AAXA Technologies M4 User manual

aaxa
TECHNOLOGIES
User Guide
M4Pico Projector

Caution!
WARNING: Please use this product as instructed. Misuse may cause
injury or death.
DO NOT use while driving
DO NOT expose to water or wet
surfaces. Electric shock may occur.
DO NOT expose the projected LED
image to your eyes or the eyes of
others
DO NOT block or restrict airow
from ventilation holes as this may
cause the projector to overheat
Keep the projector, battery, or
charger away from any heat sources
Caution for Battery Use
• Do not pierce or puncture the battery
with sharp objects
• Do not heat the product or expose it to
high temperature.
• Do not wet it or place it in any liquid
Caution for Headphone Use
• Prolonged use at high volume may
impair your hearing.
• High volume during walking or driving
may cause distractions and result in
injury or death

Table of Contents
1
2
3
4
5
6
7
8
Connecting a Micro SD Card
Connecting to a USB Host
Chapter 3: Menu Screens
Chapter 4: Technical Details
Troubleshooting
Specications 1
Chapter 1: M4 at a glance
Main Unit Front/Back
Remote & Keypad
Accessories
Main menu
Video Player Menu
Video FAQ
Photo Viewer Menu
Photo FAQ
Music Player Menu
Music FAQ
Setup Menu
Keystone Adjustments
Connecting to Speaker or
Headphones
Chapter 2: Getting Started
Powering On / OFF
FocusAdjustment/Throw
Distance
Battery Pack Information
Connecting to a Computer VGA
Connecting to a Computer HDMI
Connecting to HDMI Video
DTV Setup
10
12
14
17
18
20
22
23
25
26
28
29
31
32
39
41

2
Chapter 1
Power On/Off
Main Menu
Navigation
Main Unit Front/Back Power Button
M4 at a Glance
Power Switch
Focus Wheel
Component Port
MicroSD Card Slot
HDMI Input
USB
TV Antenna
3.5mm Audio DC Adapter
VGA

PWR Gamma
ME
NU U
UP EXIT
VOL-
OK
VOL+
I
U/D DOWN R/L
VGA Menu AV
Menu
Remote & Keypad
3
Power On/Off
Select Source
Media Player Menu
Navigation
Input Exit/Back
Direction Pad
LED Lights
Keystone Adjustment Keystone Adjustment
Main Menu Navigation
Volume Adjustment Volume Adjustment
On / Off
Both the keypad and remote can be used to navigate through the menus. The Main Menu
Navigation on the remote functions exactly the same as the directional pad on the M4 unit
for all modes except DTV mode. In DTV mode the remote control is necessary to perform
the “scan” feature

Accessories
4
*Under various circumstances, the actual accessories may be different from
those shown in the pictures above.
PWR Gamma
MENU U
UP EXIT
VOL-
OK VOL+
I
U/D DOWN R/L
VGA Menu AV
Menu
Internal Battery
(pre-installed)
Remote
Power Adapter

Getting Started
5
Powering ON the projector
Chapter 2
Powering OFF the projector
Note: The M4 Projector battery does not charge when it is in operation. For first time
operation charge the battery for 120 minutes to ensure a full charge.
1. Connect the power adapter to the projector and power outlet
2. Switch the On / Off switch on the side of the projector to the “ON” position
There are two "idle" modes for the projector. "Off" and "Standby". The "Off"
mode complete turns off the projector. The "Standby" mode allows the projector
to be turned on with the remote control. The standby mode consumes a little
battery power when left in this mode.
1. To fully power off the projector, switch the On / Off switch on the side of the projector
to the "Off" position
2. To put the projector in "Standby" mode press the POWER button on the keypad
3. A window will pop up asking "Do you want to power off?"
4. Press the power button again to put the projector in "Standby" mode

Focus Adjusment / Throw Distance
Focus Adjustment
6
DIAGONAL SCREEN SIZE
16:9 Aspect Ratio
Throw Distance Chart
• Adjust the focus wheel left and right until the image
becomes clear.
Screen Size (Inch)
102
96
89
82
75
68
61
55
48
41
34
27
21
Distance (Meters)
3
2.8
2.6
2.4
2.2
2
1.8
1.6
1.4
1.2
1
0.8
0.6 Throw Ratio 1.360

7
1. Remove the three screws
circled in blue holding the M4
battery compartment.
2. Disconnect the battery harness
to the battery receptacle on the
PCBA
**Please notethat the battery pack is pre-installed in the M4. The instructions
below is how to remove the battery unit if replacement is needed.
3. Remove the battery and
replace with new battery unit
using previous instructions
in reverse order.
Battery Pack Installation

Connecting to a Computer via VGA
Connect the large end of the
8
VGA Cord
to your computer’s
VGA Adapter
Step 1:
Step 2:
Step 3:
In the Main Menu
Select “VGA” iconSelect “INPUT” icon
to your M4
VGA Cord
Connect the large end of the
VGA Adapter