Action Sports S000463 Maintenance manual

Action Sports Equipment Pty Ltd.
72 Silverwater Rd, Silverwater, NSW, Australia, 2128
Parts & Service Enquiries: 1800 465 070 (Australia); 09 477 6020 (New Zealand)
Or email: [e-mail] (Australia) or [email protected] (New Zealand)
Sales Enquiries: 1800 777 137 (Australia); 09 477 6020 (New Zealand)
Or visit our website: www.actionsports.com.au
4-Unit Swing Set with Mini Trampoline
Model: S000463
Assembly, Installation, Care, Maintenance and Use Instructions
IMPORTANT
Please read and retain this manual as it will assist with identification for parts and service.
Read these materials prior to assembling and using this swing set.
This Product is for Domestic Use Only.
- Warning -
- This swing set is for family domestic use only.
- This swing set is designed for use by children 3-9 years of age weighing no more than 34kgs.
- This swing set has a maximum weight limit of 204kgs.
- Children of all ages must be supervised by an adult at all times when using this swing set.
- Adult assembly of this swing set is required. Two adults are recommended for assembly.
© ACTION SPORTS EQUIPMENT PTY LTD – www.actionsports.com.au Page:1

- WARNING -
1) Read and understand enclosed safety information before assembly and use of the swing set.
2) Place the swing set on a level and soft surface before use.
3) Lateral clearance is essential. The swing set should be placed not less than 2m (6 feet 6 inches) from any
structure or obstruction ie. a fence, garage, house, shed, overhead branches, clothes line etc.
4) DO NOT install this swing over hard surfaces such as concrete, asphalt or any other hard surface.
5) It is recommended that this swing set be positioned over soft lawn or fine sand.
6) Anchor the swing set using the wiggling anchor pegs provided to prevent overturning or lifting. The anchors
should be placed level with or under the ground in order to reduce the tripping hazards.
7) Never place the swing set under or near powerlines.
8) Never place the swing set inside a garage or basement or under any structure.
9) Always position the swing where it can be seen from the house.
10) This swing set is designed to be used by one child per seat at one time.
11) Do not allow additional items to be attached to the swing set such as ropes, chains, cords, or other items not
designed for use.
12) Do not use the swing set when it is wet as it will become slippery and serious injury may result.
13) Do not wear apparel such as hats with chin straps, helmets, scarves, garments with pull strings and other items
of loose clothing while using this swing set as they can cause serious injury.
14) Do not walk close to, in front of or behind the swing set when in use. Walking between moving rides can
cause serious injury.
15) Do not jump from the swing set when they are in motion.
16) Do not stand on the seats when using the swing set.
17) Do not climb on the side braces or the top support of the swing set.
© ACTION SPORTS EQUIPMENT PTY LTD – www.actionsports.com.au Page:2

TABLE OF CONTENTS
TABLE OF CONTENTS.................................................................................................................3
PARTS LIST – MAIN FRAME.......................................................................................................4
PARTS LIST – SWING SEAT.........................................................................................................4
PARTS LIST – TOT SWING...........................................................................................................5
PARTS LIST – GLIDE RIDER .......................................................................................................5
PARTS LIST – MINI TRAMPOLINE ............................................................................................6
PARTS MATCH LISTS – 1:1 Actual Scale.....................................................................................7
ASSEMBLYAND INSTALLATION INSTRUCTION ................................................................11
SECTION 1- MAIN FRAME ASSEMBLY..................................................................................12
SECTION 2- MINI TRAMPOLINE ASSEMBLY........................................................................15
SECTION 3- SWING SEATASSEMBLY....................................................................................18
SECTION 4 – TOT SWING ASSEMBLY ....................................................................................19
SECTION 5 – GLIDE RIDER ASSEMBLY.................................................................................20
SECTION 6 – ANCHOR PEGS....................................................................................................21
MAINTENANCE INSTRUCTION...............................................................................................22
CAUTION......................................................................................................................................22
LIMITED WARRANTY…………………………………………………………………………23
© ACTION SPORTS EQUIPMENT PTY LTD – www.actionsports.com.au Page:3

PARTS LIST – MAIN FRAME
Parts # Parts Description Quantity
MF-1a Top Support Tube A
1
MF-1b Top Support Tube B 1
MF-1c Top Support Tube C 1
MF-2 Top Support Tube
Brace 2
MF-3
Leg Stay 1
MF-4 Upper Leg Tube 4
MF-5 Lower Leg Tube 2
MF-6 Leg Tube with Welded
Socket 2
MF-7 Anchor Peg 4
PARTS LIST – SWING SEAT
Parts # Parts Description Quantity
MS-1
Swing SeatAssembly 2
MS-2 Eyebolt Assembly
(built- in to MS-1) 4
X6
Oval Opening Cap
(built-in to MS-2) 4
X16
Plastic Lock (built-in to
MS-2) 4
© ACTION SPORTS EQUIPMENT PTY LTD – www.actionsports.com.au Page:4

PARTS LIST – TOT SWING
Parts # Parts Description Quantity
TS-1 Tot Swing Upper
Hanger Tube
2
TS-2 Tot Swing Lower
Handle Tube 2
TS-3 Tot Swing Armrest
Tube with foam and
cover
1
TS-4 Tot Swing Support
Tube with foam and
cover
1
TS-5 Seat and Back Plate
(seat plate with one
hole at the centre of
front panel)
2
TS-6 Eyebolt Assembly
(built-in to TS-1) 2
PARTS LIST – GLIDE RIDER
Parts # Parts Description Quantity
GR-1
Glide Rider Upper
Hanger Tube 2
GR-2 Glide Rider Lower
Hanger Tube 2
GR-3 Glide Rider Seat Tube 2
GR-4 Glide Rider Seat 2
GR-5 Glide Rider Foot Step 2
X3 Bracket 4
© ACTION SPORTS EQUIPMENT PTY LTD – www.actionsports.com.au Page:5

X6 Plastic Bearing 2
U3 T-Shaped Washer 4
PARTS LIST – MINI TRAMPOLINE
Parts # Parts Description Quantity
MT-1 Mat with 28 V-rings 1
MT-2 Net 1
MT-3 Springs 28
MT-4 Safety Pad 1
MT-5 Top rail tube 2
MT-6 Top rail tube 1
MT-7 Top rail tube 2
MT-8
Leg tubes 2
MT-9 Handle tube with foam 1
MT-10 Leg Foam 2
© ACTION SPORTS EQUIPMENT PTY LTD – www.actionsports.com.au Page:6

PARTS MATCH LISTS – 1:1 Actual Scale
© ACTION SPORTS EQUIPMENT PTY LTD – www.actionsports.com.au Page:7

© ACTION SPORTS EQUIPMENT PTY LTD – www.actionsports.com.au Page:8

© ACTION SPORTS EQUIPMENT PTY LTD – www.actionsports.com.au Page:9

© ACTION SPORTS EQUIPMENT PTY LTD – www.actionsports.com.au Page:10

Tools included in the Item
Wrench Allen Key
A socket set and adjustable spanner may also be used to further assist in swing assembly.
- IMPORTANT -
Use this parts list to make sure all parts are present before assembly. Do not attempt to
assemble the swing set if any parts are missing or damaged. Disassemble the Swing Set
immediately if any part is missing or any unsafe condition exists. Obtain a replacement
part to properly correct the hazard by calling 1800 465 070 (Australia) or 09 477 6020
(New Zealand). Do not allow use of the swing set until the hazard has been corrected.
ASSEMBLYAND INSTALLATION INSTRUCTION
Read this entire assembly section before beginning to assemble your swing set. Carefully follow each
step.
NOTE:At least 2 persons are recommended for the following assembly.
In order to avoid injuries and damage to property, it
is recommended that the Swing Set should be at
least 2 metres away from any buildings, fences and
so on. Also clear the ground of any sharp objects.
Use the Parts List to make sure all parts are present. Contact Customer Service at 1800 465 070
(Australia) or 09 477 6020 (New Zealand) if any parts are missing. Do not attempt to assemble the
swing set if any parts are missing.
© ACTION SPORTS EQUIPMENT PTY LTD – www.actionsports.com.au Page:11

SECTION 1- MAIN FRAME ASSEMBLY
Note: At least two people are required for the assembly of the swing set.
Caution: The swing set should be placed on a soft surface, such as a grassed lawn area is
recommended.
1.1 Lay out the top frame on a soft and level surface as Fig. 1.Align holes, connect the Top Support Tubes
(MF-1a,b,c) and the Top Support Tube Braces (MF-2), using Bolts, Washers & Nuts of A2 &A3. See
Fig.2
Figure 1
Figure 2
1.2 Slide the Lower Leg Tubes (MF-5) into the Upper Leg Tubes (MF-4), align holes. Put the Leg Stay (MF-3)
onto the leg tube. Align holes and fasten with Bolts, Washers & Nuts of A1. See Fig.3
Figure 3
© ACTION SPORTS EQUIPMENT PTY LTD – www.actionsports.com.au Page:12

1.3 Use Bolts, Washers & Nuts of A2 to secure the rest Upper Leg Tubes (MF-4) to the Lower Leg Tubes with
Welded Socket (MF-6). See Fig 4.
Slide the Leg Foam (T10) into the Leg Tube done in Fig.4 as shown in Fig.5.
Figure4 Figure5
1.4 Put the Net (MT-2) into the leg tubes done in the above step 1.3 as shown in Figure 6.
Figure 6
© ACTION SPORTS EQUIPMENT PTY LTD – www.actionsports.com.au Page:13

1.5 Connect the two Mini Trampoline Top Rails (MT-5) using Bolts, Washers & Nuts of T2. Plug such Mini
Trampoline Top Rails to the welded sockets of the Swing Set Leg Tube. See the Front View of Fig.7
When it is done correctly, it looks like the Side View of Fig. 7.
FRONT VIEW SIDE VIEW
Figure 7
1.6 Secure the completed Leg Tubes to the Top Support Tube Braces (MF-2) with Bolts, Washers & Nuts of A3.
Make sure the welded sockets on the netted leg tube are pointing outwards of the swing set. See Fig. 8
Figure 8
© ACTION SPORTS EQUIPMENT PTY LTD – www.actionsports.com.au Page:14

SECTION 2- MINI TRAMPOLINEASSEMBLY
2.1 Connect the other Mini Trampoline Top Rail Tubes (MT-6) and (MT-7) together with the Bolts,
Washers & Nuts of T4. Attach the whole top rail to the socket of MT-5. See Fig.9
Note: There are no bolts and nuts to lock the mini trampoline top rail to the sockets on the swing leg. When
the springs are installed in later steps, the springs will hold the top rail tightly.
Figure 9
2.2 Attach the Mini Trampoline Leg Tubes (MT-8) to the Top Rail Tubes (MT-7). Tighten the top holes
with Bolts, Washers & Nuts (T1) and then fasten the bottom holes with Bolts, Washers & Nuts of
T3. See Fig.10
Figure 10
© ACTION SPORTS EQUIPMENT PTY LTD – www.actionsports.com.au Page:15

2.3 Hook up the first set of Springs (MT-3) at four
corners as shown in Figure 11.
Figure 11
2.4 Continue putting the remaining Springs (MT-3) to
the mat. See Fig. 12
Figure 12
2.5 There are elastic strap with hooks at the
bottom of the Net (MT-2) which are used
to secure the bottom part of the net. Pull
the elastic straps to go over the top rail
and hook them to the Mat’s V-ring as
shown in Figure 13.
Secure the pre-sewn hook and loop tapes
at the bottom of net to the leg tubes and
the Mini Trampoline top rail tubes. See
Fig.13
Figure 13
© ACTION SPORTS EQUIPMENT PTY LTD – www.actionsports.com.au Page:16

2.6 Place the Safety Pad (MT-4) onto the frame. See Fig.14
Figure 14
2.7 Pull the pre-sewn elastic straps and hooks on the Safety
Pad (MT-4) to go around the Mini Trampoline Top
Rails and hook to V-rings. See Fig. 15
Figure 15
2.8 Put the Handle Tube (MT-9) into the Leg Tubes (MT-8). Make sure the locking pins are secured in
positions. See Figure 16.
Figure 16
© ACTION SPORTS EQUIPMENT PTY LTD – www.actionsports.com.au Page:17

SECTION 3- SWING SEATASSEMBLY
Attach the Swing Seat to the Main Frame as shown Figure 17.
Figure 17
WARNING!
DO NOT OVER TIGHTEN EYEBOLTS!
THIS CAN RESULT INASSEMBLY FAILURE!
© ACTION SPORTS EQUIPMENT PTY LTD – www.actionsports.com.au Page:18

SECTION 4 – TOT SWINGASSEMBLY
Connect the Tot Swing to the Main Frame as shown in Figure 18.
Figure 18
WARNING!
DO NOT OVER TIGHTEN EYEBOLTS!
THIS CAN RESULT INASSEMBLY FAILURE!
© ACTION SPORTS EQUIPMENT PTY LTD – www.actionsports.com.au Page:19

SECTION 5 – GLIDE RIDER ASSEMBLY
Attach the Glide Rider to the Main Frame as shown in Figure 19.
Bracket Assembly
Figure 19
© ACTION SPORTS EQUIPMENT PTY LTD – www.actionsports.com.au Page:20