Access IS VAL100 User manual

Subject: VAL100 Installation
Manual
Version: 3.0
Date: 10/12/2020
Product names mentioned
herein are for identification
purposes only and may be
trademarks and/or registered
trademarks of their respective
companies.
© Copyright 2020
ALL RIGHTS RESERVED
Access-IS
18 Suttons Business Park, Reading
Berkshire, RG6 1AZ, United Kingdom
Tel: [phone]
Web: www.access-is.com
Email: [e-mail]
VAL100
Barcode/NFC/RFID Ticket
Validator
Installation Manual

Page 2of 17 Copyright © Access-IS 2020
Warnings
This manual contains important information regarding the installation and operation of the VAL100. For safe
and reliable operation of the imager, installers must ensure that they are familiar with, and fully understand, all
instructions contained herein.
Warranty
Access Ltd warrants that this product shall be free from defects in workmanship and materials for a period of
one year from the date of original purchase. If the product should fail to operate correctly in normal use during
the warranty period, Access will replace or repair it free of charge. No liability can be accepted for damage
due to misuse or circumstances outside Access' control. Access will not be responsible for any loss, damage
or injury arising directly or indirectly from the use of this product. Access' total liability under the terms of this
warranty shall in all circumstances be limited to the replacement value of this product.
(Non- RFID version)
This product meets the requirements of the following directives and carries the CE marking
accordingly; 2014/35/EU Low Voltage Directive, 2014/30/EU EMC Directive, 2015/863/EU RoHS 3
Directive.
(RFID version)
This product meets the requirements of the following directives and carries the CE marking
accordingly; 2014/53/EU Radio Equipment Directive, 2015/863/EU RoHS 3 Directive.
Compliance Statement (United States)
Supplier’s Declaration of Conformity
47 CFR §2.1077 Compliance Information
Unique Identifier: VAL100 On-board Validator Barcode/NFC & RFID/cEMV Payments
Responsible Party –US contact information:
MONICA GLOZER
ACCESS-IS
ROEDL LANGFORD DE KOCK, LLP
110 SOUTH TOWER
225 PEACHTREE ST. NE
ATLANTA
GA 30303
Email:[e-mail]
FCC Compliance Statement (Products subject to Part 15):
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
The RFID version contains FCC approved Access-IS Module FCC ID: ZERCPM01
Canadian Department of Communications RFI statement
This equipment does not exceed the class A limits for radio noise emissions from digital apparatus set out in
the radio interference regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numériques de la classe A prescrites dans le règlement sur le brouillage radioélectriques publié par
le ministère des Communications du Canada.
The RFID version contains approved module IC: 9653A-CPM01

Page 3of 17 Copyright © Access-IS 2020
Contents
1. Overview.............................................................................................................................4
2. Installation...........................................................................................................................5
2.1 Unpack the VAL100..................................................................................................5
2.2 Tool list.....................................................................................................................6
2.3 Cable requirements ..................................................................................................6
2.4 Pole mount procedure ..............................................................................................6
2.5 SAM card installation................................................................................................8
2.6 Test the device.......................................................................................................10
2.7 Troubleshooting......................................................................................................10
2.8 Maintenance...........................................................................................................10
A. Wiring guide ......................................................................................................................11
B. Installation drawings..........................................................................................................13
C. Specifications....................................................................................................................15
D. Main model numbers.........................................................................................................16
D.1 Validators ...............................................................................................................16
D.2 Mounting kits ..........................................................................................................16
E. Document history ..............................................................................................................17

Page 4of 17 Copyright © Access-IS 2020
1. Overview
The VAL100 is a ticket validator designed for use on-board buses, trams, trains and boats.
Designed for use in a variety of public transportation automatic fare collection systems, the VAL100
combines a multimedia ticket reader with an open architecture Linux computer to create a mobile
ticket validation solution when combined with third-party software.
The validator combines barcode and Near Field Communication (NFC) /Radio Frequency
Identification (RFID) reading functionality to provide a single point of presentation for tickets and
travel passes –whether presented on a card, mobile phone or tablet.
The VAL100 can be connected over the internet via wired Ethernet, Wi-Fi or cellular modem.
•Robust design for long-term front-line use.
•Single point of presentation barcode/NFC/RFID
reader.
•Four Secure Access Module (SAM) card slots
(optional).
•Large, clear 480 x 272 TFT LCD colour screen,
with illumination that is adjustable in software.
•Four coloured LEDs and a programmable
speaker to confirm ticket reads.
•Unique, optimised focal distance improves card
and mobile device reading performance.
•Linux computer with a variety of peripheral
hardware allowing for integration of ticket
validation software.
•Comes with a pole mount kit for ease of
installation. This has a quick release mechanism
allowing rapid exchange of the VAL100 for ease
of maintenance.
•Can be connected to 12–24 V feed from the
vehicle's ignition system. Operational voltage
range 10.5 to 33 V.
•Ambient light sensor adjusting the display
brightness to the ambient light conditions.
Figure 1: VAL100 on-board validator

Page 5of 17 Copyright © Access-IS 2020
2. Installation
Mount the VAL100 on a 1.25 inch or 1.4 inch diameter pole.
The validator requires a 12–24 V feed from the vehicle's ignition. Operational voltage range 10.5 to
33 V.
Warning: Ensure that the vehicle ignition is switched off during installation and when you connect
the VAL100.
2.1 Unpack the VAL100
Unpack the VAL100 and ensure that you have the following items:
Table 1: VAL100 parts list
Quantity
Description
1
VAL100
1
Mounting bracket with security lock
2
Pole clamps
1
Connector bracket
1
Pole cover
2
Security lock keys
1
14-way connector*
4
Crimps 24-18 AWG
20
Crimps 28-22 AWG
1
Ferrite
4
M3 x 6 Torx countersunk screws
6
M4 x 10 screws with captive washer
1
Adhesive drilling template
* Only provided for non-4G models.
Additional items for the 4G version of the product only:
Table 2: Items specific to the 4G version of the VAL100
Quantity
Description
1
USB dongle cable*
2
M3X8 P/HD captive washer
2
M4 x 8 screws with captive washer
3
M4 nylon insert nut
1
USB dongle bracket with thermal transfer pad
1
USB dongle clamp with foam pad
* Comprises a USB adapter cable pre-wired into a 14-way connector block.
Report any missing items or damage immediately to your Sales Representative.

Page 6of 17 Copyright © Access-IS 2020
2.2 Tool list
To install the VAL100, you will require the following tools:
•Molex 63819-1000 22-28 AWG Crimp Tool
•Molex 63819-0900 18-24 AWG Crimp Tool
•Molex 11-03-0044 Crimp Extraction Tool
•PZ2 Driver
•T10 Driver
•6 mm Drill Bit
•25 mm Hole Saw
•Deburring Tool
2.3 Cable requirements
The cables required to install the VAL100 are as follows:
Power cable
•2-core 18 AWG, STRANDED
Ethernet cable (optional)
•Cat 5e/Cat 6 USTP - 24 or 26 AWG, STRANDED
USB cable (optional)
•USB 2.0 compatible cable - no longer than 4.5 metres
2.4 Pole mount procedure
Use the supplied pole mount kit to install the VAL100 on a pole in the vehicle. You can mount the
VAL100 on a 1.25 inch or 1.4 inch diameter pole.
Before starting this procedure, ensure that you have the correct mounting kit for the pole size that
you are using and the required tools and cables.
Refer to the Installation drawings (on page 13) if you need further help with installation procedure.
Warning: Ensure that the vehicle ignition is switched off during installation and when you attach the
VAL100 to the mounting bracket. Access-IS recommend that a 3 A fuse is connected in line with the
12/24 V supply cable.
1. Wrap the drilling template around the pole.
Use the horizontal lines at the top and bottom of the template to ensure that the template is
aligned correctly.
2. Drill holes into the pole, as marked on the template. Three holes are required on the front face,
two holes on the back.
A 6 mm drill and 25 mm hole saw are recommended.
3. Deburr all holes inside and outside of the pole with a deburring tool.
4. Position the mounting bracket on the pole ensuring that the locating studs engage in the two
smaller holes in the front face of the pole.

Page 7of 17 Copyright © Access-IS 2020
4G only: If you are using the 4G dongle, pass the provided USB dongle cable through the cable
aperture in the mounting bracket before carrying out this step. Make sure the USB cable passes
the pole on the right side (when looking at it from the front of the validator).
5. Position each pole clamp against the back of the pole and attach to the mounting bracket using
two M4 screws.
6. Thread the cables through the pole.
The cables must exit the pole through the 25 mm hole and provide sufficient slack for crimping.
7. Strip and crimp the ends of the cables.
8. Insert the crimps into the white connector block.
4G only: The dongle cable comprises a 14-way white connector block, with a USB adapter
cable pre-wired into it, leaving 10 available pins to use for Ethernet and power. There is no
space for wiring another USB cable for other uses.
Refer to the wiring guide (on page 11) and note the orientation of the white connector block.
9. 4G only: Position the USB dongle bracket over the three threaded studs on the mounting
bracket. Secure with an M4 nylon insert nut.
10. 4G only: Secure the socket of the USB dongle cable to the USB dongle bracket using two M4 x
8 screws with captive washer.
11. 4G only: Unpack the 4G USB dongle and load a Standard sized SIM card (also known as a Mini
SIM). Refer to the dongle’s quick start documentation for correct SIM loading instructions.
12. 4G only: Insert the 4G USB dongle into the socket of the USB dongle cable. Ensure that the
dongle is inserted as far down as it will go. Fit the USB dongle clamp over the 4G USB dongle
lining up the holes with those in the USB dongle bracket. Secure the clamp with two M4 x 8
screws, tightening them fully.
13. 4G only: Secure the ferrite of the USB dongle cable to its fixing position on the USB dongle
bracket using a ‘zip tie’.
14. Add sleeving or tape to the external sheath and clip the ferrite to the power cable, less than 100
mm from the connector.
It is recommended that you to tie the cables together with a ‘zip tie’.
15. Push the white connector block into the connector bracket and secure the assembly to the
mounting bracket using two M4 screws.
The following drawing shows the orientation of the connector.
Figure 2: Connector block orientation
16. Ensure the cables are positioned centrally, to avoid contact with any sharp edges, and carefully
feed back any slack wire.
17. Fit the rear plastic cover and attach to the mounting bracket using four M3 screws (use a T10
Torx tool to secure the screws).
You can now fit the blanking plate or validator to the mounting bracket.
18. Locate the fixings on the back of the blanking plate or validator in the holes on the blanking plate
and slide down until fully engaged.
19. To secure the equipment, push in the security lock until it clicks.

Page 8of 17 Copyright © Access-IS 2020
2.5 SAM card installation
SAM cards are usually installed at the factory. For on-site installation, follow these steps.
1. Remove the 11 screws securing the rear cover housing and prise the front and rear cover
housing apart.
2. Remove the screw securing the cover plate.
3. Remove the SAM cover plate.

Page 9of 17 Copyright © Access-IS 2020
4. Slide the metal lock bar to release the SAM socket cover.
5. Pivot the SAM socket cover up and insert the card (note the orientation of the chamfered corner
on the card).
6. Pivot the cover closed and slide the lock bar to the lock position.
7. Replace the SAM cover plate and replace the screw.
8. Re-fit the main rear cover housing and secure with 11 screws.
9. Test the device.

Page 10 of 17 Copyright © Access-IS 2020
2.6 Test the device
Once you have connected the VAL100 to the mounting plate, you can test the validator. Refer to the
User Guide provided by the System Integrator for instructions on how to test the validator. If the
device fails to respond when connected, refer to the Troubleshooting section in this document.
2.7 Troubleshooting
If the VAL100 does not appear to be working, refer to the following table to help identify and resolve
the problem. For further assistance, contact Customer Support ([e-mail]).
Alternatively, use the Contact Customer Support page on the Access-IS website.
Note: Do not attempt to disassemble the VAL100 if it does not operate correctly. Any attempt to do
so may be dangerous and will invalidate the warranty.
Table 3: Troubleshoot the VAL100
Problem
Solution
VAL100 not transmitting data to host
Check that all cable connections between the VAL100
and host are secure and are correctly wired.
Ensure that the unit has power.
VAL100 cannot scan ticketing media
Ensure that the unit is configured to read the media that
you are scanning.
If scanning a document, ensure that the print quality is
good.
If scanning a barcode on a mobile phone, ensure that
you set the screen backlight on the phone to its
brightest setting.
2.8 Maintenance
2.8.1 Cleaning
Clean the glass with a lint-free cloth. If the glass is dirty, wipe the glass with a lint-free cloth
moistened with isopropyl alcohol or use an alcohol wipe. Do not use abrasive cleaners.
2.8.2 Storage
Store the unit in its original box, at a temperature of -30°C to 70°C.

Page 11 of 17 Copyright © Access-IS 2020
A. Wiring guide
Figure 3: Wiring guide and connector orientation

Page 12 of 17 Copyright © Access-IS 2020
Table 4: Molex, Ethernet, USB and Power connections
Molex
Ethernet
USB*
Power
1
7 - TxP3 - WHITE/BROWN
2
8 - TxN3 - BROWN
3
USB 5 V
4
USB+
5
USB-
6
USB GND
7
BLACK - VEHICLE GROUND
8
5 - TRP2 - WHITE/BLUE
9
4 - TRN2 - BLUE
10
1 - TxP1 - WHITE/ORANGE
11
2 - TxN1 - ORANGE
12
3 - TxP0 - WHITE/GREEN
13
6 - TxN0 - GREEN
14
RED - VEHICLE 12/24 V
* Pre-wired with a USB adapter cable in the 4G version of the product.

Page 13 of 17 Copyright © Access-IS 2020
B. Installation drawings
Figure 4: Attach the mounting bracket to the pole
Figure 5: Mounting bracket attached to the pole
4G only
Figure 6: Fit the USB dongle bracket onto the
mounting bracket and secure
4G only
Figure 7: USB dongle bracket showing all fixings
4G only
Figure 8: Secure the USB socket on the USB dongle
cable to the USB dongle bracket
4G only
Figure 9: Insert the 4G dongle and secure with the
4G dongle clamp

Page 14 of 17 Copyright © Access-IS 2020
Figure 10: Connect the wiring block
Figure 11: Attach the back cover
Figure 12: Positions of the keyholes for attaching the
validator
Figure 13: Attach the validator

Page 15 of 17 Copyright © Access-IS 2020
C. Specifications
Specification
Details
Dimensions - Main unit
145.5 mm x 265 mm x 188 mm (W x H x D)
Weight
Validator: 1.7 kg, Mounting kit: 0.95 kg
Environmental
Operating temperature: -20ºC to 50ºC
Storage temperature: -30ºC to 70ºC
Humidity: 0–95% RH, non-condensing
Body
PC/ABS
Display
480 x 272, widescreen, sunlight-readable
Glass
4 mm Toughened White Soda Lime; BS EN60068-2-75 & IEC
62262:2002, rated to 3.5J impact
Power requirements
10.5–33 volts –automotive grade power supply
Communications and host
Communication: 3G*/4G*/GPRS* (*Optional)
Connection: USB, Ethernet, GPS; Wi-Fi; Bluetooth 4/Bluetooth Low
Energy; RS232
Host: Dual core 1GHz 1GB RAM, 32GB memory with 128GB optional
upgrade, Linux OS, full API and device access for developers
LED indicators: 4 x RGB LEDs
Sound: Speaker with digital control for audio playback
Reader - Barcodes
Reads the following barcode symbologies:
Linear: EAN, UPC, Code 2 of 5, Interleaved 2 of 5, IATA 2 of 5, Code
39, Code 128
2D: IATA resolution 792, PDF417, Aztec, DataMatrix and QR codes
Performance: Will read 2D barcodes from paper, mobile phones and
tablets
Reader - NFC/RFID
Reads NFC-enabled mobile phones and contactless smart and
banking cards
EMV Level 1 and Level 2. PCI-SRED 5.1 compliant, 4 SAM slots
NFC tags supported: Mifare 1K/4K Classic tags, Mifare UL, Mifare
Plus, ISO14443-4 Type A, ISO14443-4 Type B, HID iClass tags (only
CSN read supported), NXP iCode tags, Apple pay/VAS
Payment Schemes supported: VISA, MasterCard, Discover, American
Express
MTBF
50,000 hours
Approvals
EMC
•FCC 47CFR Part 15 Subpart B Class A
•55032:2015 Class A
•EN 55024
Radio
•FCC 47CFR Part 15 Subpart C
•ETSI EN 302 291
Safety
•IEC 62368-1
•EC 62471 (LED Safety) Exempt Risk Group
Ingress
•IP54

Page 16 of 17 Copyright © Access-IS 2020
D. Main model numbers
D.1 Validators
Model
Barcode
RFID
NFC
cEMV
Wi-Fi
Bluetooth
BLE
USB
Serial
Ethernet
Flash
memory
VAL100-210-WE-D3
32GB
VAL100-210-WE-D1
128GB
VAL100-210-WS-D3
32GB
VAL100-210-WS-D1
128GB
VAL100-210-WB-D3
32GB
VAL100-210-WB-D1
128GB
VAL100-220-WE-D3
32GB
VAL100-220-WE-D1
128GB
VAL100-220-WS-D3
32GB
VAL100-220-WS-D1
128GB
VAL100-220-WB-D3
32GB
VAL100-220-WB-D1
128GB
D.2 Mounting kits
Model
Cellular modem prepared
Diameter (inches)
Diameter (mm)
VAL100-00-MA
1.25
31.75
VAL100-00-MC
1.4
35.5
VAL100-00-PK4G-125
1.25
31.75
VAL100-00-PK4G-140
1.4
35.5

Page 17 of 17 Copyright © Access-IS 2020
E. Document history
Version
Date
Description
1.0
15/09/2016
First issue.
1.1
06/10/2016
Changes to USB connections and wiring guide.
2.0
10/01/2017
Addition of 4G dongle installation steps.
3.0
10/12/2020
Changed compliance statements and overview text, removed
1.5 inch pole option, changed operational voltage range, added
SAM card installation, updated specifications and approvals,
revised main model number section.