Action Sports Equipment Pty Ltd. S000462 User manual

ACTIONSPORTSEQUIPMENTPTYLIMITED Page:1
Action Sports Equipment Pty Ltd.
72 Silverwater Rd, Silverwater, NSW, Australia, 2128
Parts & Service Enquiries: 1800 465 070 (Australia); 09 488 4750 (New Zealand)
WOODEN 3 RIDE GYMSET
MODEL#S000462
OWNER`S MANUALASSEMBLY INSTRUCTION
THIS PRODUCT PICTURE IS FOR REFERENCE ONLY
!
WARNING
YOU MUST THOROUGHLY READ AND UNDERSTAND
INSTRUCTIONS IN THIS MANUAL BEFORE ASSEMBLING
AND USE THIS SWING SET
SAVE THIS MANUAL FOR FUTURE REFERENCE.
THE UNIT DESIGNED FOR A MAXIMUM OF FOUR (4) CHILDREN BETWEEN THE AGES OF
THREE (3) AND EIGHT (8) YEARS OF AGE
DO NOT ALLOW YOUNG CHILDREN TO USE UNLESS SUPERVISED BY AN ADULT.

ACTIONSPORTSEQUIPMENTPTYLIMITED Page:2
Dear Customer,
Thank you for purchasing this product, we hope that you will enjoy it and have fun with friends and
family.
Please note this is a natural product and as such should be checked for any rough surfaces before
use, if required these should be lightly sanded in order to prevent injury.
It will take a while to assemble it.
Please take it as an exercise in assembling this product, be patient and enjoy this process with a
partner.
Thanks and Best Regards,
Action Sports

ACTIONSPORTSEQUIPMENTPTYLIMITED Page:3
WARNING!
Please read this instruction manual before you start to assemble or use this swing set. You must follow
all of the safety instructions while using this equipment. Be absolutely sure that the surface on which
this swing set is set up on is properly surfaced with fine sand, wood chips or double shredded bark
mulch .Do not use this swing set on hard packed soil ,concrete or any other kind of hard surface. Read
all cautionary statements on pages 2 and 3 before using this equipment.
Warnings
YOUR CHILD`S SAFETY DEPENDS ON YOU!
¾Suitable for children aged 3-8 years.
¾Not suitable for children under the age of 36 months because of small part(s) – choking hazard.
¾WARNING: This unit is designed to be used safely by up to 4 children with a maximum weight of
45.kgs each, simultaneously, not to exceed a combined weight of 180 kgs.
¾Adult supervision is required at all times whilst the product is in use. Never leave children
unattended during play.
¾Only one child per seat at any one time.
¾For outdoor use only.
¾Check all nuts, bolts and fittings for tightness and tighten if required.
¾Check all coverings for bolts and sharp edges and replace when required.
¾Oil all metallic moving parts.
¾Check swing seats, ropes and other means of attachments for evidence of deterioration. Replace
when required in accordance with the manufacture’s instructions.
¾Please take note: As an extra precaution, check this toy regularly for signs of wear and damage.
¾Place the product on a soft level surface at least 2 meters from any structures or obstructions such
as a fence, garage, house, overhanging branches, laundry line or electrical wires.
¾Leave all fittings finger-tight until assembly is complete, for ease of construction. Then tighten
firmly.
¾For safety reasons, this swing MUST be locateded on the level ground.
¾Ground anchors are supplied and we recommend these are concreted into the ground
¾Anchors shall be placed level with or under the ground in order to reduce the risk of tripping.
¾DO NOT let children use this equipment until it has been properly assembled and anchored. Place
equipment on level ground not less than 2M from any structures or obstacles such as fences,
overhanging branches, laundry or electrical line, garages, sheds or houses.
¾This item is not for adults or children weighing more than 45kg.
¾DO NOT install the product on concrete, asphalt or hard surfaces.
¾DO NOT allow children to stand on the swing seats.
¾DO NOT allow children to get off the swings while they are still moving.
¾DO NOT twist swing ropes or wrap them over the top bar.
¾DO NOT allow loose, hooded or baggy clothes to be worn since children can get trapped and may
be unable to free themselves.
¾DO NOT allow children to climb on this equipment.
¾DO NOT allow children to wander into the play area when the equipment is in use.
¾Swings must not exceed an angle of 60 degrees from the ground.

ACTIONSPORTSEQUIPMENTPTYLIMITED Page:4
¾Failure to assemble and maintain this item as per these instructions may cause injury to the user.
¾DO NOT orientates the swing directly towards the sun.
¾Packaging materials are not toys. Please remove all packaging and packing tags / wires before
giving this toy to your child.
¾Adult assembly required.
¾For use under adult supervision.
¾Maintenance to be carried out under the direct supervision of a responsible adult. Please refer to
the maintenance schedule in this manual for proper upkeep of the unit
¾For family domestic use only.
¾Once assembly is complete, carefully check the equipment before use. If you find any problems,
do not allow children to use the equipment until it is fit for use. For missing components or
damaged part replacement, please contact the national service centre.
¾Do not let children use the equipment until it has been fully assembled.
¾Remove all assembly tools once fully assembled.
¾This product accommodates no more than 1 child on each play component at one time.
¾Do not attach items to the equipment that are not specifically designed for use with this product.
Such as, but not limited to, cables, skipping ropes and chains as they may cause strangulation
hazards.
¾Not suitable for hiring or commercial use.
¾Never use the equipment in any manner other than intended.
¾Never attempt to relocate item without fully disassembling. Shifting of the item in assembled
form will lead to undue stress and potential breaking of frame and components of the product.
¾Do not use the product when temperatures are expected to drop below 0.C. Remove all plastic
parts and place indoors after each use.
¾Shredded bark mulch, wood chips, fine sand or fine gravel are considered to be acceptable
shock-absorbing surfaces when installed and maintained at a sufficient depth under and around
playground equipment. However each material is only effective when properly maintained.
Materials should be checked periodically and replenished to maintain correct depth as determined
necessary for your equipment. Otherwise serious injuries may occur from a fall.
¾Maintenance Instruction:
¾Check all nuts and bolts twice monthly during the usage season and tighten as required(But not so
tight that you crack the wood). We recommend that you check the swing beam and hardware
every two weeks due to wood expansion and contraction. It is particularly important that this
procedure be followed at the beginning of each season.
¾Check all coverings for bolts and sharp edges twice monthly during usage season to be certain
they are in place. Replace when necessary. It is especially important to do this at the beginning of
each new season.
¾All outdoor wooden products require routine inspection and regular maintenance. After installation,
a follow –up inspection should take place after one week and twice a month thereafter for the
remaining life of your play products. Maintenance should be performed at any time it is deemed
necessary. As a general rule, major maintenance(wood refinishing) should be performed at twelve
month intervals from the date of installation. Inspect and perform maintenance based on the
following checklist.
¾Major wooden parts: Inspect for splintering and structure defects. If necessary, lightly sand and
refinish with an exterior water repellent stain.
¾Hardware : Inspect for tightness. Be certain that hardware is firmly against, but not crushing the
wood. Over-tightening hardware crushes wood fibers and splits wooden components and could
result in the bolt threads extending beyond the wood and presenting a severe safety hazard. If
splintering has occurred from over tightening, large washers can be purchased at your local

ACTIONSPORTSEQUIPMENTPTYLIMITED Page:5
hardware store and installed under the bolt head. Be sure to reuse or replace your lock washers. If
over-tightening has caused the bolts threads to protrude beyond the wood surface, replace the
bolt with a shorter one that will not protrude. These bolts are standard items and can be purchased
at your local hardware store.
¾Ongoing Wood treatment: This product is supplied in a natural stain finish
and has not been chemically treated, The timber used in this product has not
undergone any hazardous treatment and required constant maintenance to
ensure the longevity and optimal performance and appearance of the product.
To maintain product appearance and lifespan the following is suggested:
¾Depending on your climate or location, the wood can start to change in colour
appearance, sings of fading or change in colour are a clear sign that new
protectant application is required.
¾At regular intervals, the application of a penetrating oil based sealer stain to
all wooden components is essential. Please consult your local hardware or
home improvement store for recommendation of an appropriate product.
Ensure the product does not contain hazardous chemicals once dry that can
pose a potential health risk to children.
¾The wood originally has a natural wood stain colour, if desired, the stain
colour can be changed
¾Please retain these instructions for future reference.

ACTIONSPORTSEQUIPMENTPTYLIMITED Page:6
AT LEAST 2 ADULT ASSEMBLY！！！
BEFORE YOU BEGIN ASSEMBLY!!!
WARNING
Take a complete inventory of components using the parts list.
Sort and lay out the wood pieces. Label each piece of wood for easy reference. For easy
identification during the assembly process, write the board’s letter on masking tape and adhere to
each piece of the wood. Some wooden components may twist or warp in the carton after
packaging. Usually, these parts straighten out when assembled. You may also see some
cracking of the grain. .
Sort all hardware according to size. Do not worry if extra hardware is included.
Find a safe play location.
You MUST install the 3 Ride Swing Set on level ground. Uneven ground must be leveled prior to
installation. The manufacturer cannot assume responsibility for any failure from incorrect
installation. Installing on sloping ground will put stress on all the joints, which will cause the set to
become loose and unstable
The safe play area must be free of all structures, landscaping, trees and branches, rocks, wires
and other obstacles to safe play. Children can be seriously injured running or swinging into these
obstacles
Remove any rocks or any jagged or sharp object that could endanger your children’s’ safety.
Remove all tripping hazards from the safe play area. Tripping hazards include but are not limited
to: roots, stumps, rocks, landscaping, sprinkler heads, railroad ties, plumbing, and electrical
connections.

ACTIONSPORTSEQUIPMENTPTYLIMITED Page:7
COMPLETE EXPLODED DIAGRAM

ACTIONSPORTSEQUIPMENTPTYLIMITED Page:8
PART LIST

ACTIONSPORTSEQUIPMENTPTYLIMITED Page:9
HARDWARE LIST
MNO
PQ
Z5
0.6cmX5cm
2 PCS
0.6cmX3.7cm
4 PCS 0.6cmX 5.7cm
2 PCS
10PCS 48PCS
4 PCS
8 PCS
4 PCS
4 PCS
4MM
T 1 PCS
11-13
U 1PCS
Z8
2PCS 30PCS 8 PCS 10 PCS
RSZ6
0.8cmX17.8cm
0.8cmX9.2cm
12 PCS
0.8cmX8.9cm
K
JLZ7
0.6cm
0.8cm 0.8cm
8PCS
1.7cm 0.9cm
0.8cmX6.4cm
Z0
2 PCS
0.6cmX8.9cm
0.7cmX7.6cm
0.8cm
Z
2 PCS
0.8cmX2.2cm
Z9
Q1
4 PCS
0.7cmX5.1cm
4 PCS
N1
2 PCS
1cmX9.2cm
2 PCS
J1
1cm
4PCS
R3
12-14
U1 1PCS I
S1
2 PCS
1.3cm 2.2cm
64PCS
R2
2.2cm

ACTIONSPORTSEQUIPMENTPTYLIMITED Page:10
Y 2PCS
G5 2PCS
G3 2PCS
G7 2PCS
Z4 2 PCS
G1 1PCS G2 1PCS
G6 2PCS
G4 2PCS
F 2PCS
H 4PCS
R1
4 PCS

ACTIONSPORTSEQUIPMENTPTYLIMITED Page:11
STEP 1
1.1. ATTACH THE LEGS (D, D1) ON PILLAR (B), UISNG FLAT WASHERS (R2), SPRING WASHERS (S)
SCREWS (O) AND NUTS (J).
1.2. ATTACH THE LEGS (D, D1) ON THE CROSS BAR (A), USING FLAT WASHERS (R2), SPRING
WASHERS (S), SCREWS (N) AND NUTS (L).
1.3. ATTACH PILLAR (B) ON THE GROSS BAR (A), USING FLAT WASHERS (R), SPRING
WASHERS (S) AND SCREWS (Q),

ACTIONSPORTSEQUIPMENTPTYLIMITED Page:12
STEP 2
2. ATTACH THE TRIANGLE METAL SHEET (H) ON THE PILLAR (B), USING FLAT WASHERS (R2), SPRING
WASHERS(S), SCREWS (P) AND NUTS (J).

ACTIONSPORTSEQUIPMENTPTYLIMITED Page:13
STEP 3
3. ATTACH THE ANOTHER TRIANGLE METAL SHEET (H) ON THE ANOTHER PILLAR (B), USING FLAT
WASHERS (R2), SPRING WASHERS (S), SCREWS (P) AND NUTS (J).

ACTIONSPORTSEQUIPMENTPTYLIMITED Page:14
STEP 4
.
4.1. ATTACH THE LEGS (D, D1) ON PILLAR (B), UISNG FLAT WASHERS (R2), SPRING WASHERS (S)，
SCREWS(O)ANDNUTS(J).
4.2. ATTACH. THE LEGS (D, D1) ON THE CROSS BAR (A), USING FLAT WASHERS (R2), SPRING
WASHERS (S), SCREWS (N) AND NUTS (L).
4.3. ATTACH PILLAR (B) ON THE GROSS BAR (A), USING FLAT WASHERS (R), SPRING
WASHERS (S) AND SCREWS (Q),

ACTIONSPORTSEQUIPMENTPTYLIMITED Page:15
STEP 5
5. ATTACH THE TRIANGLE METAL SHEET (H) ON THE PILLAR (B), USING FLAT WASHERS (R2), SPRING
WASHERS (S), SCREWS (P) AND NUTS (J).

ACTIONSPORTSEQUIPMENTPTYLIMITED Page:16
STEP 6
6. ATTACH THE ANOTHER TRIANGLE METAL SHEET (H) ON THE ANOTHER PILLAR (B), USING FLAT
WASHERS (R2), SPRING WASHERS (S), SCREWS (P)AND NUTS (J).

ACTIONSPORTSEQUIPMENTPTYLIMITED Page:17
STEP 7
7.1. ATTACH THE SWING BEAM (E) ON THE PILLAR (B), UISNG FLAT WASHERS (R2), SPRING
WASHERS (S), SCREWS (M) AND NUTS (J).
7.2. ATTACH THE SWING BEAM (E) ON THE TRIANGEL METAL SHEET (H), USING FLAT WASHERS (R2),
SPRIGN WASHERS (S), SCREWS (O) AND NUTS (J).

ACTIONSPORTSEQUIPMENTPTYLIMITED Page:18
STEP 8
8.1. ATTACH THE SWING BEAM (E) ON THE PILLAR (B), UISNG FLAT WASHERS (R2), SPRING WASHERS
(S), SCREWS (M) AND NUTS (J).
8.2. ATTACH THE SWING BEAM (E) ON THE TRIANGLE METAL SHEET (H), USING FLAT WASHERS (R2),
SPRIGN WASHERS (S), SCREWS (O) AND NUTS (J).

ACTIONSPORTSEQUIPMENTPTYLIMITED Page:19
STEP 9
9.1 INSERT SWING SEAT CHAIN ITON (F) ONTO THE “U” STYLE (I).
9.2 ATTACH “U” STYLE (I) ON SWING BEAM (E), USING NUTS (K), FLAT WASHERS (R2) AND NUTS (J).

ACTIONSPORTSEQUIPMENTPTYLIMITED Page:20
STEP 10
10. ATTACH THE METAL PANEL (G1) ON THE SWING BEAM (E), USING FLAT WASHERS (R3), SPRING
WASHERS (S1), SCREWS (N1) AND NUTS (J1).