Honeywell Xenon 1900H User manual

Enhanced Xenon™ 1900H
Corded Area-Imaging Scanner for Healthcare
Quick Start Guide
Rev A
8/15
Aller à www.honeywellaidc.com pour le français.
Vai a www.honeywellaidc.com per l'italiano.
Gehe zu www.honeywellaidc.com für Deutsch.
Ir a www.honeywellaidc.com para español.
Idźna stronę: www.honeywellaidc.com po quick start w języku polskim.
Перейти на русскоязычный сайт www.honeywellaidc.com.
Pro češtinu jdi na www.honeywellaidc.com.
Pre slovenčinu choďna www.honeywellaidc.com
Para Português, acesse www.honeywellaidc.com.br.
日本語 : www.honeywellaidc.com をご覧ください。
如要到中国 www.honeywellaidc.com（简体）。
查看繁体版请登陆 www.honeywellaidc.com
한글 www.honeywellaidc.com 로이동합니다 .
ʲʡʤʱʸʢʬʡʺʩʸˬʺʡʥʺʫʡʨʰʸʨʰʩʠʤʸʺʠʬʸʥʡʲwww.honeywellaidc.com.
Çäè´á Åàˆ moc.cdiallewyenoh.www ààú¬ ÇàõÑéí¬

Note: Refer to your user’s guide for information about cleaning your
device.
For localized language versions of this document, go to
www.honeywellaidc.com.
Getting Started
Turn off computer’s power before connecting the scanner, then
power up the computer once the scanner is fully connected.
Power Supply Assembly (if included)
Note: The power supply must be ordered separately, if needed.

Connecting the Scanner
USB:
Keyboard Wedge:

RS232 Serial Port:
Reading Techniques
The view finder projects an aiming
beam that should be centered over
the bar code, but it can be
positioned in any direction for a
good read.
Hold the scanner over the bar code,
pull the trigger, and center the
aiming beam on the bar code.
The aiming beam is smaller when
the scanner is closer to the code and larger when it is farther from the
code. Hold the scanner close to smaller bar codes, and farther away
from large bar codes to get a proper read.
If the bar code is highly reflective (e.g., laminated), you may need to
tilt the scanner at an angle so the bar code can be scanned.

Standard Product Defaults
The following bar code resets all standard product default settings.
Standard Product Defaults
USB Serial
Scan the following code to program the scanner to emulate a regular
RS232-based COM Port. If you are using a Microsoft® Windows®
PC, you will need to download a driver from the Honeywell website
(www.honeywellaidc.com). The driver will use the next available
COM Port number. Apple® Macintosh computers recognize the
scanner as a USB CDC class device and automatically use a class
driver.
USB Serial
Note: No extra configuration (e.g., baud rate) is necessary.
USB PC Keyboard
Scan the following code to program the scanner for a USB PC
Keyboard.
USB PC Keyboard

Epic
Scan the following bar code to configure your device to communicate
with an Epic software application.
EMR Application
Meditech®
Scan the following bar code to configure your device to communicate
with a Meditech software application.
Meditech Application

Quiet Operations
The following codes configure the scanner for quiet modes that do
not disturb resting patients.
Silent Mode with Flashing LED
Scan the following bar code to completely silence the scanner. When
a bar code is scanned, the LED and aimer flash 5 times. Green
indicates a good scan, red indicates a bad scan.
Silent Mode with Flashing LED
Silent Mode with Long LED
Scan the following bar code to completely silence the scanner. When
a bar code is scanned, the LED and aimer remain solidly lit for 1
second. Green indicates a good scan, red indicates a bad scan.
Silent Mode with Long LED
Very Low Beeper (Nighttime Mode)
The following bar code programs the scanner for a very low beep.
When a bar code is scanned, the scanner emits a very soft beep.
Nighttime Mode

Low Beeper (Daytime Mode)
The following bar code programs the scanner for a low volume.
When a bar code is scanned, the scanner emits a low beep.
Daytime Mode
Trigger
The following bar codes will allow you to use the scanner in Manual
Trigger - Normal Mode (need to press the trigger to read) or
Presentation mode (the scanner is activated when it “sees” a bar
code).
Manual Trigger - Normal
(Default)
Presentation Mode
Streaming Presentation™
When in Streaming Presentation mode, the scanner leaves the scan
illumination on all the time and continuously searches for bar codes.
Streaming Presentation Mode

Suffix
If you want a carriage return after the bar code, scan the Add CR
Suffix bar code. To add a tab after the bar code, scan the Add Tab
Suffix bar code. Otherwise, scan the Remove Suffix bar code to
remove the suffixes.
Add CR Suffix
Remove Suffix
Add Tab Suffix
Add Code ID Prefix to all Symbologies
Scan the following bar code if you wish to add a Code ID prefix to all
symbologies at once.
Add Code ID Prefix To All Symbologies
(Temporary)
Note: For a complete list of Code IDs, see the User’s Guide for your
product at our website, www.honeywellaidc.com.

Keyboard Country
Scan the appropriate country code below to program the keyboard
layout for your country or language. By default, national character
replacements are used for the following characters: #$@[\]^‘{|}~
Refer to the ISO 646 Character Replacements chart in your User’s
Guide to view the character replacements for each country.
USA (Default)
Belgium
Denmark
Finland
France
Germany/Austria
Great Britain