Cognex DataMan 260 Series User manual

DataMan®260 Series
Quick Reference Guide
04/24/2017
Version:5.7.0.218

Precautions
Observe these precautions when installing the Cognex product, to reduce the risk of
injury or equipment damage:
lThis device requires the use of an LPS or NEC class 2 power supply (non-
PoE device) or the use of a PoE Class 1 (PoE device).
lDo not connect or disconnect this device from the I/O module or 15-pin USB
adapter cable while the I/O module or adapter cable is connected to a PC .
lTo reduce the risk of damage or malfunction due to over-voltage, line noise,
electrostatic discharge (ESD), power surges, or other irregularities in the
power supply, route all cables and wires away from high-voltage power
sources.
lChanges or modifications not expressly approved by the party responsible
for regulatory compliance could void the user’s authority to operate the
equipment.
lCable shielding can be degraded or cables can be damaged or wear out
more quickly if a service loop or bend radius is tighter than 10X the cable
diameter. The bend radius must begin at least six inches from the
connector.
lThis device should be used in accordance with the instructions in this
manual.
lAll specifications are for reference purpose only and may be changed
without notice.
2

Product Overview
1 Illumination LEDs
2 LED aimers
3-4* Mounting holes (M3 x 3.5mm)
5Trigger button
6Power indicator
7 Train status/Trigger status indicator
8 Good/bad read indicator
9 Network status indicator
10 Error indicator
11 Tune button
12 Power, I/O and RS-232 connector
13 Ethernet connector
Note: *Use only one set of mounting holes (either 3 OR 4) for mounting.
Note: The five status LEDs together also function as a peak meter using an orange light.
3

DataMan 260 Accessories
LENS OPTIONS, COVERS, ILLUMINATIONS AND FILTERS
6.2 mm lens kit DM150-LENS-62
IR 6.2 mm lens kit, 3 -position with IR LED DMA-KIT-IR-62
IR16 mm lens kit DMA-KIT-IR-16
16 mm lens with extended optics mount (requires the
use of an extended front cover and high-powered red
LED)
DM260-LENS-16
Liquid Lens Module (LLM) to be used with 6.2 mm lens
or 16 mm lens
DMA-LLM-150-260
ImageMax kit DM260-KIT-16LL
Clear lens cover* DM150-CVR-CLR
Clear lens cover,ESD safe* DM150-CVR-ESD
Polarized front cover* DM260-LENS-62CVR-
F***
Extended lens cover, un-polarized**
Extended lens cover, half-polarized **
Extended lens cover, fully polarized**
DM260-LENS-16CVR***
DM260-LENS-16CVR-
P***
DM260-LENS-16CVR-
F***
C-mount adaptor, IP40 DM260-CMNT-00
C-mount adaptor, IP65 DM260-CMNT-CVR
4

Blue bandpass filter DM150-BP470
Red bandpass filter DM150-BP635
Red LED illumination*
White LED illumination*
Blue LED illumination*
DM150-LED-RED
DM150-LED-WHT
DM150-LED-BLU
High Powered red LED illumination** DM260-LED-RED-HP
Note: *Use with a 6.2 mm lens only!
**Use with a 16 mm lens only!
***ESD safe
CABLES ANDOTHER
Connection cable 24V, I/O, RS-232 CCBL-05-01
CCB-M12x12Fy-xx (y=S:
straight / y=A: angled *, xx
specifies length)
Connection cable RS-232 CCB-M12xDB9Y-05
Adapter cable, M12x12 to M8x4/M8x5, 0.5 m DM260-ADAP-M12M8
X-Coded to RJ45 Ethernet Cable CCB-84901-2001-xx,
where xx can be 02, 05, 10,
15 or 30, indicating length
in meters
Adapter cable, ETH, M12, X-CODED/A-CODED, 0.5 m CCB-M12x8MS-XCAC
Universal Mounting Bracket DM100-UBRK-000
Pivot Mounting Bracket DM100-PIVOTM-00
DataMan 362 to DataMan 262 adapter kit DM-ADAP-PLT
5

Dimensional Drawings
6

Field of View and Reading Distances
7

8

Connecting the Reader
9

Installation
Installation procedures and specifications are presented in detail in the DataMan®
260 Reference Manual, which is installed with the DataMan Setup Tool. From the
Windows Start menu, select the following to access the manual: All Programs >
Cognex > DataMan Software vx.x.x > Documentation.
Note:
lCables are sold separately.
lIf any of the standard components appear to be missing or damaged,
immediately contact your Cognex Authorized Service Provider (ASP)
or Cognex Technical Support.
CAUTION:All cable connectors are “keyed” to fit the connectors on the
reader; do not force the connections or damage may occur.
Mounting
Mounting the DataMan 260 at a slight angle (15°) can reduce reflections and
improve reader performance.
Use the set of mounting holes on the rear part to mount the DataMan reader.
10