Access interfacing solutions Atr110 User manual

Access-IS

18 Suttons Business Park, Reading

Berkshire, RG6 1AZ, United Kingdom

Tel: +44 (0) 118 966 3333

Web: www.access-is.com

Email: [email protected]

Product names

mentioned herein are for

identification purposes

only and may be

trademarks and/or

registered trademarks of

their respective

companies.

ALL RIGHTS

RESERVED

Subject: ATR110 Manual

Revision: 1.0

Issue Date: 15/03/2016

ATR110

1D/2D Barcode Imager

(Barcode and NFC Version)

Product Manual

Warnings

This manual contains important information regarding the installation and operation of the ATR110 1D/2D

Barcode Imager. For safe and reliable operation of the imager, installers must ensure that they are familiar

with and fully understand all instructions contained herein.

Warranty

Access Ltd warrants that this product shall be free from defects in workmanship and materials for a period of

one year from the date of original purchase. If the product should fail to operate correctly in normal use during

the warranty period, Access will replace or repair it free of charge. No liability can be accepted for damage

due to misuse or circumstances outside Access’control. Access will not be responsible for any loss, damage

or injury arising directly or indirectly from the use of this product. Access’total liability under the terms of this

warranty shall in all circumstances be limited to the replacement value of this product.

Radio Frequency Energy

European EMC directive 89/336/EEC

This equipment has been tested and found to comply with the limits for a class A computing

device in accordance with the specifications in the European standard EN 55022. These

limits are designed to provide reasonable protection against harmful interference. This

equipment generates, uses and can radiate radio frequency energy and if not installed and

used in accordance with the instructions may cause harmful interference to radio or

television reception. However, there is no guarantee that harmful interference will not occur in a particular

installation. If this equipment does cause interference to radio or television reception, which can be

determined by turning the equipment on and off, the user is encouraged to correct the interference with one or

more of the following measures: (a) Reorient or relocate the receiving antenna. (b) Increase the separation

between the equipment and the receiver. (c) Connect the equipment to an outlet on a circuit different from that

to which the receiver is connected. (d) Consult the supplier or an experienced radio / TV technician for help.

FCC Compliance Statement (United States)

This equipment generates, uses and can radiate radio frequency energy and if not installed and used

properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio

communication. It has been tested and found to comply with the limits for a class A computing device in

accordance with the specifications in Subpart J of part 15 of FCC rules, which are designed to provide

reasonable protection against such interference when the equipment is operated in a commercial

environment. Operation of this equipment in a residential area may cause interference, in which case the user

at his own expense will be required to take whatever measures may be necessary to correct the interference.

Changes or modifications not expressly approved by the manufacturer could void the user’s authority to

operate the equipment.

Canadian Department of Communications RFI statement

This equipment does not exceed the class A limits for radio noise emissions from digital apparatus set out in

the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux

appareils numériques de la classe A prescrites dans le règlement sur le brouillage radioélectriques publié par

le ministère des Communications du Canada.

 
Page 3of 70 Copyright © Access-IS 2016 
 
Contents 
Overview....................................................................................................................5
Specifications.............................................................................................................6
1 Part numbers............................................................................................................... 7 
Installation..................................................................................................................8 
1 Unpack the ATR110.................................................................................................... 8 
2 Connection.................................................................................................................. 8 
3 Mounting ..................................................................................................................... 8 
4 Barcode interface options ......................................................................................... 11 
5 NFC interface............................................................................................................ 11 
6 Barcode module installation...................................................................................... 12 
7 NFC module installation............................................................................................ 12 
8 Test the device.......................................................................................................... 13 
9 Barcode configuration software................................................................................. 13 
10 Communicate with the NFC module ......................................................................... 13 
11 Troubleshooting ........................................................................................................ 14 
12 Maintenance.............................................................................................................. 14 
Barcode operating modes........................................................................................15
1 Mode summary ......................................................................................................... 15 
2 Dumb mode............................................................................................................... 16 
3 Host mode................................................................................................................. 17 
4 Interactive mode........................................................................................................ 19 
Barcode command reference...................................................................................21
1 Basic configuration.................................................................................................... 21 
2 Prefix and suffix solutions ......................................................................................... 22 
3 ATR110 illumination.................................................................................................. 23 
4 Indicator control......................................................................................................... 25 
5 Development commands .......................................................................................... 29 
6 Triggering.................................................................................................................. 31 
7 Counter ..................................................................................................................... 32 
NFC operation .........................................................................................................33
1 Summary of operation............................................................................................... 33 
2 MIFARE cards........................................................................................................... 35 
3 Contactless microprocessor smartcards................................................................... 35 
MIFARE media commands and responses..............................................................36 
1 MIFARE get media type............................................................................................ 36 
2 MIFARE load key...................................................................................................... 37 
3 MIFARE authenticate block (key A or key B)............................................................ 38 
4 MIFARE read block (key A or key B) ........................................................................ 38 
5 MIFARE write block (key A or key B)........................................................................ 40 
6 MIFARE create value block (key A or key B)............................................................ 41 
7 MIFARE increment value block (key A or key B)...................................................... 42 
8 MIFARE decrement value block (key A or key B)..................................................... 43 
9 MIFARE Ultralight read block.................................................................................... 44 
10 MIFARE Ultralight write block ................................................................................... 45 
11 MIFARE Ultralight-C authenticate - part 1................................................................. 45 
12 MIFARE Ultralight-C authenticate - part 2................................................................. 46 
13 MIFARE transceive direct ......................................................................................... 47 
14 MIFARE failure status codes..................................................................................... 48 
NFC module management interface commands......................................................50 
1 Get firmware version................................................................................................. 50 
2 Get bootloader version.............................................................................................. 51 
3 Switch to bootloader.................................................................................................. 51 

 
Page 4of 70 Copyright © Access-IS 2016 
8.4 Get serial number...................................................................................................... 52 
8.5 Set NFC timings........................................................................................................ 52 
8.6 Get NFC timings........................................................................................................ 53 
8.7 Enter sleep mode...................................................................................................... 54 
8.8 Exit sleep mode......................................................................................................... 55 
8.9 ATR110 LED control command ................................................................................ 55 
8.10 Get NFC kernel version............................................................................................. 57 
8.11 Get media serial number........................................................................................... 58 
A. NFC module serial number matching ......................................................................60 
B. HID reports - barcode only.......................................................................................61
B.1 Receive data............................................................................................................. 61 
B.2 Send commands....................................................................................................... 62 
B.3 Trigger controls......................................................................................................... 63 
C. NFC module example code and API functions ........................................................64 
C.1 Initialise smartcard sub-system................................................................................. 64 
C.2 Poll for card arrival.................................................................................................... 64 
C.3 Connect to the card................................................................................................... 64 
C.4 Get ATR of the card.................................................................................................. 65 
C.5 Communicate with card............................................................................................. 65 
C.6 Determine if ATR indicates MIFARE type................................................................. 65 
C.7 Disconnect the card .................................................................................................. 65 
D. ASCII character reference .......................................................................................66
E. Document history.....................................................................................................70
 

Figure 1. ATR110 1D/2D Barcode Imager with NFC

1. Overview

The ATR110 is a compact and fast barcode reader with Near Field Communication (NFC)

contactless capabilities. This ‘one-box’ solution helps process a wide range of electronic ticketing

across a variety of media.

The device reads all popular linear, PDF417 and 2D barcode symbologies, including QR and Aztec

codes, from smartphones, tablets and printed-paper documents. The ATR110’s advanced

recognition barcode imager is omnidirectional and has near-zero latency. It captures barcodes

within a fraction of a second of presentation in any orientation.

The device supports mobile ticketing and mobile wallet payment systems for NFC-enabled

smartphones and tablets, as well as reading contactless smart, credit and debit cards.

This responsive, intuitive-to-use device is simple to operate by untrained members of the public.

Additional user-friendly features include bright LED visual indicators and a programmable audio

buzzer to confirm successful data capture.

Its rugged, vibration and shock resistant construction, with no moving parts, enables the reader to

withstand years of frontline, public use.

Fast, intuitive imager with fixed focal

distance.

Reads barcodes on facedown

presentation of mobile device.

Reads 2D, PDF417 and linear barcode

symbologies.

Contactless NFC mobile ticketing and

payment.

USB (custom Human Interface Device

(HID), keyboard or Communications

Device Class (CDC) serial) interface

options.

Configurable LED (green, amber, red,

blue) and audible read confirmation.

Mounting options: desktop, console,

pole-mount and fixed-position

installation.

Protective rubber bumper to prevent damage to smartphones when placed against the unit’s

toughened glass.

Designed for a wide range of applications, including public transportation.

2. Specifications

Specification

Details

Dimensions (L x W x H)

120.6 mm x 96.0 mm x 81.2 mm

Weight

461 g (with cable)

Environmental

Operating temperature: -25ºC to 50ºC

Storage temperature: -30ºC to 70ºC

Humidity: 95% non-condensing

Designed to meet IP54

Body

Dark grey ABS with blue rubber smartphone bumper

Glass

3 mm thermally toughened low-iron Conturan IK07 (3 times 2J

impact), anti-reflective coating

Buzzer

Loud (75 dBa at 1 m); volume controllable (configuration setting -

can be adjusted by customer)

Indicator LEDs

Four colours (green/amber/red/blue) (configuration setting - can

be adjusted by customer)

Power requirements

5 V DC

Requires USB power injector cable or independent power supply

Electrical interface

5 V USB (only)

Barcode reading

Reads barcodes from mobile phones, tablets and paper

Linear: EAN/UPC, Code 2 of 5, Interleaved 2 of 5, IATA 2 of 5,

Code 39, Code 128

2D: IATA resolution 792, PDF417, Aztec, DataMatrix and QR

codes

NFC

EMV: Designed to Level 1

Supported media: ISO14443 type A and B cards (Java cards);

max baud 424K (extendable to 848K)

MIFARE UL, Classic 1K, Classic 4K, UL-C, MIFARE Plus; max

baud 106K

MTBF

85,000 hours

Approvals

CE EMC Class B

EN 55022

EN 55024

CE Low Voltage Directive

EN 60950-1

IEC 60825-1 LED Safety Class 1

CE R&TTE Directive

ETSI EN 301 489

ETSI EN 302 291

FCC 47CFR Part 15 Subpart B Class A

FCC 47CFR Part 15 Subpart C

2.1 Part numbers

Product

Part Number

Barcode and NFC-enabled, USB-connected ATR110

AKEGEOTA911

USB power injector cable

5KBD133402

Pole mount - 1.25 inches (31.75 mm) pole diameter

AKEGEOXB081

Pole mount - 1.5 inches (38.1 mm) pole diameter

AKEGEOXB091

An external power supply is available, if required.

Please contact the Access-IS sales team: [email protected].

3. Installation

3.1 Unpack the ATR110

Unpack the ATR110 and ensure that you have the following items:

Advisory notice card.

ATR110 device with attached USB cable.

USB power injector cable or power supply (IEC cable not supplied).

Report any missing items or damage immediately to your Sales Representative.

3.2 Connection

Connect the ATR110 directly to a USB port on the host.

Note: The cable is sealed into the unit to prevent entry of water, moisture and dust. Standard

supplied cable length is 1.8 m. Other options are available for pole mounting.

3.2.1 Connection to a USB port

Figure 2. Connection to a USB port

3.3 Mounting

The ATR110 is simple to install. Mounting options include desktop, console, kiosk or pole-mount.

Refer to Figure 3 for the dimensions of the unit. Figure 4 shows the mounting points.

For optimum performance, do not position the ATR110 in direct sunlight.

NFC INSTALLATION WARNING

To optimise the performance, DO NOT install the ATR110 so that its NFC antenna is within 40 mm

of a large metal or electrically conductive component or structure.

Failure to observe this instruction may lead to the product’s NFC performance deteriorating or even

failing completely.

To a USB port on the host PC

USB cable connected to ATR110 device

USB power injector cable to a powered USB

port on host PC (or connection to an external

power supply)

Figure 3. ATR110 dimensions (rounded to the nearest millimetre)

3.3.1 Mounting points

Figure 4. ATR110 mounting points

Use four M3 screws (not provided) to mount the unit. Maximum insertion depth is 4 mm; minimum

recommended insertion depth is 2 mm.

Figure 5. Pole-mount cable connection

3.3.2 Pole mounting

An optional pole-mount kit allows you to mount the device on a 1.25 inch or 1.5 inch diameter pole.

If the mounting bracket is pre-fitted to the unit,

attach the unit to the pole as follows:

1. Remove the two M3 screws holding the plastic

back cover in place on the ATR110.

2. Unscrew the four M4 screws holding the two

metal ‘U’ brackets together.

3. Wrap the drilling template around the pole and

drill the holes into the pole. Drill the smaller

holes (6 mm) all the way through the pole; drill

the larger hole (24 mm) on the front face of the

pole only.

4. Feed the cable through the larger hole in the

pole and screw the main cable to the cable

attached to the device.

5. Make the appropriate cable connections to the

host.

6. Position the ATR110 on the pole ensuring that

the locating studs on the metal ‘U’ brackets

engage in the two smaller holes in the pole.

Position the other metal ‘U’ bracket against the

back of the pole and screw the metal brackets

together using the four M4 screws removed

earlier.

7. Replace the plastic cover and screw into place

using the two M3 screws.

To attach the mounting kit to the ATR110

Follow these steps to attach the mounting kit to the

ATR110, if it is not pre-fitted to the device.

1. Remove the two M3 screws holding the plastic

back cover in place on the metal back plate.

2. Unscrew the four M4 screws holding the two

metal ‘U’ brackets together.

3. Unscrew the four screws holding the two plastic ‘U’-shaped mouldings to the top and bottom of

the mounting bracket.

4. Screw the mounting bracket to the back of the ATR110 using four M3 screws.

5. Replace the plastic ‘U’-shaped mouldings and screw into place.

6. Attach the unit to the pole following steps 3–7 above.

Figure 6. Mounting the ATR110 on a pole (View A)

Note: Mount the unit in either orientation.

Figure 7. Mounting the ATR110 on a pole (View B)

Table of contents

Other Access Interfacing Solutions Barcode Reader manuals

Access Interfacing Solutions

Access Interfacing Solutions BGR700 User manual

Access Interfacing Solutions

Access Interfacing Solutions LSR110 User manual

Access Interfacing Solutions ATR110 User manual

Popular Barcode Reader manuals by other brands