Acuity Brands Lithonia Lighting KVE User manual

Lithonia Lighting Outdoor
OneLithoniaWay, Conyers,GA30012
Phone: [phone] Fax: [phone]
www.lithonia.com
Part Number:RJ5210129RevB
RevisionDate:11/8/10
Installation Instructions
KVE
SAVETHESEINSTRUCTIONS
WARNING
To reduce the risk of death, injury or property damage from fire, electric shock, cuts,
abrasions, falling parts, and other hazards:
•Serviceofthe equipment must beperformedby qualified service personnel.
•Installationand maintenance mustbe performed by a personfamiliar with theconstruction and
operationof this productand any hazardsinvolved.Allapplicablecodes and ordinancesmust
befollowed.
•Readthis document beforeinstalling, servicing, or maintaining thisequipment or installinga
lamp.These instructions do not coverall installation, service, and maintenancesituations. If
your situation is not covered, or if you do not understand these instructions or additional
informationis required, contactLithoniaLighting or your local Lithonia LIghting Distributor.
•Readandfollow all warningsandinstructions provided by thelamp manufacturer.
WARNING
Before installing, servicing, or maintaining this equipment, follow these general precautions.
To reduce the risk of electrocution:
•Makesure the equipmentisproperly grounded.
•Alwaysde-energize the circuitand/or equipment beforeconnecting to, disconnecting
from,orservicing the equipment.
To reduce the risk of fire:
•Keep material away that can burn from hot lamp.
•Make sure lamps are correctly installed.
•Use supply conductors with a minimum installation temperature rating as specified on
equipment.
To reduce the risk of personal injury from cuts, abrasions, or falling parts:
•Wearglovesto prevent cutsorabrasions from sharp edgeswhenremoving from carton,
handlingandmaintaining this equipment.
•Donot use abrasive materials, glasscleaners orother solvents on reflector orlens.
Thesesubstances may damageequipment and causeparts to eventuallybreak and
fall.
•Do not install a damaged fixture.
CAUTION: Observelamp manufacturer’s recommendationsand restrictions on lampoperation,
including but not limited to ballast type, burning position, replacement and cycling. Use only lamps that
complywith applicableANSIstandards.
NOTICE: If lamp is marked it contains mercury. Follow disposal laws. See www.lamprecycle.org
Lithonia Lighting, a division of Acuity Brands Lighting, Inc., assumes no responsibility for claims arising out of
improper or careless installation or handling of this product.
IMPORTANTSAFETYINSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS!
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

Lithonia Lighting Outdoor
OneLithoniaWay, Conyers,GA30012
Phone: [phone] Fax: [phone]
www.lithonia.com
Part Number:RJ5210129RevB
RevisionDate:11/8/10
Installation Instructions
KVE
DELIVERY: Upon receipt of fixture and accessories (packed separately), thoroughly inspect for any freight damage. All
damage should be reported to the delivery carrier. Do not install damaged fixtures. Compare the catalog description listed
on the packing slip with the fixture label on the inside of the housing to be sure you have received the correct merchandise.
Tools required: 3/4" socket w/extension, Philips-head screw driver, 5/16" nut driver (bridge mount), 3/8" (power door)
Side Mounting the fixture:
1. Remove the top cap from pole, if in place. Insert the mounting plate inside pole or
tenon adaptor, aligning the three (3) mounting holes in plate with the three (3)
mounting holes provided on the pole. Slide the two threaded rods through the top
and bottom mounting holes in the pole and start to thread the rods into the
matching holes in the mounting plate (three turns are sufficient). Place one of the
gaskets over the threaded rods and against the pole.
2. To mount the arm, slide arm over threaded rod using the bolt guides inside the
arm. Place remaining gasket over the threaded rods and against the mounting arm.
Post top Mount
1. The KVE mounts to a 4, 4-1/2, 5, or 6"
diameter pole top determined by the option
ordered.
2. Remove the top plate of the wiring
compartment. Make
wire connections,
replace the top
plate.
3. Secure the fixture
by slipping into the
pole top and
tightening (1)
internal fitter
device.
Lamp Installation: Prior to installing the lamp in the fixture, verify that the lamp source and wattage corresponds with the fixture label.
1. Open the housing assembly as shown above.
2. Disengage secondary disconnect plug.
3. Remove the socket cap.
4. Screw the lamp securely into the socket, back it out one or two turns,
and tighten it securely again. This procedure properly seats the lamp in
the socket.
5. Align socket cap, twist to lock.
6. Reconnect secondary disconnect plug.
7. Replace fixture top. Tighten screws securely.
Multi-tap Ballast (TB) The multi-tap ballast will be prewired for 277V at the factory. This option offers multi voltage capability. First determine the
correct line voltage. Then select the corresponding fixture voltage lead, remove the crimped cap and connect to the supply voltage lead. The fixture
lead marked COM should be connected to the neutral supply lead for 120 or 277. For 208 or 240, connect the other incoming hot leg to the fixture lead
marked “COM”. Be sure to cap off all unused fixture leads individually.
TROUBLESHOOTING - If this fixture fails to operate properly, check to make sure: • The correct lamp is properly installed. •The fixture is wired
correctly. •The lamp is not faulty. • The fixture is grounded correctly. •The line voltage at the fixture is correct.
3. Loosen the two captive screws on top of the
housing and open the top cover. Lift the top cover
up and over the side, resting the top cover on the
wireform.
4. Position the housing at the end of the arm and feed
fixture wires through arm, pole backing plate, and
out pole top. Align the holes with the threaded rods
and insert the threaded rods into the fixture. Install
split lockwashers and hex nuts (furnished) on the
ends of the threaded rods that are inside the fixture
and tighten securely. Make sure fixture is mounted
straight and square with pole before raising pole.
5. Make wire connections observing polarity per
instructions below. Connect green ground wire from
the fixture to field ground wire.
Socket
Cap
Socket
Reflector Socket cap
Exploded view of KVE housing and top.