Ace Plus EX-G011 User manual

EX-G011
4x4 HDMI over CAT5 Matrix with
IR Control Path
User Manual
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
Page 1 of 22

Safety and Notice
The EX-G011 4x4 HDMI over CAT5 Matrix with IR Control Path has been tested for
conformance to safety regulations and requirements, and has been certified for international use.
However, like all electronic equipments, the EX-G011 should be used with care. Please read and
follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage
to the unit.
zFollow all instructions and warnings marked on this unit.
zDo not attempt to service this unit yourself, except where explained in this manual.
zProvide proper ventilation and air circulation and do not use near water.
zKeep objects that might damage the device and assure that the placement of this unit is on a
stable surface.
zUse only the power adapter and power cords and connection cables designed for this unit.
zDo not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device
before cleaning.
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
Page 2of 22

Introduction
Introduction
HDMI cable
4x HDMI Source
PS3
Blu- ray Disc
TiVo
HD
MI
2x CAT5e
4x HDTV
EX-G011RX
IR controller
IR receive
r
EX-G011RX
EX-G011RX
EX-G011RX
The EX-G011 4x4 HDMI over CAT5 Matrix with IR Control Path provides the most flexible and
cost effective solution in the market to route high definition video sources plus multi-channel (up to
7.1-channel) digital audio from any of the four HDMI sources to the remote displays at the same time.
Through low cost CAT5/5e LAN cables, not only high quality video and audio can be transmitted to the
display sites, but also users can switch among 4 HDMI sources using the push button or remote
control. With single power design at the source site, each remote module is easily installed without
power supply. Furthermore, the built-in IR extension function makes users at display site access the
DVD player, PS3 or any HDMI equipped devices directly!
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
Page 3of 22

Features
zState-of-the-art Silicon Image (founder of HDMI) chipset embedded for upmost compatibility and
reliability
zHDMI 1.2a compliant
zHDCP compliant
zAllows any source to be displayed on multiple displays at the same time
zAllows any HDMI display to view any HDMI source at any time
zSupports 7.1 channel digital audio
zSupports default HDMI EDID and learns the EDID of displays
zThe matrix master can switch every output channels to any HDMI inputs by push button, IR
remote control, or RS-232 control
zAllows controlling local HDMI sources such as DVD and TiVo by IR extender through control path
at remote receiver
zAllows to control main matrix center through control line at remote receiver
zExtends video signal up to 35m (115 feet) over CAT5e at 1080p
zEasy installation with rack-mounting and wall-mounting designs for master and receiver
respectively
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
Page 4of 22

Specifications & Package Contents
Model Name EX-G011
Technical EX-G011 EX-G011RX
Role of usage True 4x4 matrix & transmitter [TX] Receiver [RX]
HDMI compliance HDMI 1.2a
HDCP compliance Yes
Video bandwidth Single-link 165MHz [4.95Gbps]
Video support 480i / 480p / 720p / 1080i / 1080p60
Audio support Surround sound (up to 7.1ch) or stereo digital audio
Transmission Full HD (1080p): 35m (115ft) [CAT5e] / 40m (130ft) [CAT6]
HD (720p/1080i): 50m (165ft) [CAT5e] / 55m (180ft) [CAT6]
Equalization N/A 8-level digital control
Input TMDS signal 1.2 Volts [peak-to-peak]
Input DDC signal 5 Volts [peak-to-peak, TTL]
ESD protection
[1] Human body model — ±15kV [air-gap discharge] & ±8kV [contact
discharge]
[2] Core chipset — ±8kV
PCB stack-up 4-layer board [impedance control — differential 100Ω; single 50Ω]
Input 4x HDMI
1x RS-232
1x RJ-45 TMDS
1x RJ-45 DDC
1x IR socket for IR receiver
Output
4x RJ-45 TMDS
4x RJ-45 DDC
5x IR socket for IR emitter
1x HDMI
HDMI Input selection Push button / IR remote / RS-232 Push button / IR remote
HDMI source control Controllable through IR control path from IR receiver at receiver sites
IR remote control Electro-optical characteristics: τ= 25°/ Carrier frequency: 38kHz
HDMI connector Type A [19-pin female]
RJ-45 connector WE/SS 8P8C with 2 LED indicators [TMDS & DDC channels]
RS-232 connector DE-9 [9-pin D-sub female]
3.5mm connector
Earphone jack for IR emitter cable
[IR Main] All sources IR control
[IR1~IR4] Individual channel IR control
Earphone jack for IR receiver
cable
[IR] Receives IR control
DIP switch
[for EX-G011 only]
[SW1~SW4] 2-pin for EDID, audio mode & safe mode
[SW Main] 4-pin operation mode & firmware update
Mechanical EX-G011 EX-G011RX
Housing Metal case
Model 340 x 110 x 44mm [1’1.4”x4.3”x1.7”] 85 x 90 x 25mm [3.3”x3.5”x1”]
Package 545 x 230 x 110mm [1’9.5”x9.1”x4.3”]
Dimension
s
(L x W x H) Carton 570 x 580 x 260mm [1’10.5”x1’10.9”x10.2”]
Model 1220g [2.7 lbs] 180g [6.3 oz]
Weight Package 3.2 kg [7.0 lbs]
Fixedness 1U rack-mount with ears
Wall hanging holes
W
all-mount with screws
Power supply 5V 6A DC Not necessarily required1
Power consumption 20 Watts [max] 1 Watt [max] (provided by
EX-G011)
Operation 0~40°C [32~104°F]
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
Page 5of 22

temperature
Storage temperature -20~60°C [-4~140°F]
Relative humidity 20~90% RH [no condensation]
Package Contents
1x EX-G011
1x IR emitter cable2
2x Rack-mounting ears
1x IR remote2
1x User Manual
4x EX-G011RX
4x IR receiver cable
8x Wall-mounting screws
1x 5V 6A power adapter
1The EX-G011RX has been tested extensively and found that it doesn’t require external power
supply. If in rare situation you find it cannot work with the EX-G011, please use any +5V power
adapter to plug in the power jack and see if it can work. If not, please contact your technical
support for further service.
2Additional IR remote control and IR emitter cable can be purchased as optional accessories to
control the HDMI sources located separately.
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
Page 6of 22

Panel Descriptions
EX-G011
3
3
2 1 6 5 4
1. Power: Power indicator LED
2. IR: IR receiver
3. Input: Input source indicator LED
4. HP1–HP4: Connection status indicator LED for each output channel
5. Port1–Port4: Input source channels mapping LED for each output channel
6. Port1 Select–Port4 Select: Push button for selecting input channel
7.ON–OFF: Power ON/OFF
8.RS-232: RS-232 control port
9.+5V DC: 5V DC power jack
10.SW Main: DIP switches (see DIP Switch section in p.7)
11.SW1–SW4: DIP switch (see DIP Switch section in p.7)
12.IN1–IN4: HDMI inputs
13.IR1–IR4: IR extender jacks for individual HDMI source control
14.OUT1–OUT4: RJ-45 TMDS/DDC outputs for each output channel
15.IR Main: IR extender jack for all HDMI source control (default socket for IR emitter)
7 8 9 14
10 12
11 13 15
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
Page 7of 22

SW1-SW4 for EDID/Audio
DIP Switch
Position
Pin#1 Pin#2 Video Audio Description
OFF
[©]OFF [©]1080p Stereo1Default Mode2– 1080p & stereo audio output for most
HDTVs
OFF
[©]ON [ª] 720p
1080i Stereo
Safe Mode3– Enforce the system output at 720p/1080i
video and stereo audio for basic compatibility among
HDTVs
ON [ª] OFF [©]Bypas
s4Bypass4EDID Learning Mode5– for learning EDID from the
display while playing any received HDMI audio format
ON [ª] ON [ª]Bypas
s Stereo
EDID Learning & Stereo Mode5– for learning EDID from
the display while enforcing stereo output if any HDTV
cannot play surround sound normally
Note
1If the HDTV shows video but without audio, please try to set audio mode to stereo.
2Factory default of SW1-SW4: Pin#1-OFF [©] & Pin#2- OFF [©] for 1080p with stereo.
3If you encounter any unsolved audio/video output problem during system installation,
please turn any SW1-SW4 to Pin#1-OFF[©] & Pin#1-ON[ª], for safe mode to enforce the
most compatible 720p stereo output for system check.
4Bypass means the matrix will maintain playing the original format of HDMI signals in video
and perhaps audio. By setting at this mode, the users may encounter compatibility issue
among different kinds of HDMI sources and displays. If you cannot get the audio and/or
video output normally at the system installation, please change the DIP switch setting to
default mode or even safe mode to verify the functionality of the device.
5Set Pin#1 at ON[ª]first then connect the HDMI Input to HDTV through a HDMI cable. Wait
for 20 seconds. The EDID learning procedure will be finished. If you want to learn the EDID
from another HDTV, you must set Pin#1 at OFF[©]first and repeat this procedure.
DIP Switch
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
Page 8of 22

SW1-SW4 for EDID/Audio
DIP Switch
Position
Pin#1 Pin#2 Video Audio Description
OFF
[©]OFF [©]1080p Stereo1Default Mode2– 1080p & stereo audio output for most HDTVs
OFF
[©]ON [ª] 720p 1080i Stereo
Safe Mode3– Enforce the system output at 720p/1080i
video and stereo audio for basic compatibility among
HDTVs
ON [ª] OFF [©]Bypas
s4Bypass4EDID Learning Mode5– for learning EDID from the
display while playing any received HDMI audio format
ON [ª] ON [ª]Bypas
s Stereo
EDID Learning & Stereo Mode5– for learning EDID from
the display while enforcing stereo output if any HDTV
cannot play surround sound normally
Note
1If the HDTV shows video but without audio, please try to set audio mode to stereo.
2Factory default of SW1-SW4: Pin#1-OFF [©] & Pin#2- OFF [©] for 1080p with stereo.
3If you encounter any unsolved audio/video output problem during system installation,
please turn any SW1-SW4 to Pin#1-OFF[©] & Pin#1-ON[ª], for safe mode to enforce the
most compatible 720p stereo output for system check.
4Bypass means the matrix will maintain playing the original format of HDMI signals in video
and perhaps audio. By setting at this mode, the users may encounter compatibility issue
among different kinds of HDMI sources and displays. If you cannot get the audio and/or
video output normally at the system installation, please change the DIP switch setting to
default mode or even safe mode to verify the functionality of the device.
5Set Pin#1 at ON[ª]first then connect the HDMI Input to HDTV through a HDMI cable. Wait
for 20 seconds. The EDID learning procedure will be finished. If you want to learn the EDID
from another HDTV, you must set Pin#1 at OFF[©]first and repeat this procedure.
DIP Switch
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
Page 9of 22

SW Mainfor firmware update (for technical support only)
DIP Switch Position Pin#1 Pin#2 Pin#3 Pin#4
Normal Operation
Mode6 OFF [©]OFF [©]ON [ª]OFF [©]
Firmware Update
Mode7ON [ª]ON [ª]OFF [©]OFF [©]
Note
6Factory default for SW Main: Pin#1-OFF [©], Pin#2-OFF[©], Pin#3-ON [ª], Pin#4-OFF[©].
PLEASE MAINTAIN THIS SETTING AT ANYTIME FOR REGULAR USE!
7Sequence for firmware update
[1]. Power off the EX-G011.
[2]. Set the DIP switch position to Firmware Update Mode.
[3]. Power on the EX-G011.
[4]. Power off the EX-G011.
[5]. Set the DIP switch position to Normal Operation Mode.
[6]. Power on the EX-G011.
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
Page 10of 22

IR Control Pat
IR Cables
IR Emitter Cable IR Receiver Cable
IR Sockets
EX-G011
IR Main: The default location for IR emitter extension cable to transmit all IR command signals received
from any of the four remote receivers to all of the HDMI sources.
IR1: IR emitter extension cable connected here can only transmit IR command signals from the remote
receivers that are setting at the input channel 1.
IR2: IR emitter extension cable connected here can only transmit IR command signals from the remote
receivers that are setting at the input channel 2.
IR3: IR emitter extension cable connected here can only transmit IR command signals from the remote
receivers that are setting at the input channel 3.
IR4: IR emitter extension cable connected here can only transmit IR command signals from the remote
receivers that are setting at the input channel 4.
EX-G011RX
IR: IR receiver cable connected here can receive all IR command signals from the IR remote controls of
EX-G011 and all other HDMI source machines.
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
Page 11of 22

Definition of IR Earphone Jack
IR Emitter IR Receiver
You can buy any IR extension cables in the market that are compatible to the definition of the
IR sockets for the matrix if necessary for replacement use.
Supported IR Data Format
Data Format Suitable Not Recommended
NEC 5
RC5 5
TOSHIBA MICOM
CODE 5
GRUNDIG CODE 5
SONY 12 BIT CODE 5
SONY 15 BIT CODE 5
SONY 20 BIT CODE 5
RCA CODE 5
RCM CODE 5
MATSUSHITA CODE 5
MITSUBISHI CODE 5
ZENITH CODE 5
JVC CODE 5
M50560-001P 5
MN6125H 5
MN6125L 5
MN6014_C5D7 5
MN6014-C6D6 5
MC14457P 5
LC7464(AHEA) 5
GEMINI_CM 5
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
Page 12of 22

Hardware Installation
EX-G011 as master
1. Connect all sources to HDMI Inputs on the 4x4 HDMI over CAT5 matrix master EX-G011
2. Connect each DDC output on the EX-G011 to respective DDC input on the remote receiver
EX-G011RX
3. Connect each TMDS output on the EX-G011 to respective TMDS input on the remote receiver
EX-G011RX
4. Connect IR emitter cable to the EX-G011 and direct the IR emitter to the build-in IR receiver of the
sources
5. Connect the +5V 6A DC power supply to the EX-G011
6. Power on all HDMI sources
7. Power on the EX-G011
EX-G011RX as receiver
1. Connect each HDMI output to HDMI displays
2. Connect the TMDS input on the EX-G011RX to the TMDS output on the EX-G011
3. Connect the DDC input on the EX-G011RX to the DDC output on the EX-G011
4. Connect IR receiver cable and place the IR receiver at the appropriate position that can receive
the IR signals sent from the users
5. Use push button to adjust the EQ until the picture and sound are clear
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
Page 13of 22

Operation and IR Control
Source Side
Method A: Push Button
Push the switch button on the front panel, the source will be sequentially changed.
Method B: IR Remote Control
a. Please press to enter IR control mode
Note
If EX-G011 receives the IR commands, the LED will flash. If not, try again.
b. Decide which output port to be controlled by pressing F1 to F4, and wait a few seconds for
audio/video of next channel coming out after the channel switch command is sent.
Note
If the setting is correct, the corresponding LED will flash. If not, please press output port select
button or repeat step (a) and (b).
F1 HDMI output #1
F2 HDMI output #2
F3 HDMI output #3
F4 HDMI output #4
c. Use or keys to select input source, and wait a few
seconds for audio/video of next channel coming out after the
channel switch command is sent.
Note
If the setting is correct, the corresponding LED will flash. If there
is no response, please wait until the LED stops flashing, and try
again.
Left button to switch channels in ascending order (1, 2, 3, 4, 1, ...)
Right button to switch channels in descending order (1, 4, 3, 2, 1, …)
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
Page 14of 22

Display Side
Method A: Push button
Push the switch buttons of respective output channels then the output channel will switch from HDMI
source 1 to source 4 in sequential order, and wait a few seconds for audio/video of next channel
coming out after the channel switch command is sent.
Method B1: IR remote control for switching input channels
a. Press Power on button to enable IR control function.
Note: If EX-G011RX receives the IR command, the LED will flash.
If not, try again.
b. Press hot key for input source:
F1 HDMI source #1
F2 HDMI source #2
F3 HDMI source #3
F4 HDMI source #4
Method B2: IR remote control for controlling the HDMI sources
Users can use the corresponding IR remote to control respective DVD player or any HDMI
compliant devices including EX-G011 itself with IR control at any display site.
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
Page 15of 22

RS-232 Serial Port Control
Method C: Software Control through RS-232
1
2 4
6
3
Scan: Push this button will trigger the automatic search over all the available COM ports (1-255). If
the matrix is detected, the message window below will show up.
5
1
Otherwise, an error message shows up to indicate no legal device can be found. Notice that
successful connection is only established if there exists at least one available COM port.
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
Page 16of 22

Open: Open the COM port after scan to establish the connection between PC and the matrix.
2
Close: Release the COM port after scan.
3
4 Quick Setup Buttons: Provide the fast setup between inputs and outputs of the matrix. “Default”
button makes input 1, 2, 3, 4 mapped to output 1, 2, 3, 4 respectively. “Channel 1” makes
all outputs see input-1, same for the remaining buttons.
Output Channel Setup: Click on this button, a quick selection table of inputs will show up. Users
can therefore easily select the input video for each output.
5
Input Channel Setup: The button will bring up the setup window for the inputs as below.
6
A
B
Input Channel: Select the input channel to do bitmap and label change.
C
A
BBitmap Path: Select the figure for each channel. Notice that only pictures in BMP format are
supported.
C
Description: Channel description.
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
Page 17of 22

RS-232 Commands
RS-232 transmission Format
Baud rate: 9600
Data bit: 8
Parity: None
Set Command
Command Code Response Description
Data Check SUM ACK SET
0x08 0x4d 0x41 0x51 0x44 0x05
*0x01~0xff
0x31~0x2f 0xaa SET EX-G011 Device
ID
0x0c 0x4d 0x41 0x51 0x44
Device_Id 0x02 port1 port2 port3
port4
0x0c+…+port4 0xaa Set EX-G011 Source
Mapping of Output Port
Status Command
Command Code Response Description
Data Check
SUM Get Status Check SUM Status
0x05 0x4d 0x4f 0x44 0xe5 0xaa 0x06 0x4d
0x41 0x51 0x44 0x29 Get Device Type (EX-G011)
0x07 0x4d 0x41 0x53
0x57 0x04 0x43 0xaa 0x3 0x01~0xff 0x04~0x02 Get Device ID
0x08 0x4d 0x41 0x51
0x44 *0x01~0xFF 0x01
0x2e~0x2
c
0xaa 0x06 port1
port2 port3 port4
0x06 +
port1~port4
Get Source Mapping o
f
Output Port
0x08 0x4d 0x41 0x51
0x44 *0x01~0xFF 0x04
0x30~0x2
e
0xaa 0x08 0x56
0x33 0x2e 0x30
0x31 0x61
0x81 Software Version
V.3.01a
Check sum:
Check sum = (Data value sum)%256 The check sum of response is not included 0xaa.
0x01 ~ 0xFF:
This data is device ID. The Device ID saved in the device, if the device ID of the controlled device
is 0xff , the device will ignore its own ID and carry out the commands.
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
Page 18 of 22

Firmware Update
Warning!
There could be unexpected consequences resulted from inappropriate firmware update
operation. Please do it with caution.
1. Please unzip the Matrix_Firmware_Update.zip into your designated folder.
2. Please turn off the power of the MATRIX and set DIP location of [SW Main] at Pin#1-ON(ª),
Pin#2-ON(ª), Pin#3-OFF(©), & Pin#4-OFF(©).
3. Please execute the file Matrix_Firmware_Update.exe
4. In the pop-up window, at [Select Chip], please select W78E365.
5. In the pop-up window, at [Select File], please choose the BIN file in the designated folder, as
shown in the picture.
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
Page 19of 22

6. In the pop-up window, please select the [File Format] to Binary.
7. Please make sure your PC has direct connection to the RS-232 port of the MATRIX, as shown in
the picture (left), that in [Communication Setting] the onlne status should be “Wait to connect”. If
the RS-232 connection is not firmly established, you will see the online status is “Disconnect.” If so,
please check the RS-232 connection until the online status becomes “Wait to Connect.”
8.
Please turn on the MATRIX. The firmware update process will automatically initiate.
9. The firmware update process is successful if you see the [Information] window pops up to inform
you that the process is complete. If you see the [Error] window pops up, please turn off the
MATRIX and turn it on again. If necessary, please redo the whole sequences 1-9.
10. The message “Program: OK!” means the firmware update process is successful. If you see the
[Error] window pops up after the message [Program: OK!], please ignore it.
11. Turn off MATRIX. Set DIP location of [SW Main] at Pin#1-OFF(©), Pin#2-OFF(©), Pin#3-ON(ª),
& Pin#4-OFF(©).
12. Turn the MATRIX back on and return to normal operation.
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 Jung Shing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
Page 20 of 22