Acon R930 P-TTL User manual

User Manual
flash trigger for
R930
ISM 2400MHz
Note: this manual is for firmware 3.0, would be
updated with the firmware updated in the future.
Version 03
Date: June.2 2015
acon
Features & Functions:
P-ttl High Speed Sync mode -
1/8000s capable.
Second Curtain Sync mode
Wired and wireless shutter release
functions
Power adjust mode
2.4G ISM bandwith
firmware upgradable
signal strength indicated
SafetyWarning:
Note: Do not set the flash on the re
ceiver in a manner that the flash mi
ght slice out the of receiver hot shor
e adapter.
Do not used with High Voltage hot shoe
flash.
Battery:
4 AAA battery are required to
function this trigger. When Updating
Firmware, Only fresh Alkaline and
Zinc-carbon are well.
Parts:
○
1 . Top button
○
2 . Function LED
○
3 .Side button
○
4 . Power Switch
○
5 . 2.5mm Output Port
○
6 . Firmware Update Port
○
7 . Hot shoe(Transmitter only)
○
8 . Battery Compartment
○
9 . Locking Ring
○
10. Hot Shoe Adaptor
○
11. Front LED
Prepare Connection:
All equipment should be turn OFF when
making connections.
The powering up sequence is essential
for this trigger.
Recommendation is:
1) Transmitter
2) Receiver
3) Flash
4) Camera
Power Off sequence is reversed.
If needed, repower the SLR to make
new connection.
AUTO Mode:
In this mode . the triggers transfer
signal as they are. just as the flash set
directly on the camera.
To set this mode. press the side button
long. When the LED 4 blink. Then short
press the side button to switch between
Auto->Manual ->Remote->(undefined)
mode. When LED 4 is green, long press
the side key, to confirm using the auto
transfer mode.
After entering the set mode (led 4 blink),
the top button is used to switch between
several setting. but for firmware 3.0.
user only use the led 4. Please make
sure that led 4 blink but not LED 1,2,3.
Manual power mode:
In this mode . user can set the flash
power as he/she want it.
To set this mode. similarly as the above.

User Manual
flash trigger for
R930
ISM 2400MHz
Note: this manual is for firmware 3.0, would be
updated with the firmware updated in the future.
Version 03
Date: June.2 2015
acon
Features & Functions:
P-ttl High Speed Sync mode -
1/8000s capable.
Second Curtain Sync mode
Wired and wireless shutter release
functions
Power adjust mode
2.4G ISM bandwith
firmware upgradable
signal strength indicated
SafetyWarning:
Note: Do not set the flash on the re
ceiver in a manner that the flash mi
ght slice out the of receiver hot shor
e adapter.
Do not used with High Voltage hot shoe
flash.
Battery:
4 AAA battery are required to
function this trigger. When Updating
Firmware, Only freshAlkaline and
Zinc-carbon are well.
Parts:
○
1 . Top button
○
2 . Function LED
○
3 .Side button
○
4 . Power Switch
○
5 . 2.5mm Output Port
○
6 . Firmware Update Port
○
7 . Hot shoe(Transmitter only)
○
8 . Battery Compartment
○
9 . Locking Ring
○
10. Hot Shoe Adaptor
○
11. Front LED
Prepare Connection:
All equipment should be turn OFF when
making connections.
The powering up sequence is essential
for this trigger.
Recommendation is:
1) Transmitter
2) Receiver
3) Flash
4) Camera
Power Off sequence is reversed.
If needed, repower the SLR to make
new connection.
AUTO Mode:
In this mode . the triggers transfer
signal as they are. just as the flash set
directly on the camera.
To set this mode. press the side button
long. When the LED 4 blink. Then short
press the side button to switch between
Auto->Manual ->Remote->(undefined)
mode. When LED 4 is green, long press
the side key, to confirm using the auto
transfer mode.
After entering the set mode (led 4 blink),
the top button is used to switch between
several setting. but for firmware 3.0.
user only use the led 4. Please make
sure that led 4 blink but not LED 1,2,3.
Manual power mode:
In this mode . user can set the flash
power as he/she want it.
To set this mode. similarly as the above.

User Manual
flash trigger for
R930
ISM 2400MHz
Note: this manual is for firmware 3.0, would be
updated with the firmware updated in the future.
Version 03
Date: June.2 2015
acon
Features & Functions:
P-ttl High Speed Sync mode -
1/8000s capable.
Second Curtain Sync mode
Wired and wireless shutter release
functions
Power adjust mode
2.4G ISM bandwith
firmware upgradable
signal strength indicated
SafetyWarning:
Note: Do not set the flash on the re
ceiver in a manner that the flash mi
ght slice out the of receiver hot shor
e adapter.
Do not used with High Voltage hot shoe
flash.
Battery:
4 AAA battery are required to
function this trigger. When Updating
Firmware, Only freshAlkaline and
Zinc-carbon are well.
Parts:
○
1 . Top button
○
2 . Function LED
○
3 .Side button
○
4 . Power Switch
○
5 . 2.5mm Output Port
○
6 . Firmware Update Port
○
7 . Hot shoe(Transmitter only)
○
8 . Battery Compartment
○
9 . Locking Ring
○
10. Hot Shoe Adaptor
○
11. Front LED
Prepare Connection:
All equipment should be turn OFF when
making connections.
The powering up sequence is essential
for this trigger.
Recommendation is:
1) Transmitter
2) Receiver
3) Flash
4) Camera
Power Off sequence is reversed.
If needed, repower the SLR to make
new connection.
AUTO Mode:
In this mode . the triggers transfer
signal as they are. just as the flash set
directly on the camera.
To set this mode. press the side button
long. When the LED 4 blink. Then short
press the side button to switch between
Auto->Manual ->Remote->(undefined)
mode. When LED 4 is green, long press
the side key, to confirm using the auto
transfer mode.
After entering the set mode (led 4 blink),
the top button is used to switch between
several setting. but for firmware 3.0.
user only use the led 4. Please make
sure that led 4 blink but not LED 1,2,3.
Manual power mode:
In this mode . user can set the flash
power as he/she want it.
To set this mode. similarly as the above.

User Manual
flash trigger for
R930
ISM 2400MHz
Note: this manual is for firmware 3.0, would be
updated with the firmware updated in the future.
Version 03
Date: June.2 2015
acon
Features & Functions:
P-ttl High Speed Sync mode -
1/8000s capable.
Second Curtain Sync mode
Wired and wireless shutter release
functions
Power adjust mode
2.4G ISM bandwith
firmware upgradable
signal strength indicated
SafetyWarning:
Note: Do not set the flash on the re
ceiver in a manner that the flash mi
ght slice out the of receiver hot shor
e adapter.
Do not used with High Voltage hot shoe
flash.
Battery:
4 AAA battery are required to
function this trigger. When Updating
Firmware, Only freshAlkaline and
Zinc-carbon are well.
Parts:
○
1 . Top button
○
2 . Function LED
○
3 .Side button
○
4 . Power Switch
○
5 . 2.5mm Output Port
○
6 . Firmware Update Port
○
7 . Hot shoe(Transmitter only)
○
8 . Battery Compartment
○
9 . Locking Ring
○
10. Hot Shoe Adaptor
○
11. Front LED
Prepare Connection:
All equipment should be turn OFF when
making connections.
The powering up sequence is essential
for this trigger.
Recommendation is:
1) Transmitter
2) Receiver
3) Flash
4) Camera
Power Off sequence is reversed.
If needed, repower the SLR to make
new connection.
AUTO Mode:
In this mode . the triggers transfer
signal as they are. just as the flash set
directly on the camera.
To set this mode. press the side button
long. When the LED 4 blink. Then short
press the side button to switch between
Auto->Manual ->Remote->(undefined)
mode. When LED 4 is green, long press
the side key, to confirm using the auto
transfer mode.
After entering the set mode (led 4 blink),
the top button is used to switch between
several setting. but for firmware 3.0.
user only use the led 4. Please make
sure that led 4 blink but not LED 1,2,3.
Manual power mode:
In this mode . user can set the flash
power as he/she want it.
To set this mode. similarly as the above.

but when the LED 4 is red. long press
the side key.
Then use the top key to increase flash
power and side key(short press) to
decrease flash power.
Wireless remote mode:
Similarly as the above. but when the led
4 red and green both ON. long press the
side key to confirm mode selection.
In this mode , use the transmitter in your
hand as controller. Plug the 2.5mm
cable to connect the camera 2.5mm slot
and the 'camera' slot of the receiver.
TTL pass through:
Although not recommended. due to
mounting up the flash and transmitter on
a SLR made more unstable structure.
User can do this for some cases. before
using this. make sure the power of the
transmitter is off.
Update Firmware:
To update firmware Please read the
manual of the acon firmware update
utility , which you can down load from
acon official site.
Wire control mode:
Power off the trigger. Plug the 2.5mm
cable to connect the camera 2.5 m
m slot and the 'camera' slot of the re
ceiver(or the transmitter)
Electronic Contact:
For AF360II AF540II, which use metal
hot shoe. be careful that the flash fix
firmly on the receiver. user may need to
turn the flash tighter to make the
connect touch OK if it is loose or poor
contact. Try turn the flash on the
receiver hot shoe adapter around a little.
When using with Pentax SLR, The lo
cking ring of the transmitter need not
tight too firmly, this might cause con
nection pins untouched.
Trouble shooting:
No action
1) power switch turn to ON?
1) battery isn't out of power?
2) Battery pole is OK?
3) Transmitter front LED not blink?
check the hot shoe connection. loose
the Locking ring..
4) Repower SLR to remake connection.
Misfire
1) Poor hot shoe connection?
2) Normal communication OK?
3) LED 1 on transmitter blink too many
(signal too weak due to obstacle or
interference) ?
Exposure mistake
1) Mode set to manual power mode?
2) Setting made on the SLR root?
Warranty:
This product is warranted against
defects in materials or workmanship for
one (1) year from the date of original
purchase. It does not cover damages or
wear resulting from accident, misuse,
abuse, commercial use, or unauthorized
adjustment and/or repair.
Should this product require service (or
replacement at our option)
while under warranty, do not return to
retailer. Please pack the item
carefully and return it prepaid, along with
a store receipt showing date of purchase
and a note explaining reason for return
to:
acon international Corp, Ltd
21H, LuShan Building
Luohu District
Shenzhen, China 518000
www.acon-photo.com
There are no express warranties except
as listed above. This warranty
gives you specific legal rights, and you
may have other rights which
vary from state to state.
IMPORTANT: We suggest that
user check everything OK by turn
the lens focus to see the lamp inside
the flash moving. also see the
distance showed on the flash
screen.

but when the LED 4 is red. long press
the side key.
Then use the top key to increase flash
power and side key(short press) to
decrease flash power.
Wireless remote mode:
Similarly as the above. but when the led
4 red and green both ON. long press the
side key to confirm mode selection.
In this mode , use the transmitter in your
hand as controller. Plug the 2.5mm
cable to connect the camera 2.5mm slot
and the 'camera' slot of the receiver.
TTL pass through:
Although not recommended. due to
mounting up the flash and transmitter on
a SLR made more unstable structure.
User can do this for some cases. before
using this. make sure the power of the
transmitter is off.
Update Firmware:
To update firmware Please read the
manual of the acon firmware update
utility , which you can down load from
acon official site.
Wire control mode:
Power off the trigger. Plug the 2.5mm
cable to connect the camera 2.5 m
m slot and the 'camera' slot of the re
ceiver(or the transmitter)
Electronic Contact:
For AF360II AF540II, which use metal
hot shoe. be careful that the flash fix
firmly on the receiver. user may need to
turn the flash tighter to make the
connect touch OK if it is loose or poor
contact. Try turn the flash on the
receiver hot shoe adapter around a little.
When using with Pentax SLR, The lo
cking ring of the transmitter need not
tight too firmly, this might cause con
nection pins untouched.
Trouble shooting:
No action
1) power switch turn to ON?
1) battery isn't out of power?
2) Battery pole is OK?
3) Transmitter front LED not blink?
check the hot shoe connection. loose
the Locking ring..
4) Repower SLR to remake connection.
Misfire
1) Poor hot shoe connection?
2) Normal communication OK?
3) LED 1 on transmitter blink too many
(signal too weak due to obstacle or
interference) ?
Exposure mistake
1) Mode set to manual power mode?
2) Setting made on the SLR root?
Warranty:
This product is warranted against
defects in materials or workmanship for
one (1) year from the date of original
purchase. It does not cover damages or
wear resulting from accident, misuse,
abuse, commercial use, or unauthorized
adjustment and/or repair.
Should this product require service (or
replacement at our option)
while under warranty, do not return to
retailer. Please pack the item
carefully and return it prepaid, along with
a store receipt showing date of purchase
and a note explaining reason for return
to:
acon international Corp, Ltd
21H, LuShan Building
Luohu District
Shenzhen, China 518000
www.acon-photo.com
There are no express warranties except
as listed above. This warranty
gives you specific legal rights, and you
may have other rights which
vary from state to state.
IMPORTANT: We suggest that
user check everything OK by turn
the lens focus to see the lamp inside
the flash moving. also see the
distance showed on the flash
screen.

but when the LED 4 is red. long press
the side key.
Then use the top key to increase flash
power and side key(short press) to
decrease flash power.
Wireless remote mode:
Similarly as the above. but when the led
4 red and green both ON. long press the
side key to confirm mode selection.
In this mode , use the transmitter in your
hand as controller. Plug the 2.5mm
cable to connect the camera 2.5mm slot
and the 'camera' slot of the receiver.
TTL pass through:
Although not recommended. due to
mounting up the flash and transmitter on
a SLR made more unstable structure.
User can do this for some cases. before
using this. make sure the power of the
transmitter is off.
Update Firmware:
To update firmware Please read the
manual of the acon firmware update
utility , which you can down load from
acon official site.
Wire control mode:
Power off the trigger. Plug the 2.5mm
cable to connect the camera 2.5 m
m slot and the 'camera' slot of the re
ceiver(or the transmitter)
Electronic Contact:
For AF360II AF540II, which use metal
hot shoe. be careful that the flash fix
firmly on the receiver. user may need to
turn the flash tighter to make the
connect touch OK if it is loose or poor
contact. Try turn the flash on the
receiver hot shoe adapter around a little.
When using with Pentax SLR, The lo
cking ring of the transmitter need not
tight too firmly, this might cause con
nection pins untouched.
Trouble shooting:
No action
1) power switch turn to ON?
1) battery isn't out of power?
2) Battery pole is OK?
3) Transmitter front LED not blink?
check the hot shoe connection. loose
the Locking ring..
4) Repower SLR to remake connection.
Misfire
1) Poor hot shoe connection?
2) Normal communication OK?
3) LED 1 on transmitter blink too many
(signal too weak due to obstacle or
interference) ?
Exposure mistake
1) Mode set to manual power mode?
2) Setting made on the SLR root?
Warranty:
This product is warranted against
defects in materials or workmanship for
one (1) year from the date of original
purchase. It does not cover damages or
wear resulting from accident, misuse,
abuse, commercial use, or unauthorized
adjustment and/or repair.
Should this product require service (or
replacement at our option)
while under warranty, do not return to
retailer. Please pack the item
carefully and return it prepaid, along with
a store receipt showing date of purchase
and a note explaining reason for return
to:
acon international Corp, Ltd
21H, LuShan Building
Luohu District
Shenzhen, China 518000
www.acon-photo.com
There are no express warranties except
as listed above. This warranty
gives you specific legal rights, and you
may have other rights which
vary from state to state.
IMPORTANT: We suggest that
user check everything OK by turn
the lens focus to see the lamp inside
the flash moving. also see the
distance showed on the flash
screen.

but when the LED 4 is red. long press
the side key.
Then use the top key to increase flash
power and side key(short press) to
decrease flash power.
Wireless remote mode:
Similarly as the above. but when the led
4 red and green both ON. long press the
side key to confirm mode selection.
In this mode , use the transmitter in your
hand as controller. Plug the 2.5mm
cable to connect the camera 2.5mm slot
and the 'camera' slot of the receiver.
TTL pass through:
Although not recommended. due to
mounting up the flash and transmitter on
a SLR made more unstable structure.
User can do this for some cases. before
using this. make sure the power of the
transmitter is off.
Update Firmware:
To update firmware Please read the
manual of the acon firmware update
utility , which you can down load from
acon official site.
Wire control mode:
Power off the trigger. Plug the 2.5mm
cable to connect the camera 2.5 m
m slot and the 'camera' slot of the re
ceiver(or the transmitter)
Electronic Contact:
For AF360II AF540II, which use metal
hot shoe. be careful that the flash fix
firmly on the receiver. user may need to
turn the flash tighter to make the
connect touch OK if it is loose or poor
contact. Try turn the flash on the
receiver hot shoe adapter around a little.
When using with Pentax SLR, The lo
cking ring of the transmitter need not
tight too firmly, this might cause con
nection pins untouched.
Trouble shooting:
No action
1) power switch turn to ON?
1) battery isn't out of power?
2) Battery pole is OK?
3) Transmitter front LED not blink?
check the hot shoe connection. loose
the Locking ring..
4) Repower SLR to remake connection.
Misfire
1) Poor hot shoe connection?
2) Normal communication OK?
3) LED 1 on transmitter blink too many
(signal too weak due to obstacle or
interference) ?
Exposure mistake
1) Mode set to manual power mode?
2) Setting made on the SLR root?
Warranty:
This product is warranted against
defects in materials or workmanship for
one (1) year from the date of original
purchase. It does not cover damages or
wear resulting from accident, misuse,
abuse, commercial use, or unauthorized
adjustment and/or repair.
Should this product require service (or
replacement at our option)
while under warranty, do not return to
retailer. Please pack the item
carefully and return it prepaid, along with
a store receipt showing date of purchase
and a note explaining reason for return
to:
acon international Corp, Ltd
21H, LuShan Building
Luohu District
Shenzhen, China 518000
www.acon-photo.com
There are no express warranties except
as listed above. This warranty
gives you specific legal rights, and you
may have other rights which
vary from state to state.
IMPORTANT: We suggest that
user check everything OK by turn
the lens focus to see the lamp inside
the flash moving. also see the
distance showed on the flash
screen.