Planet FGSW-2022VHP User manual

12-Port 10/100TX 802.3at PoE + 4-Port 10/100TX 802.3bt
PoE + 2-Port Gigabit TP + 2-Port SFP Ethernet Switch with
LCD Management
FGSW-2022VHP
User’s Manual

Copyright
Copyright © 2019 by PLANET Technology Corp. All rights reserved. No part of
this publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form or
by any means, electronic, mechanical, magnetic, optical, chemical, manual or
otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied,
with respect to the contents hereof and specically disclaims any warranties,
merchantability or tness for any particular purpose. Any software described
in this manual is sold or licensed "as is". Should the programs prove defective
following their purchase, the buyer (and not PLANET, its distributor, or its dealer)
assumes the entire cost of all necessary servicing, repair, and any incidental or
consequential damages resulting from any defect in the software. Further, PLANET
reserves the right to revise this publication and to make changes from time to time
in the contents hereof without obligation to notify any person of such revision or
changes.
All brand and product names mentioned in this manual are trademarks and/or
registered trademarks of their respective holders.
Trademarks
PLANET is a registered trademark of PLANET Technology Corp. All other
trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all
environments and applications, and makes no warranty and representation, either
implied or expressed, with respect to the quality, performance, merchantability, or
tness for a particular purpose.
PLANET has made every eort to ensure that this User’s Manual is accurate;
PLANET disclaims liability for any inaccuracies or omissions that may have
occurred. Information in this User’s Manual is subject to change without notice
and does not represent a commitment on the part of PLANET. PLANET assumes
no responsibility for any inaccuracies that may be contained in this User’s Manual.
PLANET makes no commitment to update or keep current the information in this
User’s Manual, and reserves the right to make improvements to this User’s Manual
and/or to the products described in this User’s Manual, at any time without notice.
If you nd information in this manual that is incorrect, misleading, or incomplete,
we would appreciate your comments and suggestions.

FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the Instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
WEEE Warning
To avoid the potential eects on the environment and human health as a
result of the presence of hazardous substances in electrical and electronic
equipment, end users of electrical and electronic equipment should
understand the meaning of the crossed-out wheeled bin symbol. Do not
dispose of WEEE as unsorted municipal waste; WEEE should be collected
separately.
Revision
PLANET 12-Port 10/100TX 802.3at PoE + 4-Port 10/100TX 802.3bt PoE + 2-Port
Gigabit TP + 2-Port SFP Ethernet Switch with LCD Management User's Manual
Model: FGSW-2022VHP
Revision: 1.0 (Aug., 2019)
Part No.: 2351-AK5110-000

Table of Contents
1. Introduction................................................................................................. 5
1.1 Package Contents .................................................................................. 5
1.2 Product Description ................................................................................ 6
1.3 Features ............................................................................................... 8
1.4 Specications .......................................................................................10
2. Hardware Description ..................................................................................12
2.1 Front Panel ..........................................................................................12
2.1.1 CD Monitor Indicators.................................................................13
2.1.2 LED Indicators ...........................................................................14
2.2 Rear Panel ...........................................................................................15
2.3 LCD Management .................................................................................16
2.3.1 Switch Mode ..............................................................................17
2.3.2 Budget Control...........................................................................19
2.3.3 PSE Port Priority.........................................................................19
2.3.4 PSE Port Enable .........................................................................20
2.3.5 PD Type ....................................................................................20
2.3.6 Alive Check ...............................................................................21
2.3.7 Bandwidth Detection...................................................................22
2.3.8 Fan Control................................................................................22
2.3.9 Screen Saver .............................................................................23
2.3.10 Language ..................................................................................23
2.3.11 Default Setting...........................................................................23
2.3.12 Password Setting........................................................................24
2.3.13 System .....................................................................................24
3. Hardware Installation...................................................................................25
3.1 Desktop Installation ..............................................................................26
3.2 Rack Mounting......................................................................................27
3.3 Installing the SFP Transceiver ................................................................28
3.4 Product Applications..............................................................................30
3.5 Power over Ethernet Powered Devices ....................................................31
4. Power over Ethernet Overview .....................................................................32
5. Troubleshooting...........................................................................................35

5
1. Introduction
Thank you for purchasing PLANET FGSW-2022VHP 12-Port 10/100TX 802.3at PoE
+ 4-Port 10/100TX 802.3bt PoE + 2-Port Gigabit TP + 2-Port SFP Ethernet Switch
with LCD Management. “LCD Switch” is used as an alternative name in this user’s
manual.
1.1 Package Contents
Open the box of the LCD Switch and carefully unpack it. The box should contain
the following items:
LCD Switch x 1 User’s Manual x 1
Power Cord x 1 Rubber Feet x 4
Rack-mounting Brackets x 2 Screws x 8
If any of these pieces are missing or damaged, please contact your dealer
immediately.

6
1.2 Product Description
Just “Plug and Watch” for a Quick Solution
PLANET FGSW-2022VHP is an ideal Plug and Watch Power over Ethernet solution
which provides quick installation, real-time PoE work status monitoring and
immediate troubleshooting through its unique LCD display to improve work
eciency and quality without any PC or software required.
The FGSW-2022VHP is equipped with 12 10/100BASE-TX ports featuring 802.3at
Power over Ethernet Plus (PoE+) copper interfaces and 4 10/100BASE-TX ports
featuring 802.3bt PoE++ copper interfaces. With a total PoE power budget of up
to 300 watts and non-blocking data switching performance, the FGSW-2022VHP
fullls the demand of sucient PoE power for HD IP surveillance. It oers a
desktop-sized, reliable and visible power solution for small businesses and system
integrators deploying Power over Ethernet networks.
Smart and Intuitive LCD Control
The FGSW-2022VHP provides an intuitive color panel on its front panel that
facilitates the Ethernet management and PoE PD management. They greatly
promote management eciency in large-scale network, such as enterprises, hotels,
shopping malls, government buildings and other public areas, and feature the
following special management and status functions:
PoE management and status
Port management and status
Switch mode includes Standard, VLAN or Extend
PD type: 802.3bt, UPoE, Legacy
Budget and bandwidth control
PD alive check
Screen saver, fan control and factory default
Security password
Standard, VLAN or Extend Operation Mode
The FGSW-2022VHP provides Standard, VLAN or Extend operation mode. The
FGSW-2022VHP operates as a normal IEEE 802.3at/bt PoE switch in the Standard
operation mode.

7
Standard Mode (default)
SwitchMode
Options:
VLAN
Extend
Standard>
<UP>/<Down>:Select
<Enter>:Confirm<Back>:Retur n
Current Settin g: Standa rd
Power
PoE
100 meters (328 feet)
LCD PoE Switch
PoE
100BASE-TX UTP with PoE
PoE IP Camera
> Standard
VLAN
Extend
> Standard
VLAN
Extend
The VLAN operation mode features the port-based VLAN function that can help to
prevent the IP camera’s multicast or broadcast storm from inuencing each other.
VLAN Isolation Mode
Ports 17~20 for Uplink
Ports 1~16 Access Permitted
LCD PoE Switch
PC
Ports 1 to 16
Access Denied
PoE
PoE
PoE
1000
1000BASE-SX/LX Fiber Optic
1000
100BASE-TX UTP
PoE
100BASE-TX UTP with PoE
IP Camera
IP Camera
IP Camera
NVR
SwitchMode
Options:
VLAN
Extend
Standard>
<UP>/<Down>:Select
<Enter>:Confirm<Back> :Return
Current Settin g: Standa rd
Standard
> VLAN
Extend
Standard
> VLAN
Extend
In the Extend operation mode, the FGSW-2022VHP operates on a per-port basis at
10Mbps duplex operation but can provide PoE power output over a distance of up
to 250 meters overcoming the 100m limit on Ethernet UTP cable. With this brand-
new feature, the FGSW-2022VHP provides an additional solution for 802.3at/bt PoE
distance extension, thus saving the cost of Ethernet cable installation. Its VLAN
isolation function isolates ports so as to prevent broadcast storm and defend DHCP
spoong in the Extend operation mode.
Extend Mode
Power
250 meters (820 feet)
PoE
LCD PoE Switch
PoE
10BASE-T UTP with PoE
PoE IP Camera
SwitchMode
Options:
VLAN
Extend
Standard>
<UP>/<Down>:Select
<Enter>:Confirm<Back>:Retur n
Current Settin g: Standa rd
Standard
VLAN
> Extend

8
Flexible Extension Solution
The two mini-GBIC slots built in the FGSW-2022VHP are compatible with the
100/1000BASE-X SFP (small form-factor pluggable) ber transceiver, uplinked
to the backbone switch and monitoring center in long distance. The distance can
be extended from 550 meters (multi-mode ber) to 10/20/30/40/50/60/70/120
kilometers (single-mode ber or WDM ber). They are well suited for applications
within the enterprise data centers and distributions.
Robust Protection
The FGSW-2022VHP provides contact discharge of ±6KV DC and air discharge
of ±8KV DC for Ethernet ESD protection. It also supports ±6KV surge immunity
to improve product stability and protects users’ networks from devastating ESD
attacks, making sure the ow of operation does not uctuate.
Easy Installation and Cable Connection
As data and power are transmitted over one cable, the FGSW-2022VHP does not
need a second cable and electrical outlets on the wall, ceiling or any unreachable
place. Thus, it helps to lower the installation costs and simplify the installation
eort. All the RJ45 copper interfaces of the FGSW-2022VHP support 10/100Mbps
auto-negotiation for optimal speed detection through RJ45 Category 5e/6 cable. It
also supports standard auto-MDI/MDI-X that can detect the type of connection to
any Ethernet device without requiring special straight-through or crossover cables.
1.3 Features
Physical Port
16-port 10/100BASE-TX Fast Ethernet RJ45 copper
2 10/100/1000BASE-T TP and 2 100/1000BASE-X mini-GBIC SFP interfaces
Power over Ethernet
Complies with IEEE 802.3at/bt Power over Ethernet PSE
Selectable PoE mode: IEEE 802.3bt/UPoE/Legacy
Ports 1 to 4 support up to 60 watts; ports 5 to 16 support up to 32 watts
Each port supports 54V DC power to PoE powered device
300-watt PoE budget
Auto detects powered device (PD)
Circuit protection prevents power interference between ports
Remote power feeding up to 100m in standard mode and 250m in extend
mode

9
Smart LCD
The LCD switch features “Standard”, “VLAN” or “Extend” mode selection;
the “Extend” mode features about 45-/20-watt PoE transmission distance of
250m at speed of 10Mbps and VLAN isolation
The LCD switch is able to isolate ports to prevent broadcast storm and defend
DHCP spoong
Power low-voltage, power over-voltage and PSE over-temperature protection
Security password, screen saver, fan control, factory default and save congu-
ration
PoE management
- Total PoE power budget control
- Per port PoE function enable/disable
- PoE port power feeding priority
- Per PoE port power limitation
- PD alive check
Switching
Hardware-based 10/100/1000Mbps auto-negotiation and auto MDI/MDI-X
Flow control for full duplex operation and back pressure for half duplex
operation
9K Frame size
Integrates address look-up engine, supporting 8K absolute MAC addresses
Automatic address learning and address aging
Hardware
19-inch rack mountable size, 1U height
2-inch color LCD with smart management functions
LED indicators for system power, per port PoE ready and PoE activity, speed,
Link/Act
3 silent fans to provide stable and ecient power performance
Supports contact discharge of ±6KV DC and air discharge of ±8KV DC for
Ethernet ESD protection
Supports ±6KV surge immunity

10
1.4 Specications
Model FGSD-2022VHP
Hardware Specications
Copper Ports
16 10/100BASE-TX RJ45 auto-MDI/MDI-X ports with
port-1 to port-16
2 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports with
port-1 to port-16
SFP/mini-GBIC Slots 2 100/1000BASE-X SFP interfaces with port-19 to
port-20
PoE Injector Port
4 ports with 802.3bt PoE++ injector function with
port-1 to port-4
12 ports with 802.3at PoE+ injector function with port-5
to port-16
Switch Architecture Store-and-Forward
Switch Fabric 11.2Gbps/non-blocking
Throughput
(packet per second) 8.3Mpps@64 bytes packet
MAC Address Table 8K entries
Jumbo Frame 9K bytes
Flow Control IEEE 802.3x pause frame for full duplex; back pressure
for half duplex
LED Indicators
System:
Power (Green)
10/100BASE-TX RJ45 Interfaces:
10/100Mbps LNK/ACT (Green)
PoE-in-Use (Amber)
100/1000BASE-X SFP Interfaces:
LNK/ACT (Green)
100Mbps (Red)
1000Mbps (Green)
10/100/1000BASE-T TP Interfaces
LNK/ACT (Green)
100Mbps (Red)
1000Mbps (Green)
LCD Monitor (W x D) 40.6 x 30.5 mm, 2-inch
Buttons Menu, Enter, Back, Up and Down
Dimensions (W x D x H) 233 x 440 x 44 mm (1U height)
Enclosure Metal
Weight 3.3kg

11
Power Requirements 100~240V AC, 50/60Hz, 5A max.
Power Consumption/
Dissipation Max. 330watts/1132 BTU
Thermal Fan 3
ESD Protection Contact discharge of ±6KV DC
Air discharge of ±8KV DC
Surge Protection ±6KV
Power over Ethernet
PoE Standard IEEE 802.3bt PoE++ PSE (Port 1-4)
IEEE 802.3af/at PoE+ PSE (Port 5-16)
PoE Power Supply Type 802.3bt/UPoE/Legacy (Port 1-4)
End-span (Port 5-16)
PoE Power Output Per PoE++ port 54V DC, 1.2A. max. 60 watts
Per PoE+ port 54V DC, 600mA. max. 32 watts
Power Pin Assignment 802.3bt: 1/2 (-), 3/6 (+), 4/5 (+), 7/8 (-)
End-span: 1/2 (+), 3/6 (-)
PoE Power Budget 300 watts
Max. Number of Class 2/
Class 3 PDs 16
Max. Number of Class
4 PDs 11
Max. Number of Class 5/
Class 6 PDs 4
Standards Conformance
Regulatory Compliance FCC Part 15 Class A, CE
Standards Compliance
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab Gigabit 1000BASE-T
IEEE 802.3z Gigabit SX/LX
IEEE 802.3x Flow Control and Back Pressure
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
IEEE 802.3bt PoE++ (Type 3)
Environment
Operating Temperature: -10 ~ 60 degrees C
Relative Humidity: 5 ~ 90% (non-condensing)
Storage Temperature: -15 ~ 70 degrees C
Relative Humidity: 5 ~ 90% (non-condensing)

12
2. Hardware Description
These switches provide three dierent running speeds – 10Mbps, 100Mbps and
1000Mbps and automatically distinguish the speed of the incoming connection. This
section describes the hardware features of LCD Switch. For easier management
and control of the LCD Switch, familiarize yourself with its display indicators and
ports. Front panel illustrations in this chapter display the unit LED indicators.
Before connecting any network device to the LCD Switch, please read this chapter
carefully.
2.1 Front Panel
The front panel of the LCD Switch consists of 4 10/100BASE-TX 802.3bt PoE++
ports, 12 10/100BASE-TX 802.3at PoE+ ports, 2 10/100/1000BASE-T RJ45 ports
and 2 additional 10/100BASE-X SFP ports. The LCD monitor and LED Indicators are
also located on the front panel of the LCD Switch.
6
5
8
7
10
9
12
11
14
13
16
15
FGSW-2022VHP
Menu (5 sec)
Enter
Back
1
PWR
Up
Down
5 9 13
3 7 11 15
PoE
2 6 10 14
4 8 12 16
PoE-in-Use
ACTLNK
Gigabit
17 19
18 20
ACTLNK
100 1000
18
17
20
19
12-Port 10/100TX 802.3at PoE +
4-Port 10/100TX
802.3bt PoE +
4-Port Gigabit Ethernet Switch
2 4
1 3
Figure 2-1: FGSW-2022VHP Front Panel
Fast Ethernet TP interface (Port 1 to Port 16)
10/100BASE-TX copper, RJ45 twisted-pair: Up to 100 meters.
Ports 1 to 4 support IEEE 802.3bt.
Ports 5 to 16 support IEEE 802.3at.
Gigabit TP Interface (Port 17 to Port 18)
10/100/1000BASE-T copper, RJ45 twisted-pair: Up to 100 meters.
Gigabit SFP Slots (Port 19 to Port 20)
10/100BASE-X mini-GBIC slot, SFP (Small Factor Pluggable) transceiver module:
From 550 meters (multi-mode ber) to 10/20/30/40/50/60/70/120 kilometers
(single-mode ber).
Smart LCD
The Smart LCD that is located on the front panel of the FGSW-2022VHP
provides “PoE Management and Status”, “Switch Mode: Standard, VLAN, Extend”,
“Budget and Bandwidth Control”, “PD alive check”, “Screen Saver”, “PD Type”,
“Password”, “Fan Control”, and “ Factory Default”.

13
2.1.1 CD Monitor Indicators
The LCD Switch has an LCD monitor designed for network administrator who can
easily obtain real-time per PoE port output watts information and system status
display, such as over voltage, low voltage, and PoE chipset over temperature
function. The details of each message on the LCD monitor are shown below:
Power Low-voltage Protection Power Over-voltage Protection PSE Over-temperature Protection
30.3
01 W ---M--- M
ULP
02 --- M---M
OLP
03 --- M--- M
SCP
04 --- M--- M
----W
05 --- M--- M
13.6
06 W --- M--- M
14.4
07 W --- M--- M
----
08 W -33 M--- M
----
09 W --- M-33 M
-OFF
10 - --- M--- M
----
11 W --- M--- M
----
12 W --- M--- M
----
13 W --- M--- M
----
14 W --- M--- M
PB:300W TP:0W PD:3
Switch Port Information
Switch Port Information
----
01 W ---M--- M
----
02 W --- M---M
----W
03 --- M--- M
----W
04 --- M--- M
----W
05 --- M--- M
----
06 W --- M--- M
----
07 W --- M--- M
----
08 W --- M--- M
----
09 W --- M--- M
----
10 W --- M--- M
----
11 W --- M--- M
----
12 W --- M--- M
----
13 W --- M--- M
----
14 W --- M--- M
WARNING！
Main supply voltage
is High！
All ports had shut-
down.
PD:0PB:300W TP:0W
----
01 W ---M--- M
----
02 W --- M---M
----W
03 --- M--- M
----W
04 --- M--- M
----W
05 --- M--- M
----
06 W --- M--- M
----
07 W --- M--- M
----
08 W --- M--- M
----
09 W --- M--- M
----
10 W --- M--- M
----
11 W --- M--- M
----
12 W --- M--- M
----
13 W --- M--- M
----
14 W --- M--- M
WARNING！
The PSE device is too
hot!
All ports had shut-
down.
Switch Port Information
PD:0PB:300W TP:0W
----
01 W ---M--- M
----
02 W --- M---M
----W
03 --- M--- M
----W
04 --- M--- M
----W
05 --- M--- M
----
06 W --- M--- M
----
07 W --- M--- M
----
08 W --- M--- M
----
09 W --- M--- M
----
10 W --- M--- M
----
11 W --- M--- M
----
12 W --- M--- M
----
13 W --- M--- M
----
14 W --- M--- M
WARNING！
Main supply voltage
is low！
All ports had shut-
down.
Switch Port Information
PD:0PB:300W TP:0W
PD light load protection
PD overload protection
Short-circuit protection
PoE Usage
Network traffic
PoE OFF
Power Budget Total PoE
Output
Number of PDs
Note
1. The LCD screens will refresh every 15 seconds.
2. For details on LCD Management feature, please refer to “2.3 LCD
Management”.

14
The detailed Smart LCD description of each item is shown below:
Parameters Description
30.3W
(example) It means the output power port of the PoE switch.
OLP It means the port is overloaded corresponding to the PSE, and the
port stops powering.
ULP
It means the port corresponding to the PSE is lightly loaded and
the port stops powering (When the current on the network is less
than 7.5mA, the PSE thinks the PD has been dialed out and the
port stops powering).
SCP It means the port corresponding to the PSE appears to be short-
circuited and the port stops powering.
OFF It means the white and blue OFF shows that the port is blocked by
the menu command.
---W It means the port is without a PD device insert.
---M It means this port does not have data transfers.
<1M It means this port data rate transfers less than 1M.
33M
(example)
The white and blue character represents the data transmission rate
while the red character represents the data transmission rate which
is greater than the bandwidth setting, causing power to restart the
PSE port. If the resumption situation happens for 10 times within 1
hour, the power supply to the port will be cut o.
PB It means power budget.
TB It means total PoE power output information.
PD The number of PDs inserted.
2.1.2 LED Indicators
System
LED Color Function
PWR Green Lights to indicate that the Switch has power.

15
10/100Mbps PoE Ports
LED Color Function
LNK/ACT Green
Lights Indicates the link through that port is successfully
established at 10/100Mbps.
Blinks Indicates that the Switch is actively sending or
receiving data over that port.
PoE-in-Use Amber
Lights Indicates the port is providing DC in-line power.
O Indicates the connected device is not a PoE
powered device (PD).
10/100/1000Mbps TP and 100/1000Mbps SFP Slots
LED Color Function
LNK/ACT Green
Lights Indicates the link through that port is successfully
established at 1000Mbps.
Blinks Indicates that the Switch is actively sending or
receiving data over that port.
100 Red Lights Indicates the port is successfully established at
100Mbps
1000 Green Lights Indicates the port is successfully established at
1000Mbps.
2.2 Rear Panel
The rear panel of the LCD Switch has an AC power socket (100 to 240V AC, 50-
60Hz, 5A).
100-240V , 50/60Hz, 5A max.
Figure 2-2: FGSW-2022VHP Switch Rear Panel

16
AC Power Receptacle
For compatibility with electrical outlet standard in most areas of the world, the LCD
Switch’s power supply automatically adjusts to line power in the range of 100-240V
AC and 50/60Hz, 2.5/5A.
Plug the female end of the power cord rmly into the receptacle on the rear panel
of the LCD Switch and the other end into an electrical outlet, and the power will be
ready.
Power
Notice
The device is a power-required device, which means it will not
work till it is powered. If your networks should be active all the
time, please consider using UPS (Uninterrupted Power Supply) for
your device. It will prevent you from network data loss or network
downtime. In some areas, installing a surge suppression device
may also help to protect your LCD Switch from being damaged by
unregulated surge or current to the Switch or the power adapter.
2.3 LCD Management
The operation of the 5 buttons (Menu, Enter, Back, Up and Down) on the panel:
Press the Menu button to switch the page of “Switch Port Information”.

17
Press the Menu button for about 5 seconds and enter the Main Menu. Choose
a menu item by scrolling up and down, and press the “Enter” key to get to the
menu item you have chosen. Press the “Back” key to return to the previous menu.
2.3.1 Switch Mode
There are three modes -- “Standard”, “VLAN” and “Extend” – for selection.
Switch Mode Description
Standard
(default)
This mode makes the LCD Switch operate as a general switch
and all PoE ports operate at 10/100Mbps auto-negotiation.
VLAN
This mode makes the LCD Switch operate as a VLAN isolation
switch and
1. Port 1 to port 16 will isolate respectively.
2. Port 1 to port 16 can only communicate with port 17~20
(uplink port).
Extend with
VLAN Isolation
This mode makes the LCD Switch operate as a VLAN isolation
switch and
1. Port 1 to port 16 will isolate respectively.
2. Port 1 to port 16 can only communicate with port 17~20
(uplink port).
3. Port 1 to port 4: 45-watt PoE transmit distance of 250m at
speed of 10Mbs.
Port 5 to port 16: 20-watt PoE transmit distance of 250m at
speed of 10Mbps.
Table 2-1: Switch Mode

18
Standard Mode (default)
SwitchMode
Options:
VLAN
Extend
Standard>
<UP>/<Down>:Select
<Enter>:Confirm<Back>:Return
Current Sett ing: Stand ard
Power
PoE
100 meters (328 feet)
LCD PoE Switch
PoE
100BASE-TX UTP with PoE
PoE IP Camera
> Standard
VLAN
Extend
> Standard
VLAN
Extend
VLAN Isolation Mode
Ports 17~20 for Uplink
Ports 1~16 Access Permitted
LCD PoE Switch PC
Ports 1 to 16
Access Denied
PoE
PoE
PoE
1000
1000BASE-SX/LX Fiber Optic
1000
100BASE-TX UTP
PoE
100BASE-TX UTP with PoE
IP Camera
IP Camera
IP Camera
NVR
SwitchMode
Options:
VLAN
Extend
Standard>
<UP>/<Down>:Select
<Enter>:Confirm<Back>:Return
Current Sett ing: Stand ard
Standard
> VLAN
Extend
Standard
> VLAN
Extend
Extend Mode
Power
250 meters (820 feet)
PoE
LCD PoE Switch
PoE
10BASE-T UTP with PoE
PoE IP Camera
SwitchMode
Options:
VLAN
Extend
Standard>
<UP>/<Down>:Select
<Enter>:Confirm<Back>:Retu rn
Current Sett ing: Stand ard
Standard
VLAN
> Extend

19
2.3.2 Budget Control
Due to the power allocation strategy of PSE, when the residual power of PoE is
too large, the power distribution of the port can be increased as much as possible
by increasing the power trimming of the PSE, so that the utilization of the PSE
power supply can be improved. There are four levels of budget control named
Unchanged (default), Add 5% PB, Add 10% PB and Add 15% PB.
Note
1. The default PoE budget is 300W. If you hope to have a full load
of over 300W, please select Add 5% PB, Add 10% PB or Add
15% PB.
2. In order to make sure the PSE power supply is not overloaded for a long
time, please try to ensure that TP is less than PB.
2.3.3 PSE Port Priority
The Priority represents PoE ports priority. There are three levels of power priority
named Low, High and Critical. The priority is used in case the total power
consumption is over the total power budget. In this case the port with the lowest
priority will be turned off, and offer power for the port of higher priority. The
default port priority is “Low”.

20
2.3.4 PSE Port Enable
Allows user to disable or enable per port PoE function. The default is “Enable”.
2.3.5 PD Type
Changing the PoE power-up mode can let non-standard PDs pass the procedures
of PoE power delivery process. This way, the switch can supply power to non-
standard PDs. The FGSW-2022VHP can be set as UPoE mode, 802.3bt mode or
Legacy mode.
The function only works on the port 1 to port 4.
Object Description
UPoE Regardless of PD's class rating, PSE will provide the maximum
power for PD.
802.3bt
(default) Fully conforms to the IEEE 802.3at/bt standard.
Legacy
The legacy mode provides power to those PD devices which do
not fully follow the IEEE 802.3af/at/bt standard. It also supports
capacitance tag PD (Cisco's own standard PD).