory to ensure damage does not occur
to the vehicle. The installation of this accessory should follow approved guidelines to
ensure proper installation. Read entire instructions thoroughly before starting.
This document covers such items as:
- Vehicle Protection (use of covers and blankets, cleaning chemicals, etc).
- Vehicle Disassembly / Reassembly (panel removal, part storage, etc).
- Electrical Component Disassembly / Reassembly (battery disconnection,
connector removal, etc).
NOTES:
Removed Parts: Inspect the vehicle and parts for any damage.
Place all removed parts on a protected surface in an area where they will not get
damaged.
Connectors: When disconnecting connectors, do not pull on the wires; pull by
holding the connectors.
Retains the factory reverse camera if equipped.
Prior to Installation
FC-GMHD102 / FC-GMLD102
Integrated Safety System
3
Installation Guide
Illustrations are typical and may not match exact vehicle details
tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast)
Illustrations are typical and may not match exact vehicle details
CAUTION
It is recommended to perform this installation with the vehicle’s battery disconnected.
Please consult the vehicle’s owner’s manual for proper battery disconnection
procedure. Do not disconnect ANY airbag connectors or indicators. Doing so may
result in activating a diagnostic code. These codes will require the dealer to perform
the reset procedure which may incur a reset fee. If you are unsure of any vehicle trim
removal process consult the OEM service manual.
Removing vehicle trim panels in extreme hot and/or cold climate could result in
damage. Use care when removing all vehicle trims.
Using painter’s blue tape on the vehicle trim panels can help limit any scratches
and/or marring. Use a nylon trim panel removal tool whenever possible.
FC-GMHD102 / FC-GMLD102
Integrated Safety System
Vehicle Preparation & Protection
Suggested Tools
Painters Tape
Illustrations are typical and may not match exact vehicle details
4
Installation Guide
Illustrations are typical and may not match exact vehicle details
tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast)
Removing the Radio
Step 1
Using a nylon trim removal tool, remove the
LCD display trim panel.
Step 2
Remove the 4 x 7mm bolts from around the
LCD display.
Once bolts have been removed, remove the
unit from the dash.
Step 3
Disconnect the 4 connectors from the back
of the LCD display assembly and set aside.
FC-GMHD102 / FC-GMLD102
Integrated Safety System
5
Installation Guide
Illustrations are typical and may not match exact vehicle details
tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast)
Illustrations are typical and may not match exact vehicle details
FC-GMHD102 / FC-GMLD102
Integrated Safety System
Removing the Door Panel(s)
Step 1
Remove the plastic cover from the door
pull and remove the 2 x 7mm bolts.
Step 2
Remove the plastic cover from the door
release handle and remove the 1 x 7mm
bolt underneath.
Step 3
Remove the 2 x 7mm bolts from the
bottom of the door panel.
Illustrations are typical and may not match exact vehicle details
6
Installation Guide
Illustrations are typical and may not match exact vehicle details
tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast)
Step 4
Using a nylon trim removal tool, unsnap
the 4 clips and remove the plastic trim from
the armrest and set aside. Once the trim
is removed, remove the 7mm bolt found
underneath the trim.
Step 5
Pulling straight forward, not UP to release
all the clips, clips along the window are
metal and very tight. The clips around the
door panel are plastic.
Step 6
Release red lock tab from door wiring
harness to unlock door harness
connector.
Disconnect the harness.
Top clips are very tight.
WARNING
Removing the Door Panel(s) - continued
FC-GMHD102 / FC-GMLD102
Integrated Safety System
7
Installation Guide
Illustrations are typical and may not match exact vehicle details
tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast)
Illustrations are typical and may not match exact vehicle details
FC-GMHD102 / FC-GMLD102
Integrated Safety System
Step 7
Unclip door handle release assembly by
pressing on top and removing cable from
handle assembly. Set the door panel aside.
Repeat the steps above for the opposite
door panel.
Step 8
Remove plastic window bezel by removing
two plastic push pins and one clip
located in sail panel. Set plastic window
bezel aside.
Repeat steps for opposite side door.
Removing the Door Panel(s) - continued
Illustrations are typical and may not match exact vehicle details
8
Installation Guide
Illustrations are typical and may not match exact vehicle details
tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast)
Step 2
Disconnect the mirror assembly from door and
remove three harness fasteners.
Remove 3 x 10mm nuts from mirror
assembly (some models have 3 x 10mm bolts).
Remove mirror from door and set aside.
Take care not to scratch door when removing.
Mirror has one plastic clip securing it to door
frame. Medium force required to remove mirror
assembly from door.
Repeat for other side
WARNING
Step 1
Using nylon trim removal tool remove top arm
cover of mirror assembly.
Removing the Heavy Duty Mirror
Fully extend the mirror for removal and camera
installation.
PLEASE NOTE
Separate the camera mini connector from the
small power supply to route through the
mirror. Pull apart to separate reconnect
inside the door panel.
PLEASE NOTE
Heavy Duty Mirror
FC-GMHD102 / FC-GMLD102
Integrated Safety System
9
Installation Guide
Illustrations are typical and may not match exact vehicle details
tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast)
Illustrations are typical and may not match exact vehicle details
FC-GMHD102 / FC-GMLD102
Integrated Safety System
Step 3
Using a nylon trim removal tool remove the
bottom mirror cap from the mirror
assembly.
Using two nylon tools to work the cover
off is recommended. Be sure not to scar
plastic from mirror assembly.
PLEASE NOTE
Installing Mirror Pod Assembly
Using a zip tie taped to the camera
harness route wire from bottom of mirror
through the mirror and out the top.
Route the camera harness alongside the
factory wiring and secure with zipties.
Snap EchoMaster mirror pod cap on
mirror assembly.
Re-install mirror onto vehicle.
Illustrations are typical and may not match exact vehicle details
10
Installation Guide
Illustrations are typical and may not match exact vehicle details
tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast)
FC-GMHD102 / FC-GMLD102
Integrated Safety System
Using a nylon trim removal tool remove the mir-
ror cap from the mirror assembly.
There are 6 tabs holding the mirror cap on to the
mirror.
Press the pry tool in between the rear
cover and the front trim.
Pry the two pieces apart releasing the locking
tabs.
Using two nylon tools to work the cover
off is recommended. Be sure not to scar
the plastic on the mirror assembly.
PLEASE NOTE
Light Duty Mirror
Removing the Light Duty Mirror
11
Installation Guide
Illustrations are typical and may not match exact vehicle details
tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast)
Illustrations are typical and may not match exact vehicle details
Light Duty Mirror
FC-GMHD102 / FC-GMLD102
Integrated Safety System
Routing the Camera Harness
Route the camera
harness into the small
opening on the mirror
towards the large
opening.
Route the camera
harness in to the channel
towards the hinge where
the mirror mounts.
Route the camera
harness to the
opening in the hinge. There
is a large hole that the cam-
era harness will be routed
through.
Using a zip tie tapped to the
camera harness route the
wire down through the hole
in the hinge.
Route the camera
harness alongside the
factory wiring harness and
secure with zip ties.
Snap the EchoMaster
mirror cap onto the mirror
assembly. Make sure the
camera cable is in upper
corner closest to mirror.
Be sure ALL the locking tabs have
engaged
PLEASE NOTE
Illustrations are typical and may not match exact vehicle details
12
Installation Guide
Illustrations are typical and may not match exact vehicle details
tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast)
FC-GMHD102 / FC-GMLD102
Integrated Safety System
Route Camera Extension Harness
Starting from inside door, route the female end of the cable through the round factory
grommet (must cut hole).
Route the cable through the rubber door boot (easily done using a long zip tie taped
to harness). The wire should pass into the car below the factory door connector.
Route the cable under the dash to the appropriate connector on the main harness
extension.
Use zip ties to secure wiring.
Be sure to align the connector the
correct way, failure to do so will
result in damage.
WARNING
Use Caution when feeding the 4 PIN
connector through the boot. As to not
damage the connector or wires.
CAUTION
13
Installation Guide
Illustrations are typical and may not match exact vehicle details
tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast)
Illustrations are typical and may not match exact vehicle details
FC-GMHD102 / FC-GMLD102
Integrated Safety System
Route Camera Extension Harness
Route 16-pin main camera extension
cable down below the dash.
This should pass through hole located in
the back portion of the radio cavity and
exit from bottom of dash.
For vehicles with a center council, route
the camera harness towards the glove
compartment opening.
Camera 1 = Left Camera
Camera 2 = Right Camera
Camera 3 = Trailer Camera
Camera 4 = Optional Camera
Camera 4 input is automatically activated
when vehicle is in reverse gear when
aftermarket camera option is selected in
the installer menu.
Mount Module to Bracket
Mount module to bracket using the four
provided M3 screws.
Use zip ties to secure wiring to the bracket
Illustrations are typical and may not match exact vehicle details
14
Installation Guide
Illustrations are typical and may not match exact vehicle details
tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast)
Module Connections
Connect 8-pin power t-harness to module.
Connect 16-pin main camera extension
cable to module. Fasten harnesses to the
bracket using zip ties through the holes provid-
ed.
Select vehicle year using dip switches.
u 2018 dip switch 1 down
2 up
3 up
4 up
u 2017 dip switch 1 up
2 down
3 up
4 up
u 2015-2016 dip switch 1 up
2 up
3 up
4 up
Mounting the Module
Place in radio cavity and secure module/bracket
assembly in place using 2 x 7mm bolts (bolts not
included)
FC-GMHD102 / FC-GMLD102
Integrated Safety System
15
Installation Guide
Illustrations are typical and may not match exact vehicle details
tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast)
Illustrations are typical and may not match exact vehicle details
Remove GREY connector from behind
the radio display panel. Flip connector
over to access the bottom row.
Release the locking TABS on the
left and right side of the connector.
Fold locking TAB up.
Remove Green wire with white stripe
located in PIN 19. Fold the wire up againt the harness
and tape to protect it. Close locking
TAB and snap closed. Reconnect to
the radio display.
Bottom side of the connector
FC-GMHD102 / FC-GMLD102
Integrated Safety System
Illustrations are typical and may not match exact vehicle details
16
Installation Guide
Illustrations are typical and may not match exact vehicle details
tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast)
FC-GMHD102 / FC-GMLD102
Integrated Safety System
LVDS Connection
Re-install
Reinstall all removed panels and test system.
Press and hold the ‘‘HOME” button for three seconds
to enter the camera menu.
Disconnect the Grey and Gold con-
nector from the radio module along
with the BLACK LVDS connector
with the BLUE cable.
Connect the Grey and Gold connector
T-harness to the radio module and the
radio harness.
Connect the loose male LVDS connector into
female EchoMaster connector. Connect the male
EchoMaster LVDS connector into the radio
module.
The camera menu is accessible after 7 seconds while in reverse. Press and hold
the “HOME” button to access camera menu.
PLEASE NOTE
17
Installation Guide
Illustrations are typical and may not match exact vehicle details
tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast)
Illustrations are typical and may not match exact vehicle details
FC-GMHD102 / FC-GMLD102
Integrated Safety System
Wiring Diagram
Part No Description Qty
1 GMS-BYOM Main Interface module 1
2 GMSWRBRKT-1 Main Interface Bracket 1
3 BSM2-PTH Power T-Harness 1
4 BSM1-CEH Main Camera Extension Harness 810mm 1
5 BSM1-SCEH 1524mm/60” Side camera extension harness 2
6 CAM-EXT4PRCA-HAR Universal 4 pin Molex to RCA for camera 2
Part No Part No
GM1500-V2 LD Mirror caps with camera
and power supply
P-GM2500-V4 HD Mirror caps with camera
and power supply
Service Parts
Illustrations are typical and may not match exact vehicle details
18
Installation Guide
Illustrations are typical and may not match exact vehicle details
tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast)
FC-GMHD102 / FC-GMLD102
Integrated Safety System
Press and hold the ”HOME” button for three seconds to enter the camera
menu.
Use the touch screen select your desired view.
Press “HOME” to return to the previous screen.
The camera menu is accessible after 7 seconds while in reverse.
Press and hold the “HOME” button to access.
PLEASE NOTE
To Access the Menu
19
Installation Guide
Illustrations are typical and may not match exact vehicle details
tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast)
Illustrations are typical and may not match exact vehicle details
FC-GMHD102 / FC-GMLD102
Integrated Safety System
Activating NON-Factory Backup Camera option
From the main camera menu
From the main camera menu press and hold the on the lower right hand corner
of the screen.
Installer setup screen select Enable Aftermarket Backup Camera if no factory back up
camera installed.
15500 Lightwave Drive, Suite 202, Clearwater, Florida 33760
Unit 25B, Woolmer Way, Bordon, Hampshire, United Kingdom, GU35 9QE
tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast)
tel - +44(0)1420 487110 (sales) - +44(0)1420 470618 (technical)
EchoMaster is a Power Brand of AAMP Global.
EchoMaster.com
AGREEMENT: End user agrees to use this product in compliance with the instructions and terms of
use above and with all State and Federal laws. EchoMaster provides instructions and safety warnings
with respect to this product and disclaims all liability for any use not in conformity with those
instructions or other misuse of its product. If you do not agree, please discontinue use immediately
and contact EchoMaster. This product is intended for off-road use and passenger use only.
IUG-FC-GMHDLD102-MC
REV. 032818
This manual suits for next models
1
Table of contents
