AAXA Technologies HP3 Halloween Projector User manual

aaxa
TECHNOLOGIES
User Guide
HP3 Halloween Projector

Caution!
WARNING: Please use this product as instructed. Misuse may cause
injury or death.
DO NOT use while driving
DO NOT expose to water or wet surfaces. Electric shock may occur
DO NOT expose the projected LED image to your eyes or the eyes of others
DO NOT block or restrict airow from ventilation holes as this may cause the
projector to overheat
Keep the projector, battery, or charger away from any heat sources

Table of Contents
Chapter 1: HP3 at a Glance
HP3 Introduction
Remote & KeypadRemote & Keypad
Accessories
Chapter 2: Getting Started
Powering On / O󰀨
Focus Adjustment / Throw Distance
Connecting to Speaker/ Headphone
Loading External Content
Keystone & Projection Direction
Chapter 3: Menu Screens
Main Menu
Halloween E󰀨ects Menu
Files Menu
Connecting via Digital Input
Chapter 4: Settings Menu
Picture Menu
Sound Menu
Options Menu
Chapter 5: Technical Details
Troubleshooting
Specication
Notes
1
2
3
4
5
6
7
9
11
12
13
15
18
19
20
21
22
25
26

HP3 at a Glance
1
Chapter 1
Digital AV
(HDMI Compatible)
Main Unit
Keystone
Adjustment
TF Card
Headphone Out
D/C Power
Power Button
Vent Fan Standard USB 2.0
Compatible
Focus Adjustment
Composite AV

Remote & Keypad
2
Power On/O󰀨
Select Source
Conrm
Left
Both the keypad and remote can be used to navigate through the menus. The Main Menu
Navigation on the remote functions exactly the same as the directional pad on the HP3 unit.
Navigation
Volume Up
Volume Down
Remote
Home
Mute
Return
Navigation Pad
Right Return
Home Power
On/O󰀨
Settings Menu

Accessories
3
*Under various circumstances, the actual accessories may be dierent from
those shown in the pictures above.
Additional accessories are available for purchase at www.aaxatech.com
Power Cable Remote Preloaded
TF Card

Getting Started
1. Connect the power cord to the HP3.
2. Connect the other end of the power cord into the wall power source.
3. Press the On/O󰀨 button at the top of the HP3 for about 3 seconds, wait shortly
and the projector should automatically boot up and turn on. You can also press the
Power On/O󰀨 button on the Remote Control to power on the projector.
4
Powering ON the projector
Chapter 2
Powering OFF the projector
1. To turn o󰀨 the projector, press the “On/O󰀨” button on the navigation pad on top of
the projector or the remote control.This will fully turn o󰀨 the projector.
2. Unplug and disconnect the HP3 from the power source
Standby Mode
1. To transite to “STANDBY MODE”, press the power button on the remote control.
2. The optical engine should power o󰀨 and the fan should stop spinning. The projector
is now in “STANDBY MODE” and can be turned on using the remote control.

Focus Adjusment / Throw Distance
5
DIAGONAL SCREEN SIZE
16:9 Aspect Ratio
Throw Distance
Units: Inches
25
30
40
50
60
70
80
90
Diagonal Screen
Units: Inches
20
25
33
41
49
57
66
74
• Spin the focus wheel up or down
until the image becomes clear.
Focus Adjustment
Throw Distance Chart
Throw Ratio 1.4:1
Projection Angle: 0% O󰀨set
*minimum throw distance: 25 inches

Connecting Speakers / Headphones
Connect your speakers/headphones
to the projector’s audio port.
Step 1:
Step 2:
*CAUTION: Prolonged use of headphones at a high
volume may impair hearing.
Ensure that the projector and/or the
headphones are powered on.
Step 3: Place the headphones on and enjoy!
6

7
Loading External Content
The HP3 can read les directly from
both a TF Card and USB Drive.
Supported le types include:
AVI / MP4 / JPG
(up to 64 GB)
(up to 64 GB)

Loading External Content Cont.
How to insert your TF Card
• Slide in your TF card into the TF card
slot on the side of the HP3 (as shown
in picture).
• Gently slide the TF card until it clicks
into place.
8
(up to 64 GB)

9
Keystone Adjustment
What is Keystoning?
“Keystoning” occurs when a projector is aligned non-perpendicularly to a screen,
or when the projection screen has an angled surface. The image that results
from one of these misalignments will look trapezoidal rather than square.
Keystone Adjustments
By adding a special, selectable algorithm to the scaling, some new projectors are
able to alter the image before it reaches the projection lens. The result is a squared
image, even at an angle.

Keystone Adjustment
10
How to Correct Keystone
• If the image looks trapezoidal with the
base or the top larger, use the Key-
stone Adjustment wheel on the top of
the HP3 projector to adjust the image
until the projection screen is a squared
image.

Menu Screens
11
Chapter 3
Main Menu
The HP3 features an Onboard Media Player.
To play videos, pictures, and music les directly from your connected devices, go to the
“Projector Functions” in the Main Menu.
• Press the left and right directional buttons to choose an icon from the main menu.
• To select a menu option, press the “OK” button in the navigation pad.
• To go back to the previous screen, press the “Back” button.
• To return to the main menu, press the “Home” button.

Halloween Effects Menu
To play special Halloween e󰀨ects:
• Select the “Halloween Video Player” icon (Fig. 3.1) in the Main Menu then
choose the your preferred e󰀨ects in the “Video Player Menu” (Fig. 3.2)
• Select “Play Single Video” if you wish to play an e󰀨ect in loop mode.
Select “Play All Videos” if you wish to play all 6 e󰀨ects. (Fig 3.3)
12
Fig. 3.1 Fig. 3.2
Fig. 3.3

13
Opening A File:
• Select the “Projector Function” icon in the Main Menu ( Fig 3.4)
• In the “Functions Menu”, select the “Video” or “Photo” icon ( Fig 3.5)
Fig. 3.4 Fig. 3.5
Files Menu

The HP3 will show all folders and les you have on your USB or TF Card drive.
Use the navigation buttons on the navigation pad or the remote control to select
folders or les.
14
Files Menu
Navigation

Connecting to Device via Digital Input
15
Connectivity to Multimedia Devices
The HP3 can connect to many media devices including: computers, laptops,
iPhones, iPads, DVD players, smart phones, cameras, video game consoles
and other peripherals with ease. The HP3’s digital input is compatible with HDMI
interface. The connection type is “full sized”.
*Some smartphones require video out capabilities to be displayed with the HP3. Check with your phone manufacturer.
In the Functions Menu
Select the “Inputs” Icon Then select the “Digital Video” Icon
First, a digital input cable is required from your HP3 to your other device.

Connecting to Digital Input Video Devices
16
Connect one end of the Digital Input Cable to
your device’s Digital Input port.
Step 1:
Step 2:
Step 3:
In the Main Menu, select the “Digital Video” Icon. Your HP3 should now
be mirroring the content from your device.
Connect the other end of the Digital Input
Cable to your HP3’s Digital Input port.
If you’re connecting to a computer or laptop and the projector does not
automatically mirror it, read onto the next page for more information.
Note:

17
Connecting to a Computer via Digital Input
After connecting your projector to your computer or laptop via a digital input cable, you may need
to enabe Digital Video output on your computer. To enable Digital Video output on your computer
most computers require “turning on” the video output feature. Each computer is di󰀨erent. Please
consult your owner’s manual for instructions to enable Digital Video output. Below are standard
instructions for a Windows 10 computer – not all systems are the same.
Press Windows+P to toggle
through display settings. Select
either “Duplicate” or “Extend” de-
pending on your viewing option.
*NOTE: Dierent operating sys-
tems may dier
Step 5: 1. Right click on computer
desktop and select “Screen
Resolution.”
2. Display Properties window
will pop up and select the
Advance Display Settings.
3. Please make sure the “Mul-
tiple displays” has the “Dupli-
cate these displays” option
selected and the Resolution
is 1920 x 1080 or below as
pictured in the red box.
4. If the image is blurry or the
text is not legible, adjust the
screen resolution.
Step 6:
Step 4: