Accell K072C-014B User manual
READ ME FIRST – SETUP INSTRUCTIONS
Thank you for purchasing the Accell UltraAV HDMI Distribution
Amplifier. This product is designed to provide an exceptional
performance and value. Please review the manual before
operating and retain for future reference.
- CAUTION -
1. Ensure the matrix and receivers
have sufficient ventilation. Do not
cover ventilation openings. Do not
install in a confined space.
2. Do not operate near source
of heat. Do not stack on top,
underneath or between other heat
generating unit/s including other
amplifiers.
3. Unplug power adapter if not
used for an extended period.
4. To prevent damage from power
surges, the unit should be plugged
into a surge protector or surge pro-
tected power source.
5. Do not use near liquid or areas
of heavy moisture.
6. Clean unit with a clean and dry
cloth only.
7. This unit cannot be serviced in
the field. Contact Accell if service is
required.
8. Do not open case, risk of shock -
shock hazard.
9. Do not modify power cord or use
the product if the power cord is
damaged.
Introduction
The UltraAV HDMI 4x4 Matrix and Distribution Amplifier featuring
HDBaseT accepts signals from up to 4 HDMI enabled audio/video sources
and distributes the signal to up to 4 HDMI enabled displays. The matrix
can be configured to send any input to any HDMI displays, monitors,
projectors or TV’s.
Over-Current and Over-Voltage Protection
The circuit boards are equipped with both over-current and over-voltage
protection and will automatically power down if encountered. The circuit
boards will restore automatically once the excessive current or voltage
has passed.
Package Contents
●HDMI Distribution Amplifier (Matrix) ●1 Power Adapter (for Matrix)
●4 HDBaseT Receivers ●4 Power Adapters (for Receivers)
●CD-ROM (for RS-232 control) ●4-Pair IR-TX and IR-RX
●Remote Control (with battery) ●Owner’s Manual
●2 Front Panel Mounting Ears (with 4 Screws)
Model Number:
K072C-014B
UltraAV
®
HDMI 4x4 Matrix
with HDBaseT
Setup
Note: All Cat5e/6 cables must be terminated to 568B standards.
Unsheilded (or properly terminated sheilded cable), solid core Cat5e,
Cat6, Cat6e, Cat7 or Cat7e cable can be used. Stranded core is not
suggested as it can reduce signal transfer. Recommended to use a
continuous length of cable terminated at the matrix and receiver ends.
With the matrix power switch in the OFF position, connect an HDMI High
Speed cable from the HDMI Output of the most commonly used audio/
video source to the HDMI Input 1 located on the rear of the matrix.
Similarly, connect the remaining source devices to the HDMI Input Ports
on the matrix.
Tips: Use the shortest length HDMI cables possible in each point
in the installation. Use only High Quality and High Speed HDMI
cables.
If desired, run a LAN cable from your network or router into the port
labeled LAN IN on the rear of the matrix.
Next, connect a Cat5e/6 cable to the HDBaseT Out 1 port on the rear of
the matrix. Connect the other end of the Cat5e/6 cable to the HDBaseT
IN port on the rear of the HDBaseT receiver positioned near the TV. Run
a short, High Speed HDMI cable from the HDMI Out port on the receiver
to the HDMI In port on the TV. If desired, two Ethernet ports are
provided on the rear of the receiver for connection to Internet enabled
TV and/or computer. Plug a provided power adapter into an AC outlet
and the other end into the HDBaseT receiver. Using the same steps,
connect the remaining audio/video sources to the matrix.
The matrix has internal memory that stores the system
information for faster switching. Please follow the steps in the
order listed: Turn ON the displays and ensure they are awake (not in
standby mode). Check the displays INPUT setting to ensure the correct
HDMI port is active.
Turn on the source devices and ensure they are awake (not in standby
mode). Connect the power adapter to the matrix. Plug the power
adapter into a surge protected AC power outlet. Turn the matrix power
switch to the ON position.
The matrix has a low power draw and is intended to be left on. If
the matrix is turned off, start up the system as noted above. If new
hardware is added, please perform a RESET.
To RESET the matrix, turn off the display and source devices. Power off
the matrix and unplug the power adapter from the rear of the matrix.
Wait 20 minutes for the memory of the system configuration inside of
the matrix to be deleted. Follow the setup instructions above to correctly
initiate the setup.
HDMI 4x4 Matrix and Distribution Amplifier
Model: K072C-014B
Specifications
● Independently access 4 HDMI Sources from 4 HDMI Displays
● Supports HD resolutions up to 1080P and 3D
● HDMI 1.4a, HDCP 1.2 compliant
● Audio formats supported: DTS-HD 7.1, Dolby True-HD 7.1
● Deep color up to 36-bit
● RS232 Port for control
● Maximum HDMI input/output cable length: Up to 16ft./5m
● Maximum Cat5e/6 output cable length: Up to 328ft./100m
● Supports up to 100 BaseT Ethernet, two ports per receiver
● 19” Rack Mounting (front panel mounting brackets included)
● 12V DC, UL Listed Power Supply for 4 x 4 Matrix Unit
● 5V DC, UL Listed Power Supplies for Receiver Units (4 Total)
● Matrix dimensions: 17.3”W x 2”H x 7.9”D (440W x 51H x 20D mm)
● Receiver dimensions: 4.4” W x .9” H x 3” D (112W x 23H x 76D mm)
● Operating temperature range: 5 to 131°F (-15 to 55°C)
● Operating humidity range: 5% to 90% RH (no condensation)
Infrared Control (IR)
Ultra-IR Receiver and
Transmitter Pin
Assignment
Ultra-IR Receiver (5 ft.)
Dual Frequency: 38KHZ-60KHZ
PN: B164B-002B
Ultra-IR Transmitter (5 ft.)
Dual Frequency: 38KHZ-60KHZ
PN: B164B-003B
Q. Get the message “This protocol is not supported” or other error message.
A. See answer A1 above and repeat the steps outlined.
Q. The matrix is not down sampling the video and some of the TV’s are not
displaying a picture.
A1. Go into the TV’s setup and configure the resolution to match all the
connected TV’s. The TV’s should share the same resolution.
A2. In the source devices menu options set the source device to output a
resolution that matches all the connected displays.
Q. My TV’s resolution are not optimized.
A. The matrix will query the displays and provide the highest common video
resolution amongst them. Example: Using a 1080p source, if 3 of the displays
support a maximum resolution of 1080p and 1 display supports a maximim
resolution of 720p, all 4 display will operate at a resolution of 720p. If the 720p
TV in the example is then turned off, the other 3 displays can then operate in
1080p resolution. Turn Off then turn On the matrix to refresh the configuration.
The three 1080p TV’s will refresh (flicker) then each will display a 1080p picture.
ASSISTANCE: Questions regarding this product or its product
warranty, please check out our Web site at: www.accellcables.com.
or phone at 510-438-9288, toll free 877-353-0772 (M-F 9am-5pm PST).
1-YEAR MANUFACTURERS WARRANTY
The Accell UltraAV Matrix is warranted for one year from date of
purchase to be free of defects in material and workmanship. In the event
of such defects, the Accell product will be repaired without charge or
replaced with a new one at our option, if delivered to Accell Corporation
prepaid, together with a copy of the sales receipt indicating the proof of
purchase date and place of purchase. This warranty excludes defects due
to normal wear, abuse, shipping damage, or failure to use the product
in accordance with the instructions. ACCELL CORPORATION SHALL NOT
BE LIABLE FOR DAMAGES BASED UPON INCONVENIENCE, LOSS OF
USE OF THE PRODUCT, LOSS OF TIME, INTERRUPTED OPERATION OR
COMMERCIAL LOSS, OR ANY OTHER DAMAGES, WHETHER INCIDENTAL,
CONSEQUENTIAL OR OTHERWISE. YOU AGREE THAT ACCELL’S MAXIMUM
LIABILITY ARISING FROM ANY PRODUCT SOLD BY ACCELL SHALL NOT
EXCEED THE PRICE OF SUCH PRODUCT. SOME JURISDICTIONS DO NOT
ALLOW THE LIMITATION OF EXCLUSION OF LIABILITY FOR CERTAIN
DAMAGES, SO THE ABOVE MAY NOT APPLY TO YOU TO THE EXTENT
SUCH JURISDICTION’S LAW IS APPLICABLE TO THIS AGREEMENT. This
warranty gives you specific legal rights, and you may have other rights
that vary from state to state.
LIMITATION OF LIABILITY
IN NO EVENT SHALL ACCELL CORPORATION, ITS SUBSIDIARIES
OR AFFILIATES, OR THEIR RESPECTIVE PARTNERS, OFFICERS,
DIRECTORS, EMPLOYEES, SHAREHOLDERS, REPRESENTATIVES OR
AGENTS (COLLECTIVELY, “ACCELL”) BE LIABLE FOR DIRECT, SPECIAL,
INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR INDIRECT DAMAGES
(INCLUDING BUT NOT LIMITED TO, LOSS OF DATA, USE OR PROFITS),
HOWEVER CAUSED, WHETHER FOR BREACH OF CONTRACT, NEGLIGENCE,
OR OTHERWISE, AND WHETHER OR NOT ACCELL HAS BEEN ADVISED
OF THE POSSIBILITY OF ANY SUCH DAMAGES. YOU AGREE THAT
ACCELL’S MAXIMUM LIABILITY ARISING FROM ANY PRODUCT SOLD
BY ACCELL SHALL NOT EXCEED THE PRICE OF SUCH PRODUCT. SOME
JURISDICTIONS DO NOT ALLOW THE LIMITATION OF EXCLUSION OF
LIABILITY FOR CERTAIN DAMAGES, SO THE ABOVE MAY NOT APPLY TO
YOU TO THE EXTENT SUCH JURISDICTION’S LAW IS APPLICABLE TO
THIS AGREEMENT.
WARRANTY RETURNS PROCEDURE
Contact Customer Support to obtain a Return Authorization (RMA)
number. RMA numbers are valid for 30 days from the date of issuance.
We are unable to accept returns without an RMA number. Returns
without an RMA number clearly printed on the outside of the package
will be refused and returned unopened. All returns must be shipped
prepaid at the expense of the shipper.
Accell assumes no responsibility for any inaccuracies and liability for
direct, indirect, special, incidental, or consequential damages as a result.
Due to ongoing improvements, Accell reserves the right to make changes
to hardware, packaging and any accompanying documentation without
prior written notice.
©2013 Accell Corporation, All Rights Reserved. Accell and UltraAV are
registered trademarks of Accell Corporation.
Support
RS-232 Control Port (4x4 HDMI Matrix)
The RS-232 port located on the 4x4 HDMI Matix provides control similiar
to the remote control from a remote device. A correctly configured
RS232 cable is required. Connect the RS232 cable end to your PC Serial
port (default =COM 1). The other end to HDMI Matrix RS232 port.
Place the included CD-ROM into your computer CD-ROM drive. Go to
the CD-ROM drive and double-click the “HDMI FamilySetupB.exe” file
to install the command configuration application. The HEX codes and
settings, RS-232 cable configuration as well as additional details on the
usage of the application are included in PDF file format on the CD. Open
the CD and locate the PDF file. To open/read use Adobe Acrobat Reader.
The 4x4 HDBaseT Matrix includes 4 pairs of Infrared Extenders, 4 IR
Transmitters (IR-TX) and 4 IR Receivers (IR-RX). The front panel of the
matrix has 4 IR-TX ports and 4 IR-RX ports. The HDBaseT Receivers each
have one IR-TX port and one IR-RX port. Using the included extenders
and appropriate IR port, you can choose to configure the IR to control
the source devices when positioned at the display or control the display
devices when postioned at the source.
To control multiple source devices with one IR-TX, stack the sources
together and position the IR-TX so that all the source devices can receive
the IR signal (Blast) from the IR-TX.
The port on the matrix labeled “IR Extender” accepts an optional IR
Receiver, taking commands from the included matrix remote control. This
receiver enables line-of-sight if the matrix with its built-in IR receiver,
labeled on the front panel as IR, is not visable.
LED indicator lights
On initial power on, all LED lights on the matrix should come on solid
blue. All the numerical LED displays will momentarily read ‘0’ and
then change to ‘1’. If less than the maximum number of Displays
are connected to the matrix (not all the outputs are used) the
numerical indicator will indicate ‘0’ for that output and there will be no
corresponding HDMI OUT blue LED for the unused output. Blue lights
will only appear for devices connected. Any unused HDMI Input ports will
also have its HDMI IN blue LED unlit.
The HDBaseT Receiver has 4 LED indicators:
1. HDCP: A solid LED indicates that the HDCP handshake between the
source and display has been authenticated.
2. Link: Indicates a connection between the Matrix and the Receiver.
3. Mode: A flashing LED indicates correct operation of the system.
4. Power: A solid LED indicates power to the receiver.
Operation
Manual Control: You can operate HDMI source switching manually by
using the buttons labeled ‘Out” located on the front panel. Press the
button that corresponds to the output that you want to change the HDMI
source on and toggle through until the desired HDMI input source video
is being displayed. A numerical LED indicates which HDMI source input is
being shown on each output (HDTV).
Remote Control: Included with the Matrix is a Remote Control. It can
control the matrix by pointing it at the front of the matrix, targeting
the integrated IR receiver labeled IR. IR uses line-of-sight between
the remote control (or IR-TX) and the receiver. The angle which the
remote will work is at about a 15° degree angle in either direction to the
receiver. If the receiver is postioned such that there is not line-of-sight,
the port labeled “IR Extender” accepts an optional IR Receiver. This
receiver enables line-of-sight if the matrix is out of position.
LED Indicator Lights Troubleshooting
A. One of the display does not show a picture or output audio.
Q. Check the displays input setting to ensure it is set to receive a signal from the
connected HDMI port.
Q. One or more of the connected displays will not display a picture while one or
more of the displays do display a picture:
A1. Turn off the power to the matrix, source and displays. Wait 1 minute. Turn
the source on. Turn the displays on. Turn the matrix on.
Other Accell Matrix Switcher manuals
