Acme Furniture AC00382 User manual





ASSEMBLY INSTRUCTION FOR ACME FURNITURE
Thank you for purchasing the quality product. Be sure to check all packing material carefully for small parts which
may have come loose inside the carton during shipment. Separate, identify and count all parts and metal hardware.
Compare with all parts are present. If any part(s) are missing or damaged, please contact your local furniture dealer.
For efficient and speedy service, please indicate the model number and code letter of part(s) needed.
***Do not fully tighten screws until fully assembled.***




Because our products may be challenging for beginners, we deeply understand that you
may encounter some difficulties. To avoid discouragement, we have provided some useful
tips, as follows.
Enough Open
Space -
Ensure that there is
enough space for
movement during
assembly.
Prevent
Scratching -
When assembling
furniture, use
cardboard, blankets or
a carpet areas to
prevent scratches.
Question -
If there is any problem
with the assembly
process, you can call
us.
?
More than two
people -
Always have at least
two people to help
transport and
assemble the product
to avoid potential
injury and/or damage.



Every cam bolt must have a cam lock connector to hold the parts together.
Insert the cam lock pin
into the hole of joint
panel.

The cam lock nut
opening side (or arrow)
aligned with the cam
lock pin.

Slowly rotate the cam
lock clockwise until it
stops rotating.

90
When assembling, the hardware parts and
the wooden board must be kept vertical,
and the tools must be in full contact with
the hardware groove.

Do not use excessive
force to advoid over-
fastening, or even
exceed the entire
board.
Caution:
Caution:
When assembling the cam lock, do not use an
electric screwdriver to avoid damage to the
board or hardware due to excessive force.



The holes of the slide rail are in the same direction as the following page.

Inner rail with narrower width:
fixed on the side panel of the
product.
Front
Back
1 2 3
1 2 3
1 2 3
180
The wider outer rail is placed
in the groove of the drawer.
Caution: The second hole
shown here is the hole
position fixed on the slide rail
when installing the drawer.
Inserting wood dowels is likely to be tight, so wood dowels
may not easily touch the bottom and damage the side panels
during installation. It is recommended to slight hit the wooden
pins with a hammer to eliminate the gap between the wood
dowel and board.
Gap

It is recommended to use white glue to increase the safety of
the produst. If you are worried about assembly errors, you can
temporarily not add it, and then add it after confirming.



 
A
 
B
 
C
 
D
 
E
 
F
 
G
 
H
 
I
 
J
 
K
 
L
 
M
 
N
 
R
 
P
 
Q

 
Some number parts listed on the instruction sheet may not be in parts bag as they may already be assembled.
Carefully check parts and packing materials prior to ordering replacements.
Attention

 

 
  

 

 

  

 
  #
  
  




 






F
Front


Front


G
2)Tighten the screws in the second hole in the front and the rear end of the inner rail.
1)Front side of slide rail needs to match front shape of the board.


Front




F

G
E
BC
D




A

I
H

J

B
E
F

C
D
G
Insert in as arrow
direction to specify




P
B
H
I
J
F

P
C
H
I
J
G
P
H







A
BC
FG
R
E

E
B
C
D






L
N
M



K


L


K

M



K
L
Q
M




ASSEMBLY IS COMPLETED.
Make sure the product is rested on a flat surface and does not feel loose or wobbly. If it does, double
check that the bolts/screws are secured and properly tightened.


R
R
Secure two screws from the inside of
the drawer using a Phillips screwdriver
to tighten them to the outer slides.

Extend the two outer slides of the
runners so that they could align with
the sides of the drawer. Make sure the
pre-drilled holes from the drawer align
with the screw holes of the outer slides.


K
K