AccuBANKER QuadScan D470 User manual

User Guide
QuadScan D470
4 Way Orientation Detector

Thank you for trusting AccuBANKER with your cash handling needs. In
order to optimize the performance of your equipment, we encourage you to
thoroughly read this user guide prior to use.
AccuBANKER and its logo are registered trademarks of Hilton Trading Corp. All Rights Reserved.

3
Table of Contents
BOX CONTENTS....................................................................................................... 4
1. SAFETY INSTRUCTIONS ................................................................................... 5
2 . EQUIPMENT OVERVIEW ................................................................................... 7
3. OPERATION .......................................................................................................... 9
4. SOLUTIONS TO OPERATIONAL PROBLEMS ............................................... 12
6. SPECIFICATIONS ................................................................................................ 17
5. SOFTWARE UPDATES ..................................................................................... 16
4.1 Preventive Measures ........................................................ 12
4.2 Maintenance ..................................................................... 13
3.1 Basic Operation ............................................................. 9
3.2 Suspicious Bill Warning ............................................... 10
3.3 Bill Positioning .............................................................. 11
4.3 Jamming .......................................................................... 14
INTRODUCTION ...................................................................................................... 4
4.5 IR Sensor Calibration ....................................................... 15
4.4 Cleaning of Magnetic Heads............................................. 14

4
Introduction
The D470 incorporates the most modern techniques for the evaluation and
detection of counterfeit bills. This detector assesses in detail the security features
that are present in each bill and determines if these are genuine or suspicious. The
equipment automatically alerts the user both visually and audibly when a
suspicious bill is identified.
Box Contents
1. D470
2. Power Adapter
3. User Guide
4. Warranty Booklet
1.
2.3.4.

1. Safety Instructions
!Warning
Do not use this product in areas where it may be exposed to water or
other
liquids.
Unplug this equipment from the wall outlet before cleaning. Do not use
liquid or aerosol cleaners. Use a damp cloth for cleaning.
Only use the cable provided with the unit. The use of other cables may
result in electric shock, fire or cause serious damage to the equipment.
Do not operate the equipment in areas with high temperature or high
humidity since it may prevent it from working correctly.
To reduce the risk of electric shock, do not disassemble this equipment.
Take it to qualified service personnel when service or repair work is
required. Opening or removing covers may expose you to dangerous
voltages or other risks. Incorrect reassembly can cause electric shock when
the equipment is subsequently used.
! Caution
When unplugging the power cord, do not pull by the cord, but rather grip
the plug to pull it out. Not following these instructions may result in
electric shock, fire or damage to the equipment.
Do not use the equipment if the power cord is damaged or if the plug
socket contact is loose. Not following these instructions may result in
electric shock, fire or other hazards.
Do not place heavy objects over the cord and do not bend it excessively
since it could get damaged. Not following these instructions may result in
electric shock, fire or other hazards.
Remove the power plug from the wall outlet if the unit will not be used for
a long period of time.
5

Safety Instructions
cont.
•Follow all warnings and instructions marked on the unit.
•This equipment is meant to be operated in an indoor environment with proper ventilation.
•Do not place near direct sunlight, heat sources or air conditioners.
•This equipment should only be operated with the power cord supplied and the type of power source
indicated in this user guide. If you are not sure of the type of power supply in your location, consult
your vendor or local power company.
•To avoid risk of fire or electric shock, never push objects into the equipment through the case slots or
openings since they may touch dangerous voltage points or shortcut parts. Do not disassemble unit.
•Never spill liquids of any kind on the equipment.
•Unplug this equipment from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
- When the power supply cord or plug is damaged or frayed*
- If liquid has been spilled into the unit or it has been exposed to rain or water*
- If the unit has been dropped or the case has been damaged*
- If the equipment shows a noticeable change in performance *Not covered under warranty
If the unit does not operate normally while following the
instructions, adjust only those controls covered by the operating
!
instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a
qualified technician to restore the product to normal operation.
6

7
2.Equipment Overview
1. LED Indicator Display
2. Feeding Channel
3. SD Card Port
4. Bill Exit Slot
123
8
6
5. USB Interface Port
6. Power Adapter Connector
7. On / Off Power Switch
8. Serial Port
5
47

Equipment Overview
cont.
8
12
910
11
9. Green Indicator (Indicates bill accepted)
10. Red Indicator (Indicates suspicious bill)
11. Grips for the AccuStand metal base
12. AccuStand metal base (Optional Accessory / Sold
separately)
13. Battery compartment (Battery Optional / Sold
separately)
13

9
1. Connect the power cable to the detector and then connect the adapter to the
power outlet. When turning on the detector, it will proceed with a self-check
routine that lasts 2 seconds. The display will light the green indicator ,
which means the equipment is ready to check the bills.
2. Insert the bill to be checked in any direction. When a bill is inserted
into the detector's feeding channel, an optical sensor located in this
compartment allows the detector to automatically begin the verification process.
The bill will be transported inside the unit and analyzed immediately.
will light up and sound a single warning
will light up and sound two warning
3. If the bill is genuine, the green indicator
beep.
4. If the bill is suspicious, the red indicator
beeps.
3.Operation
3.1 Basic Operation

Operation cont.
3.2 Suspicious Bill Warning
This equipment checks the Magnetic (MG), Infrared (IR) , Watermark (WM),
Ultraviolet (UV) and other characteristics of the bills analyzed. If any of these
security features do not pass the authentication of the bill, a red indicator will
display and two beep notifications sound. If a bill is detected as suspicious,
we recommend passing the bill at least three more times in different
positions. Bills can be rejected due to different reasons, such as:
-Bills are too crumpled
-Bills are very stained or dirty
-Ripped bills
-Wet bills
-Bills stuck with adhesive tape or stapled
10

11
Operation cont.
3.3 Bill Positioning
- This equipment has the ability to verify the authenticity of bills in any of four
positions.
- For correct verification, the bill must be introduced into the feeding channel
straight and aligned all the way to the left edge, as shown in Figure
"A" and "B". Avoid introducing the bill into the feeding channel separated
from the left side and/or at an angle as shown in Figure "C".
ABC

12
4.Solutions to Operational Problems
4.1 Preventive Measures
For optimal operation of the detector, take into account the following:
1. Avoid direct exposure to powerful sources of light as well as magnetic
interference (ex. microwave, cell phone or WiFi devices), which will
affect the sensors of the detector.
2. Keep the sensors clean.
3. Keep the equipment off when it is not being used for a long period of time.
4. Check the status of the bills and avoid processing:
- Bills with clips, adhesive tape or other glue
- Broken or badly damaged bills
-Bills affected by chemical agents of any kind

13
a) Cleaning of optical sensors
It is important to periodically clean the optical sensors to prevent particles of paper
or dust adhering to them.
b) Internal cleaning of the unit
It is necessary to clean the interior of the equipment once a month or more
frequently depending on use. Turn off and unplug the detector before proceeding
with this operation.
Use compressed air to remove dust from inside.
Use a Cleaning Card to remove dust particles adhering to the magnetic heads.
c) Additional recommendations.
The equipment needs to be placed in a clean, dust free environment.
Solution to Operational Problems
cont.
4.2 Maintenance
CAUTION: Before performing any cleaning process, turn off the equipment and unplug it. Please
note that problems or defects caused by lack of maintenance are not covered under the warranty.

14
Solution to Operational Problems
cont.
4.3 Jamming
-Ensure there are no foreign objects that could accidentally fall into the
equipment (clip, tape, etc. )
- To avoid jamming the bills, position them correctly in the feeding channel.
- Make sure the bill does not have adhesive tape.
-The bill cannot be very wrinkled or torn.
- If any bill or other object accidentally jams inside the detector:
1. Turn off the detector immediately.
2. Carefully proceed to remove the bill or object causing the problem.
3. Turn on the detector again and verify it is working at an optimum level.
1. Turn on the detector and insert a magnetic head cleaning card through the
detection channel as if you were going to check a regular bill.
2. Pass the cleaning card several times to help remove dust that is adhering to
the surface of the magnetic heads. Wait about two minutes before
proceeding to check bills again.
4.4 Cleaning of Magnetic Heads

15
Solution to Operational Problems
cont.
4.5 IR Sensor Calibration
1. Use conventional 80g office paper and cut it to the size of a USD bill
(6 x 2.5 inch) to calibrate the equipment.
2. Turn on the unit.
3. Pass the white paper as if to scan a bill.
4. Place the paper all the way to the left edge of the equipment to activate
the feeding motor, but do not let the paper touch the feeding belts. Keep
the motor sensor activated for a few seconds until the motor stops and
emits a four beep warning, then remove the paper.
5. Insert the paper into the detection channel this time as if scanning a
bill, the unit will begin flashing both indicators intermittently, keep the
paper inside for a few seconds while calibrating the IR sensors.
6. After the calibration is complete, the unit will give a two-beep warning
and turn off the red indicator.
7. Turn off the detector and remove the paper.

16
5.Software Updates
1. Copy the programming software to a mini SD card.
2. Turn off the detector.
3. Insert the mini SD card into the update port at the back of the unit as the image
shown.
4. Turn on the detector. The two LED indicators in the display will flash
intermittently during the programing process.
5. Wait approximately 30 seconds until the detector finishes the update. The red
indicator will turn off to show that the new software installation is complete.
6. Turn off the detector and remove the SD card.
7. Turn on the detector and check the update.
Steps to perform software update:
SD

17
All support provided from our North
American office Monday - Friday
9:00 am - 5:00 PM EST
1-888-993-2228
[e-mail]
6.Specifications
Temperature: 32° - 104°F (0° - 40°C)
Humidity: 25% - 80%%
Display: LED indicator
Processing Speed: Less than 1 second (Approx.)
Power Adapter: Input 100 - 240V AC / 50-60 Hz 0.6A
Output 12V DC / 1.0 A
Power Consumption: < 5W
Dimensions: 5.7 in x 5.9 in x 3 in (14.5 x 15 x 7.6 cm)
Weight: 1.15 lbs (0.52 Kg)

www.accubanker.com

www.accubanker.com
porque su dinero cuenta

17
7. Especificaciones
Temperatura Ambiente: 32° - 104°F (0° - 40°C)
Humedad Ambiente: 25 % - 80 %%
Velocidad de Operación: Menos de 1 segundo (Aprox)
Fuente de Alimentación: Voltaje de Entrada: 100V-240V 60 / 50Hz
Voltaje de Salida: 12V / 1A
Batería: Batería de litio recargable 11V / 1A (Batería opcional se vende por separado)
Consumo de Energía: < 5W
Dimensiones: 5.7 in x 5.9 in x 3 in (14.5cm x 15cm x 7.6cm )
Peso: 1.15lbs (0.52 Kg)
Apoyo tecnico en nuestra oficina de
Norte America
Lunes - Viernes
9:00 AM - 5:00 PM EST
1-888-993-2228
[e-mail]