Shinybow USA SB-8811 User manual

INSTRUCTION MANUAL
MODEL : SB-8811
8x8 DVI MATRIX SWITCHER
8x8 DVI MATRIX SWITCHER
FULL HD DVI Matrix Switcher Series
Thank you for purchasing the SB-8811 DVI Matrix Switcher. You will find this unit easy to install and highly
reliable but it is essential that you read this manual thoroughly before attempting to use this switcher.
MULTIMEDIA AUDIO AND VISUAL

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualified service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualifier service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF AGENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL

TABLE OF CONTENTS
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow
for sufficient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update or
to keep current the information contained in this document.
We reserve the right to make improvements to this document and/
or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed,stored in aretrieval system,or anyof itspart translated
into any language or computer file, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise — without express written permission and consent
© Copyright 1997. All Rights Reserved.
Version 2.1 OCT 2013
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.
CONTENTS
INTRODUCTION ...............................................................1
FEATURES & SPECIFICATIONS...................................... 2
FRONT PANEL ................................................................ 3
REAR PANEL ................................................................ 6
REMOTE CONTROL ....................................................... 7
EDID FUNCTIONS ......................................................... 9
TYPICAL APPLICATION ............................................... 12
IR EXTENDER ............................................................... 14
RS-232 PROTOCOL .................................................... 15
LIMITED WARRANTY .................................................. 16
INTRODUCTION
The SB-8811 is high-performance 8x8 matrix routing switcher
for DVI (Digital Visual Interface) signals. This switcher supports
data rates up to 6.75 Gbps, enabling 1080p DVI formats and
UXGA/WUXGA/DVI resolution to any HD display. High Definition
Digital signals can be selected and distributed to any 8 outputs
simultaneously. The Switcher is certified as being fully DVI and
HDCP compliant, with RoHS,CE,FCC certification. Support high
resolution DVI sources routed to DVI displays, monitors, projector
or audio receivers. The EDID can be selected between seven (4)
different modes. Control is provided via front panel push buttons,
IR remote or via RS-232. An RS-232 Windows GUI interface is
provided for matrix routing.
PACKAGE CONTENTS
Check that you have the following components;
• SB-8811 Matrix Routing Switcher
• IR Remote Controller (SW-8811)
• 19 inch Ear mount bracket (Part # 1U-440L)
• IR Extender receiver (SB-100)
• CD Contents: This manual, Windows GUI
• RS-232 Cable
• Users Guide
• Power Supply: 12VDC, 5A Universal Type 50/60Hz, 100~230
VAC
1

FEATURES & SPECIFICATIONS
FEATURES
• 8x DVI digital source devices matrix switched to 8x DVI devices.
• DVI digital video w/embedded audio, DVI format and CEC/HDCP 2.0 compliant
• Seven (7) function key control and worldwide (4) EDID modes for HDTV resolutions.
• Link speeds of up to 6.75 Gbps (link clock rate of 340Mb Hz), Support DVI 3D formats.
• Wide range of HD resolutions from PC XGA to WUXGA 1920x1200 and HDTV/DTV resolutions 480i/480p, 576i/576p, 720p, 1080i
& 1080p
• Compatible with all DVI source devices, PC monitors, Plasma HD display, HDTV and audio receivers/amplifiers.
• Digital Video TMDS formats Resolution up to 1080p-60 with Deep color 36-bit.
• Various user interface controls:
• Windows-based GUI control via RS-232 port
• Front panel push buttons
• IR wireless remote control
• Third party RS-232 controller (via simple ASCII)
• Supports worldwide control functions: ALL/OFF/RECALL/ENTER/MEMORY/EDID/LOCK.
• Support EDID modes :
• Internal modes : AUTO/1080p-2CH/1080p-5.1/1080p-7.1/1080i-2CH/720p-2CH
• External modes : Passing mode
• Automatic scanning input & output status via LED show on front panel.
• Support preview output port simultaneously output #1.
• Support IR Remote and IR Extender with distance up to ~ 1000’ (300M) Maximum.
• EDID configuration via Internal modes.
• Consumer Electronic Control (CEC) switch all open or OFF
The Switcher will remember that last state during a power cycle.
When power is removed and resorted, the last configuration will be invoked.
SPECIFICATIONS
• Type of DVI Switcher: 8x DVI inputs To 8x Outputs DVI Matrix Switcher
• DVI Support: HD 1080p-@60Hz, H36-bit Deep color, 3D (1.4a) formats
• HDCP / CEC Support: HDCP 2.2 Compliant, CEC Compliant.
• Video Bandwidth: Double Data Rates: 340 MHz, total 6.75 Gbps bandwidth
• Digital Video Support: Full HD resolution : 480i / 480p / 720p / 1080i / 1080p
• Switcher Controls:
• IR remote control
• IR external port x 1 (OD 3.5mm ear phone jack)
• Select & Function buttons on front panel
• RS-232 serial interface
• Preview Output: Support 1x preview output port simultaneously via Output- #1
• Source Status: Automatically Scan Sources Inputs via LED
• Function Control Key: ALL / OFF / RECALL / ENTER / MEMORY / LOCK / EDID
• Infrared Frequency: 38 Khz
• IR External Distance: ~1000 feet / 300 meters maximum
• HDMI I/O Connector: DVI-D - (24+5) pin Female DIP Type
• Temperature: Operate in a place between 32°F - 100°F (0°C - 38°C)
• Dimensions (LxWxH): 19 x 9.85 x 1.75 in (482mm x 250mm x 44mm)
• Rack Mount: Rack Mount 1RU High 19 in Rack Mount (with rack mount)
• Power Supply: DC12V / 5A, Universal world wide Type 50/60Hz, 100~230 VAC
• Power Consumption: 3880 mA Maximum
• Safety Approvals: CE, FCC, RoHS (2002/95/EC)
• Product Weight: 13 lbs
As product improvements are continuous, specifications are subject to change without notice.
2

FRONT PANEL
FRONT PANEL
1. POWER SWITCH
The power switch turns the unit on and off. The LCM will illuminate red to indicate that the switcher is ON and is receiving power. The
Switcher will remember that last state during a power cycle. When power is removed and resorted, the last configuration will be evoked.
2. INPUT STATUS DISPLAY
Input sources 1 to 8 LCM illuminates blue to indicate that a video source is present on that input.
3. OUTPUT STATUS DISPLAY
Each Output (destination ) Channel shows which input (source) is assigned.
4. DESTINATION SELECT BUTTONS
Separate outputs 1 thru 8 select buttons are provided for each destination assignment.
Routing can be Source to Destination or one source to multiple destinations.
Example: Press Destination 1,3,5 then press Source 2 will route Input 2 to Output 1,3,5 respectfully.
5. EDID MODE SELECT BUTTONS
Used to select EDID mode using buttons #1 thru #2
6. IR SENSOR
The IR sensor receives IR commands from the supplied remote controller or a third party IR emitter.
7. SOURCE SELECT BUTTONS
Separate inputs 1 thru 8 select buttons are provided each source selection.
3

FRONT PANEL
FRONT PANEL
8. FUNCTION KEY - ALL
Disables (mute) video on all destinations OR Selects the same source to all destinations.
Option 1
- Press ALL followed by OFF button. The display will show “ 0 “ indicating all destinations have no video selected.
Option 2
- Press ALL followed by Source 1 thru 8. The display will show the Source selected.
- Press ENTER The pre-set source selection will be assigned all destinations.
9. FUNCTION KEY - OFF
Disables (mute) video to selected channels. Either destinations.
- Press OFF button followed by any Destination channel.
- Press thru 8 output destination. The display will show “ 0 “ for the selected channel indicating no video selected.
10. FUNCTION KEY - RECALL
The system will show previously stored presets, up to a total of 16. Presets are stored in local memory using Source keys 1 thru 8 or
Destination keys 1 thru 8 as the memory preset location.
- Press RECALL button.
- Press 1 thru 8 on either Source or Destination row.
- Press ENTER The pre-set configuration will execute.
Operation completes.
Note: Operation will abort if no keys are dressed within 5 seconds.
11. FUNCTION KEY - ENTER
Press ENTER to confirm entries.
4

FRONT PANEL
FRONT PANEL
12. FUNCTION KEY - MEMORY
The system will show store presets, up to a total of 16. Presets are stored in local memory using Source keys 1 thru 8 or Destination keys
1 thru 8 as the memory preset location.
- Configure desired matrices .
- Press MEMORY button.
- Press 1 thru 8 on either Source or Destination row.
- Press ENTER to ready memory location.
- Or press MEMORY again to cancel operation.
Operation completes.
Note: Operation will abort if no keys are dressed within 5 seconds.
13. FUNCTION KEY - LOCK
- Press and hold LOCK button for two seconds lockout the front panel.
- Press and hold LOCK button for two seconds to enable the front panel.
14. FUNCTION KEY - EDID
- Press EDID to select new EDID mode or select source row #1 or #2 for LINK source EDID again.
- Press the DESTINATION # to learn EDID The Destination EDID has been learned.
15. 19 INCH EAR MOUNT PAIR
Converts desktop to 19 inch rack mount. Bracket (part # 1U-440L) INCLUDED. Image shows rack mount bracket attached.
5

BACK PANEL
BACK PANEL
6
1. DC POWER INLET:
TheSwitcher isfitted with a DCpower pluginput connector. Ensure
that the used is of an approved type and is of sufficient current
carrying connector capacity with the correct voltage and connector
polarity. 12Volt DC power supply 5A Max (Center pin positive).
2. IR EXTENDER CONTROL:
Support one of IR Extender Extend distance maximum 300m
/ ~1000 ft. When you plug the external IR extender into the
switcher, the front panel IR receiver remains active.
3. RS-232 CONNECTION:
RS-232 control port to allow for interfacing to a PC, such as a
computer or touch panel control, to the switcher via this DB-9pin
female connector for serial RS-232 control.
4. PREVIEW OUTPUT-01 DVI-D:
Connect a signal link of HDMI direct digital video/audio
to this digital video/audio connector: Female DVI connector.
This connector supports DVI-D digital video/audio
and DVI-D digital video sources.
Preview port DVI-D signal as the same as Output 1
5. INPUTS- 1,2,3,4,5,6,7, & 8 DVI-D:
Connect a signal link of HDMI direct digital video/audio to this
Female DVI connector. This connector supports DVI-D digital
video/audio and DVI-D digital video sources.
DVI-D Digital Video, Connector with fix screw
Input 1 ~ Input 8
6. OUTPUTS- 1,2,3,4,5,6,7 & 8 DVI-D:
Connect a signal link of DVI-D direct digital video/audio to this
Female DVI connector. This connector supports DVI-D digital
video/audio and DVI digital video sources.
DVI-D Digital Video, Connector with fix screw
Output 1 ~ Output 8
Power Jack:
DC Jack - Inner OD Ø 2.1 mm (+)
Outside OD Ø 5.5mm (GND)
Power input -12VDC, 5A
IR Extender Jack: Female Jack - inner OD Ø 3.5mm
Remote port: DB-9pin Female connector
DVI-D digital video/audio connector:
DVI Female connector.
Note: With the proper adapters, the switcher can
be used with DVI-D digital video signals HDCP
compliant. DVI does not support audio.
DVI-D digital video/audio connector:
DVI Female connector.
Note: With the proper adapters, the switcher can
be used with DVI-D digital video signals HDCP
compliant. DVI does not support audio.
DVI-D digital video/audio connector:
DVI Female connector.
Note: With the proper adapters, the switcher can
be used with DVI-D digital video signals HDCP
compliant

7
REMOTE CONTROL
Before making any connections to the switcher, observe the following:
• Ensure the mains voltage supply matches the label on the supplied plug- Pack (+/- 10%).
• Ensure that the power switch is OFF.
• Ensure that all system grounds (earth) are connected to a common point.
• Avoid powering equipment within a system from multiple power sources that may be separated by large distances.
• Connect all audio video sources and destination equipment.
• Power up all source and destination audio-visual sources.
• For each destination output, select the appropriate input source by using the front panel input 1~8 select buttons, the supplied IR remote
control, or through the RS-232 serial communication port.
• Upon power up the switcher will return to its last used setting before Powered down.
REMOTE CONTROL
IR REMOTE CONTROL KEY : IR REMOTE : SW-8811
1. & 2. SWITCH POWER ON or OFF:
Controller with a separate power ON and OFF
3. DESTINATION : 1 thru 8 OUTPUT SELECTION:
Press the destination button to select the output display channel
4. SOURCE : 1 thru 8 INPUT SOURCE SELECTION:
Press input 1~8 sources with selection button
5. FUNCTION KEY:
ALL - function selection button
OFF - function selection button
EDID - function selection button
RECALL - function selection button
ENTER - function selection button
MEMORY - function selection button
LOCK - function selection button

8
REMOTE PROTOCOL COMMANDS
IR REMOTE CUSTOM AND DATA CODES (NEC STANDARD)
HOW TO SETUP IR CODES : CUSTOM CODE : 33CC
CUSTOM CODE : 33CC
POWER ON : 33CC A15E
POWER OFF : 33CC A25D
ALL : 33CC B04F
OFF : 33CC B14E
LOCK : 33CC B54A
EDID : 33CC B748
RECALL : 33CC B24D
ENTER : 33CC B34C
MEMORY : 33CC B44B
HOW TO GIVE IR COMMANDS:
PRESS DESTINATION - # then PRESS SOURCE - #
DESTINATION #1 : 33CC 01EF SOURCE #1 : 33CC 01FE
DESTINATION #2 : 33CC 20DF SOURCE #2 : 33CC 02FD
DESTINATION #3 : 33CC 30CF SOURCE #3 : 33CC 03FC
DESTINATION #4 : 33CC 40BF SOURCE #4 : 33CC 04FB
DESTINATION #5 : 33CC 50AF SOURCE #5 : 33CC 05FA
DESTINATION #6 : 33CC 609F SOURCE #6 : 33CC 06F9
DESTINATION #7 : 33CC 708F SOURCE #7 : 33CC 07F8
DESTINATION #8 : 33CC 807F SOURCE #8 : 33CC 08F7
For example;
Let Destination # 1 show the signal from Source #1~4
The IR Data Code list :
Destination # 1 & Source #1 33CC 01FE 33CC 01FE
Destination # 1 & Source #2 33CC 01FE 33CC 02FD
Destination # 1 & Source #3 33CC 01FE 33CC 03FC
Destination # 1 & Source #4 33CC 01FE 33CC 04FB
Destination # 1 & Source #5 33CC 01FE 33CC 05FA
Destination # 1 & Source #6 33CC 01FE 33CC 06F9
Destination # 1 & Source #7 33CC 01FE 33CC 07F8
Destination # 1 & Source #8 33CC 01FE 33CC 08F7