ACR Electronics NAUTICAST SAR AIS - User manual

User Manual
P/N 2660
SAR AUTOMATIC IDENTIFICATION SYSTEM
ACR Electronics, Inc.
5757 Ravenswood Road
Fort Lauderdale, Fl 33312
[phone]
Fax [phone]
www.acrelectronics.com
Email: [email protected]
Y1-03-0207

=
User Manual I Y1-03-0207 Rev. A
Please read this first!
Warning:
Although ACR strives for accuracy in all its publications; this material may contain errors or
omissions, and is subject to change without prior notice. ACR shall not be made liable for any
specific, indirect, incidental or consequential damages as a result of its use. ACR components may
only be used in safety of life devices or systems, with the express written approval of ACR, as the
failure of such components could cause the failure of the ACR device or system. If these fail, it is
reasonable to assume that the safety of the user or other persons may be endangered.

User Manual II Y1-03-0207 Rev. A
1STARTING THE NAUTICAST..................................................................................................................................................................4
1.1 Initial Set Up of the NAUTICAST for operation...........................................................................................................................4
1.2 Entering the MMSI and IMO Numbers........................................................................................................................................5
1.3 Entering Ship Settings ................................................................................................................................................................7
1.4 Entering Voyage Related Data ...................................................................................................................................................8
1.5 Service and User Passwords....................................................................................................................................................10
2NAUTICAST USER INTERFACE............................................................................................................................................................13
2.1 NAUTICAST Keyboard .............................................................................................................................................................14
2.2 Explanation of the “Cursor Cross” ............................................................................................................................................14
2.3 Explanation of the Num-Locked and [NUM] Functions.............................................................................................................14
2.4 Explanation of the Soft Keys.....................................................................................................................................................15
2.5 Safety Keys...............................................................................................................................................................................15
3NAUTICAST SCREENS .......................................................................................................................................................................16
3.1 Navigation Screen ........................................................................................................................................................................16
3.1.1 Short Header....................................................................................................................................................................18
3.1.2 Other Vessel Details ........................................................................................................................................................19
3.2 Menu Structure .........................................................................................................................................................................21
3.3 Main Menu ................................................................................................................................................................................22
3.4 Sub-Menus Overview ...............................................................................................................................................................23
3.4.1 Messages.........................................................................................................................................................................23
3.4.2 AIS Status........................................................................................................................................................................23
3.4.3 Voyage Settings – (User Password Protected) ...............................................................................................................24
3.4.4 Ship Settings – (User Password Protected) ....................................................................................................................24
3.4.5 Configuration – (User Password Protected) ....................................................................................................................25
3.4.6 Service Configuration – (Service Password Protected)...................................................................................................25
3.4.7 Display Settings ...............................................................................................................................................................26
3.4.8 Graphical Display Settings...............................................................................................................................................26
3.5 Sub-Menus Detailed .................................................................................................................................................................27
3.5.1 Messages.........................................................................................................................................................................27
3.5.2 AIS Status........................................................................................................................................................................41
3.5.3 Voyage Settings (User Password Protected) ..................................................................................................................46
3.5.4 Ship Settings (User Password Protected) .......................................................................................................................49
3.5.5 Transponder Configuration (User Password Protected)..................................................................................................53
3.5.6 Service Configuration (Service Password Protected)......................................................................................................65
3.5.7 Display Settings ...............................................................................................................................................................71
3.6 Graphical User Interface (GUI) .................................................................................................................................................72
3.6.1 Switching between the Views ..........................................................................................................................................72
3.6.2 The Radar View ...............................................................................................................................................................74
3.6.3 Message and Alarm Handling..........................................................................................................................................82
3.6.4 Configuration of the Graphical Display ............................................................................................................................84
4SAFETY FUNCTIONS.............................................................................................................................................................................94
4.1 MOB Person over Board................................................................................................................................................................94
4.2 Activating the SRM Safety Related Message Button ..........................................................................................................................96
5TROUBLESHOOTING ...........................................................................................................................................................................101
5.1 Reading and understanding Alarms:..............................................................................................................................................101
5.2 Alarm Codes..............................................................................................................................................................................102
5.3 Text Messages..........................................................................................................................................................................103
5.4 Restarting the NAUTICAST..........................................................................................................................................................103
6CONTACT AND SUPPORT INFORMATION .............................................................................................................................................. 104
7APPENDIX..........................................................................................................................................................................................105
7.1 Explanation of commonly used Abbreviations ........................................................................................................................105
7.2 Certificates
NAUTICAST Transponder
User Manual
Index Page Number

User Manual III Y1-03-0207 Rev. A
History of Changes
Date Version Rev. Status Comments Responsible
2006-09-18 1.0 A Released Release New J. Wuenschel

User Manual 4 Y1-03-0207 Rev. A
1 Starting the NAUTICAST
1.1 Initial Set Up of the NAUTICAST for operation
ATTENTION: IMO REGULATIONS MANADATE THAT YOU ENTER THIS INFORMATION.
After installing the antennas and hardware the following User, Voyage related and Ship Settings
data needs to be entered. Upon Start-up (Applying power) enter the following information.
a) Enter MMSI Number - See paragraph 1.2 on entering information.
During the initial boot or after “factory settings” the user is asked to enter a valid MMSI
number. As long as this is not done, the system does not transmit. This appears as Alarm-ID
56 with the text “AIS: ENTER MMSI NUMBER”.
b) Enter IMO Number - See paragraph 1.2 on Entering information.
c) Ship Settings Data - After initial entry of the Ship Settings Data any changes in the
information below should be edited accordingly. See Paragraph 1.3 on entering information.
•Enter Call Sign
•Enter Ships Name
•Enter Length of Ship
•Enter Beam of Ship
•Enter Internal GPS antenna Position
•Enter External GPS Antenna Position (If applicable).
•Enter Ship Type
d) Voyage related Data – After initial entry of the Voyage related Data any changes in the
information below should be edited accordingly.
See paragraph 1.4 above on entering information.
•Enter Cargo Type
•Enter Draught
•Enter Destination
•Enter ETA
•Enter Navigation Status.
e) Password – Service and User passwords see section 1.5
LAT: N/A SOG: N/A 00/00/00
LON: N/A COG: N/A 24:60:60
IntN/A: STOP ! 7A 1T
++++++++++++++++++++++++++++++++++++++++
Time 24:60 00/00
[!] ALARM ID:56
AIS: ENTER MMSI NUMBER
Please press OK to enter MMSI number!
Tx temporary suppressed
++++++++++++++++++++++++++++++++++++++++

User Manual 5 Y1-03-0207 Rev. A
1.2 Entering the MMSI and IMO Numbers
Select from the Main Menu “Service Configuration” Number 6. Menu is SERVICE password
protected with default password “NAUT”. Enter Service Password and use the up and down arrows
on keypad to select “Change MMSI / IMO” than press M5 “Select” or “by pressing number 3 on the
keypad.
Input your MMSI and IMO number and press Save to store data. Unit will reboot itself after pressing
Save. Continue to 4.2 after reboot.
Service Configuration Menu Example:
Note: MMSI and IMO Data input are limited to 9 characters.
N 1o21' E 0
o
1
4' |1>0.01|2>1.30|3>1.80nm
|----------------------------------
| 6. Service Configuration
-----| |
| +- 1. Change Service Password
View | +- 2. User Password Settings
| +- 3. Change MMSI / IMO
-----| +- 4. Restore Factory Settings
|
Msg. |
|
-----|
|
Displ|
----------------------------------------
NUM| Select->| | |<-Back
N 1o19' E 0o13' |1>0.01|2>1.30|3>1.8
0
nm
|----------------------------------
| Menu
-----| |
| +- 1. Messages
View | +- 2. AIS Status
| +- 3. Voyage Settings
-----| +- 4. Ship Settings
| +- 5. Transponder Configuration
Msg. | +- 6. Service Configuration
| +- 7. Display Settings
-----|
|
Displ|
----------------------------------------
NUM| Select->| | |<-Back

User Manual 6 Y1-03-0207 Rev. A
N 1o21' E 0o14' |1> N/A|2>0.00|3>0.10nm
********** Change MMSI / IMO ***********
MMSI :1193046
IMO No.:303174162
----------------------------------------
NUM| Save | | | Back

User Manual 7 Y1-03-0207 Rev. A
1.3 Entering Ship Settings
Select from the Main Menu “Ship Settings” Menu is USER password protected with default password
“NAUT”. Enter Password and use the up and down arrows to edit Ship Settings then press Enter or
the numeric reference on the keypad to select and edit.
Save after editing.
Main Menu Example:
Select Ship Settings and press M5 [Enter]. Enter User Password and Continue.
Ship Settings Menu Example:
Select and enter Call Sign.
Select and enter Ship Name.
Select and enter Length of Ship.
Select and enter Beam of Ship.
Select and enter Internal and External GPS antenna positions.
Select and enter a default ShipType with the [Left] & [Right] arrows.
N 1o23' E 0o16' |1>0.01|2>1.30|3>1.80nm
|----------------------------------
| Menu
-----| |
| +- 1. Messages
View | +- 2. AIS Status
| +- 3. Voyage Settings
-----| +- 4. Ship Settings
| +- 5. Transponder Configuration
Msg. | +- 6. Service Configuration
| +- 7. Display Settings
-----|
|
Displ|
----------------------------------------
NUM| Select->| | |<-Back
N 1o19' E 0o12' |1>0.01|2>1.30|3>1.80nm
************ Ship Settings *************
/\ +
CallSign:D11233 / \|
ShipName:ANDREA DORIA | |
Length :220m | A
Beam :43m | x--+
RefPtExt:A200 B20 C10 D33m | | B
RefPtInt:A190 B30 C20 D23m +-C-+D-+
ShipType: Pilot vessel
----------------------------------------
| Save | | | Back

User Manual 8 Y1-03-0207 Rev. A
Setting the Internal and External GPS Antenna Position.
Note: It is critical for the proper orientation of your ship to other AIS users to enter this data
accurately.
Example: Length of ship = 220m and Beam = 43m.
GPS ANTENNA location on ship (is x in above Menu example) is located 200 meters from bow (A)
and 33 Meters from Starboard side (D).
Note: You can only enter Dimension A and D. B and C are automatically calculated.
You would enter A200D33 (without spaces, no decimals and no commas).
Then Press Save.
The line then should look like the example above for External Reference point.
RefPointExt = A200 B20 C10 D33m (Position of the external GPS antenna)
A = the distance from bow (front) to the antenna.
B= the distance from the antenna to the stern (rear)
C = the distance from the port (left) side to the antenna
D = the distance from the antenna to the starboard (right) side
Enter RefPtInt (location of the internal GPS antenna) in the same way.
Save the new settings by pressing [Save].
Press [Back] return to the Main Menu Screen without saving any changes.
1.4 Entering Voyage Related Data
Select from the Main Menu “Voyage Settings” Menu is USER password protected with default
password “NAUT”. Enter Password and use the up and down arrows to edit Voyage Related data
then press Enter or the numeric reference on the keypad to select and edit.
Save after editing.
Main Menu Example:
N 1o20' E 0o13' |1> N/A|2>0.00|3>0.10nm
|----------------------------------
| Menu
-----| |
| +- 1. Messages
View | +- 2. AIS Status
| +- 3. Voyage Settings
-----| +- 4. Ship Settings
| +- 5. Transponder Configuration
Msg. | +- 6. Service Configuration
| +- 7. Display Settings
-----|
|
Displ|
----------------------------------------
NUM|Select->| | |<-Back

User Manual 9 Y1-03-0207 Rev. A
Password inquiry Example: The password query field appears. Input password and press M5 [Enter].
Scroll to the Voyage Setting Fields with up and down arrows and input your vessel data.
Select a default Cargo Type, Draught, POB (Persons on board), Destination, ETA and Navigation
Status Setting using the [Left] & [Right] arrow keys.
Save the new settings by pressing [Save], and return to the Main Menu Screen by pressing [Exit].
Press [Back] to return to the Main Menu without saving any changes.
Voyage Related Menu Example:
N 1o31' E 0o24' |1>0.01|2>1.30|3>1.80nm
----------------------------------------
++++++++++++++++++++++++++++++++++++++++
User password protected!
Please enter user password:
++++++++++++++++++++++++++++++++++++++++
----------------------------------------
| Enter | | | Exit
N 1o18' E 0o12' |1>0.01|2>1.30|3>1.80nm
*********** Voyage Settings ************
Cargo :<N/A or harmless>
Draught :24.8m
PoB :1
Dest. :CASABLANCA
ETA :10/13 12:31
NavStat.:Engaged in fishing
----------------------------------------
| Save | | | Back

User Manual 10 Y1-03-0207 Rev. A
1.5 Service and User Passwords
The Transponder system is equipped with two levels of Password Protection, User and Service
Password.
1) The User Password, which is the lower security level, allows access to all menus except Menu 6:
Service Configuration which is protected by the Service Password.
2) The Service Password is required in order to enter the Service Configuration Menu. This is a
higher security level that can not be accessed with the User Password and therefore ensures that
the Service Configuration is protected, and limited to authorized service personnel.
The master of the vessel has to ensure that only authorized persons are allowed to make changes to
the Service Configuration and ensures that the newly reset password is stored very carefully, as it
can not be reset from the default “NAUT” a second time.
WARNING: a master key is not available and the unit would have to be returned to a service center
to correct for a lost Service password.
The User Password can be reset in the service configuration menu by entering the Service
Configuration menu and creating a new password.
Changing the Service Password
Select “Service Configuration” from the Main Menu with the cursor button [Up] & [Down] or press
Number 6 on the keyboard.
The password query field appears. Input default Service Password “NAUT” and press M5 [Enter].
Select Submenu 1 “Change Service Password” with cursor button [Up] & [Down] by pressing Nr. 1
on the keyboard.
N 1
o
24' E 0
o
17' |1>0.10|2>1.30|3>1.80nm
----------------------------------------
++++++++++++++++++++++++++++++++++++++++
Service password protected!
Please enter service password:
++++++++++++++++++++++++++++++++++++++++
----------------------------------------
| Enter | | | Exit

User Manual 11 Y1-03-0207 Rev. A
Service Menu Example:
Service Password Menu Example:
Enter the new Password: Then push Enter (M5).
Repeat the new Password: Then Push Enter (M5).
A minimum of 4, a maximum of 8 characters are allowed. Should the new password include
numbers, use the shift key to generate them.
Press Save to store the change.
Changing the User Password
Select Submenu 2 “User Password Settings” with cursor button [Up] & [Down] or by pressing Nr. 2
on the keyboard.
N 1
o
25' E 0
o
18' |1>0.10|2>1.30|3>1.80nm
******* Change Service Password ********
Enter new password :
Repeat new password:
{Length: 4..8 characters}
----------------------------------------
| Save | | | Back
N 1o21' E 0o14' |1>0.01|2>1.30|3>1.80nm
|----------------------------------
| 6. Service Configuration
-----| |
| +- 1. Change Service Password
View | +- 2. User Password Settings
| +- 3. Change MMSI / IMO
-----| +- 4. Restore Factory Settings
|
Msg. |
|
-----|
|
Displ|
----------------------------------------
NUM| Select->| | |<-Back

User Manual 12 Y1-03-0207 Rev. A
Select Submenu 1 “Change User Password” with cursor button [Up] & [Down] or by pressing Nr. 1
on the keyboard.
Enter the new Password:
Repeat the new Password:
A minimum of 4, a maximum of 8 characters are allowed. Should the new password include
numbers, use the shift key to generate them.
Press Save to store the changes.
N 1
o
25' E 0
o
18' |1>0.10|2>1.30|3>1.80nm
******* Change User Password ***********
Enter new password :
Repeat new password:
{Length: 4..8 characters}
----------------------------------------
| Save | | | Back
N 1o21' E 0o14' |1>0.01|2>1.30|3>1.80nm
|----------------------------------
| 6-2. User Password Settings
-----| |
| +- 1. Change User Password
View | +- 2. Change Password Protection
|
-----|
|
Msg. |
|
-----|
|
Displ|
----------------------------------------
NUM| Select->| | |<-Back
N 1o21' E 0o14' |1>
0
.01|2>1.30|3>1.80nm
|----------------------------------
| 6. Service Configuration
-----| |
| +- 1. Change Service Password
View | +- 2. User Password Settings
| +- 3. Change MMSI / IMO
-----| +- 4. Restore Factory Settings
|
Msg. |
|
-----|
|
Displ|
----------------------------------------
NUM| Select->| | |<-Back

User Manual 13 Y1-03-0207 Rev. A
2 NAUTICAST User Interface
Navigation Screen
Header (max. 3 lines)
________________
_
Navigation Screen or
MENU
S
tructure
(Content 13 lines)
Soft Keys [M1] – [M8]
Display Safety Keys
Curser
Cross
Enter Key
Keyboard
.
o

User Manual 14 Y1-03-0207 Rev. A
2.1 NAUTICAST Keyboard
The NAUTICAST is fitted with a full alphanumeric keyboard, with the following functions:
By pressing any key on the keyboard the letters are addressed.
Number symbols and special characters are addressed by holding down the
shift [×] key and simultaneously pressing the chosen key.
The characters ($; %; &; /; (; ); <; o; \ ; [; ]; ) can be reached by holding down the Function [Fn] key
and pressing the chosen key.
2.2 Explanation of the “Cursor Cross”
The Cursor Cross allows navigation within the current
screen [Up] [Down] [Left] [Right].
In addition to the actually displayed [Enter] button, the
center of the cursor cross always has the Enter functionality.
2.3 Explanation of the Num-Locked and [NUM] Functions
The NUM-Locked function is enabled after pressing the Function [Fn] Key and the Shift [×] Key.
It is possible to disable the Num-Lock Function by pressing the Shift [×] Key.
Tip: The NAUTICAST automatically changes the keys “Q” through to “P” to numerical input when the
current application requires numbers, rather than letters to be input. This feature is enabled when
[NUM] appears on the bottom left hand side of the screen.

User Manual 15 Y1-03-0207 Rev. A
2.4 Explanation of the Soft Keys
The Soft Keys are divided into vertical static keys [M1-M4] and horizontal dynamic keys [M5-M8],
which differ in function according to the current application.
Soft Key Definition
[M1]
filter option on AIS targets in graphical view
•FA (hides received Class A targets)
•FB (hides received Class B targets)
[M2] Display Modes
This Soft Key allows toggling between the different Display Modes.
[M3]: Safety Message
This Soft Key allows direct Message Writing. Either broadcast or addressed messages
can be sent in this mode. Pending alarms could be accessed by this Soft Key
[M4]:
Display Settings - Brightness and Contrast Regulator
This Soft Key allows the Display Settings to be changed between Daytime,
and Nighttime Modes.
[Menu]: Go to Main Menu or return to the Navigation View Screen.
[M5] – [M8]: These Soft Keys are described in individual screens
2.5 Safety Keys
The NAUTICAST is fitted with Safety Keys, which allow the user to automatically send urgent
messages without the necessity of navigating the Menus.
[MOB]
The MOB Button sends out precise position of an MOB incident to Addressed
Vessels, therefore allowing the message to be sent to a vessel closest to
accident location.
[SRM] The SRM Button sends out emergency Broadcast Safety Related Messages to
all ships in the Vessel Listing.
Note:
For detailed description of the Safety Functions see Chapter 4.

User Manual 16 Y1-03-0207 Rev. A
3 NAUTICAST Screens
The advanced version of the NAUTICAST offers three display modes:
Navigation Screen - Standard screen, automatically visible
Menu Structure - Visible after pressing the [Menu] Soft Key
Graphical User Interface - The Graphical User Interface is visible after pressing the [M2] Soft
Key (new mode)
3.1 Navigation Screen
This screen provides the user with Navigation Data from their own vessel and lists all other vessels
within receiving range. This screen automatically appears after a period of 60 seconds of user
inactivity on the Transponder.
Lines 1 – 3 of the Navigation Screen represent your own vessels data (display Latitude and
Longitude, Speed Over Ground, Course Over Ground, Heading, Date and the UTC).
After line 4, all data refers to other vessels within receiving range.
Dynamic Keys: Navigation Screen
[M5] Select desired vessel
for Vessel Details
[Up] /
[Down] Scroll Vessel Listing Pages
[Enter] Select desired vessel for
Vessel Details [Left] / [Right] Scroll Vessel Listing Pages
LAT:N 1
°
27.845'ExtSOG:34.6kn 05/26/06
LON:E 0°21.289'ExtCOG:173.0° 10:52:26
IntGPS: 3D A/ ExtHDT:222° Reg6 !
3
A 2T
001/021..ShipName....RNG.BRG..SOG..COG..
DOREEN [Cl-A] N/A 120 22.2 301.5
FINE EAGLE [Cl-A] 0.00 N/A 13.1 359.9
SYLVAEPSILON [Cl-A] 0.10 23 32.1 203.2
ESSOTOKYO [Cl-A] 0.43 99 10.0 120.3
KATHARGO [Cl-B] 0.59 342 21.2 50.0
SANEI [Cl-A] 0.80 272 32.1 270.1
KATOO [Cl-A] 1.00 321 21.2 200.8
ID=002319999_[Base] 1.34 277 0.0 0.0
MINILOG [Cl-A] 1.96 201 21.7 102.2
ALIBRAHIMYA [Cl-A] 2.66 340 22.1 30.3
EWALD M [Cl-A] 2.75 121 N/A N/A
ID=231919191 [SAR ] 3.36 66 24.1 2.9>

User Manual 17 Y1-03-0207 Rev. A
Own Vessel Data
LAT:N 1°27.845'ExtSOG:34.6kn 05/26/06
LON:E 0°21.289'IntCOG:173.0° 10:52:26
LAT: Latitude
LON: Longitude
Date: The actual UTC - date (MM.DD.YY) and time (hh.mm.ss) are displayed on the top
right hand corner of this view.
IntGPS: 3D A/ ExtHDT:222° Reg6
IntGPS Indicates normal or differential mode of GPS position.
2D or 3D: Indicates the precision of the GPS result.
Indicates the used position source:
intGPS. = internal GNSS receiver
extGPS = external GNSS receiver (sensors)
A/B: (A or B) Indicates the last transmitting channel in use.
ExtHDT True Heading
Reg: Indicates the actual region of own vessel’s position. If no region number is displayed,
then the vessel is traveling on high sea and is outside a predefined region.
Message (SRM) Indication
LAT:N 1o27.845'ExtSOG:34.6kn *3S
Queued safety related messages, e.g. *3S are displayed in the date field (instead of the date) – in
the above example 3 Safety Related (3S) Messages are queued, and await viewing and handling
(acknowledgement or reply) in the Message Inbox History.
Alarm (ALR) and Text (TXT) Indication
IntGPS: 3D /B Reg6 ! 3A 2T
Queued alarms or messages, e.g. ! 3A 2T are displayed in the 3rd line – in the above example
3 (3A) Alarms and 2 (2T) Text Messages are in queue, and await viewing and handling
(acknowledgement and reaction).

User Manual 18 Y1-03-0207 Rev. A
Other Vessel Data
001/021..SHIPNAME....RNG.BRG..SOG..COG..
001/021 (E.g: Vessel 01 of 021) current or selected Vessel/ Total number of Vessels (max.
256 Vessels)
ShipName:
Name of the Ship and AIS – Type:
Cl-A: SOLAS Class-A Ship
Cl-B: Leisure Craft
Base: Base station
SAR : Search and Rescue Aircraft
RNG
Vessel Range
Note: The vessel closest to own ship, or where position data is unknown (N/A), is
listed first.
BRG Vessel True Bearing
SOG Speed Over Ground
COG Course Over Ground
A maximum of 12 vessels are displayed on the screen. If more than 12 vessels are currently being
received, the symbol [>] on the right bottom appears, indicating that there are further vessels to be
seen in the Vessel Listing. By pressing the [Right] key, it is possible to scroll to the next page for
further Vessel Listing, by pressing the [Left], the user scrolls back to the previous page.
Further details on any individual vessel can be obtained by scrolling down and selecting the desired
vessel by pressing [Enter]. A full explanation of the Vessel Details is given in the following section.
3.1.1 Short Header
A constant overview of the most important AIS navigation details, including own position and
distance of the three closest vessels is always displayed the first line. This information appears in
every Submenu and is called the “Short Header”.
N 1o21 E 0o14' |1>0.10|2>1.30|3>1.80nm
Own Vessel Position: N 1o21' E 0o14'
1> Closest vessel situated 0.10 nm away
2> Second closest vessel situated 1.30nm away
3> Third closest vessel situated 1.80nm away

User Manual 19 Y1-03-0207 Rev. A
3.1.2 Other Vessel Details
This screen shows the Dynamic, Voyage and Vessel Related Data, which is currently being
transmitted by a previously selected vessel.
Current Time and Selected Vessel Number in Vessel Listing:
Time 2:07 ---------------- POS: 0001/0021
Time:
The period of time which has elapsed since the last update is shown in minutes and seconds.
The update rate differs according to the respective vessels speed.
POS:
Indicates the number of the selected vessel (e.g. vessel 02 of 21) from the Vessel Listing and the
total number of vessels being received.
Position of the selected vessel:
LAT :S 74-50'23" LON :W 9-34'19"
Heading and Rotation of the selected vessel:
Heading :77oROT :-0.2o/min l
IMO-Number and MMSI of the selected vessel:
IMO No. : 90733283 MMSI: 5004
Name and CallSign of the selected vessel:
ShipName:DOREEN CS:DORET6W
Vessel Type
Passenger ship
N 1
o
21' E 0
o
14'
|
1>0,10|2>1.30|3>1.80nm
Time 2:07 ------------------ POS:001/021
LAT : S 74-50'23 LON : W 9-34'19
Heading :77oROT :-0.2o/min l
IMO No. :90733283 MMSI:5004
ShipName:DOREEN CS:DORET6W
ShipType:Passenger ship
Length :310m Beam:73m
RefPoint:A190 B120 C10 D>=63m
Cargo :N/A or harmless
Draught :3.3m
Dest. :HAWAI
ETA :10/15 12:31
NavStat.:Moored
EPFDType:GPS
PosAcc :High<10m DTE :Available