Active Intent PLAY User manual

Trampoline should be assembled on the flat lawn.
ATTENTION! This trampoline is supplied with a safety net and must be installed.
This safety net is designed to significantly reduce the trampoline user from falling off.
This net is NOT designed for rebounding, climbing or hanging off.
Failure to install the safety net or misuse of the net will increase the risk of injury.
The safety net does not replace the need for supervision and to ensure that users of this
trampoline are informed of all warnings and safety instructions.

Tableof Contents
SAFETY INSTRUCTIONS 2
CARE AND MAINTENANCE 3
TRAMPOLINE S LIST 4
EXPLODED DIAGRAM
ASSE INSTRUCTIONS 6
5
ENCLOSURE PARTS LIST 8
SAFETY ENCLOSURE ASSEMB 9
When ordering replacement parts please have the information ready:
1. Owner's Manual
2. Model Number
3. Descript ion of
4. P Number
5. Date of Purchase
Customer service number: 0800 422 274
MON - FRI: 8AM - 5PM
SSUN:
9AM - 4PM
Marketed By: The Warehouse LTD
26 The Warehouse Way, Northcote, Auckland
Warning
Max Weight Limited: 150KG

Trampoline should be assembled on the flat lawn.
ATTENTION! This trampoline is supplied with a safety net and must be installed.
This safety net is designed to significantly reduce the trampoline user from falling off.
This net is NOT designed for rebounding, climbing or hanging off.
Failure to install the safety net or misuse of the net will increase the risk of injury.
The safety net does not replace the need for supervision and to ensure that users of this
trampoline are informed of all warnings and safety instructions.

TRAMPOLINE FRAME ASSEMBLY
Refer to Parts List for identification of parts.
WARNING: 2 adults in good physical condition are required for the following assembly. Wear proper shoes
and maintain balance to prevent a fall. Failure to follow all instructions and warnings exactly may
result in serious injury.
1. Lay out all trampoline parts in groups
(just like picture)
2. Begin by attaching two leg extensions
to assemble one “W” shape leg with
rail screws (part H).
3. Attach the top rail as picture. Continue until you form a large
circle. Joining the last link may
require two or more adults in
good physical condition. With a
second person holding the opposite
end, bring both sides of the circle
firmly together and make them
secured.
4.
6. Now the frame assembly is complete. 7. With stitching portion facing down, lay jumping
mat inside frame and attach a spring into one
of the triangle rings on the mat. Then attach spring
with ring to frame.
WARNING: Trampoline is under heavy tension,
more effort may be required to attach springs to
frame. Be careful not to pinch fingers or slip.
Serious injury may occur!

TRAMPOLINE MAT & COVER ASSEMBLY
DANGER: 2 adults may be required to complete placement of all springs as illustrated in STEP 13. Springs will
create high levels of tension when assembled. Please use extreme caution not to pinch your fingers.
Caution:please always keep the side
Repeat this step directly across from
where you attached first spring. Then
attach two more springs half distance
between the first two, directly across
from each other.
8.
10.
13. 14.
12.
9.
Springs under heavy tension may
require adjacent springs to be
attached every four or five holes,
making thesprings tension
averagely distributed.
11. Attach remaining springs until all
springs are placed on frame
securely.
Tie all black straps to top rail of
frame. Do not tie to springs.
Your trampoline is now ready for the
enclosure to be attached!
Lay blue frame cover on outer
edge so springs are covered-
just like a shower cap.
Use spring tool as shown.
with "this side up" up.
To disassemble repeat steps 1-14 in reverse.

ITEM NO.
A
C
D
E
F
G
H
I
14’
6 Legs
PARTS
Upper eye bolt set
B
6
1
12
6
6
6
6
1
6
Lower pan head bolt set
Wrench
Plastic cap on screw
Pole cap
Pole bottom
Upper pole
Lower pole
Safety enclosure net
Safety enclosure net(1)
G
H
I
Upper Pole
Wrench(1)
Pole cap
Pole bottom
Plastic cap on screw
Lower Pole
A
C
B
D
EF
Upper eye bolt set Lower pan head bolt set

SAFETY ENCLOSURE ASSEMBLY
WARNING: 2 adults in good physical condition are required for the following assembly. Wear
proper shoes and maintain balance to prevent a fall. Failure to follow all instructions and
warnings exactly may result in serious injury.
Slide upper pole onto lower pole.
Repeat with remaining poles.
1. 2. Place the safety enclosure net on trampoline
tidily as shown ready for next step.
After succeeding in the first pole, repeat to all poles.
4. After firmly clamping all the poles to the
trampoline legs, put the cup hat on each
of the upper poles tightly.
3. Note: Firmly fix the lower pole and the leg extension with Upper eye bolt set(A) and
Then fasten the bolt by wrenching on
Lower pan head bolt set (B). the nut.
Upper eye bolt set
Lower pan head bolt set
A
B
5. Fasten the net with the cup hat.

7. Make the rope go through the under part
of net and the V-rings slightly.
9. Congratulations, your trampolines
safety enclosure is now complete!
6. Repeat with remaining, until all the
cup hats are fastened to the net.
8. Ending at the entrance slide fastener
and hooks.Responsible adult supervisor,
must re-zip the slide fastener and re-hook
all the hooks securely before jumping
begins.