Acument Avdel TX2000 Avdelok User manual

TX2000®Avdelok®/Maxlok® Collar Cropper
Instructions for Collar Cropper Attachment
1Do not use collar cropper outside the design intent printed below.
2Do not use equipment or tools with this collar cropper other than that recommended and supplied by Avdel UK Limited.
3The tool and collar cropper must be maintained in a safe working condition at all times. The operator must follow the daily and weekly
service checks detailed in the TX2000®Instruction Manual.
4The tool and collar cropper shall at all times be operated in accordance with the relevant health and safety legislation. Any question
regarding the correct operation of the tool and operator safety should be directed to your local Avdel UK Limited company or authorized
representative.
5Do not operate a tool that is pointed towards any person(s).
6Do not operate the tool if it is not fitted with a complete collar cropper assembly.
7 FINGERS AND ALL BODY PARTS MUST REMAIN CLEAR OF THE COLLAR CROPPER WHEN OPERATING THE TOOL.
8When using the tool and collar cropper, the wearing of safety glasses is required both by the operator and others in the vicinity to protect
against ejection of debris. We recommend wearing gloves if there are sharp edges or corners on the application.
9Take care to avoid entanglement of loose clothes, ties, long hair, cleaning rags etc., in the moving parts of the tool and collar cropper.
10 When carrying the tool from place to place keep hands away from the trigger to avoid inadvertent start up.
11 Remove the battery when not in use, or when fitting or removing the collar cropper.
This technical datasheet must be read with particular attention to the safety rules listed in the TX2000®Instruction Manual
07900-00759 and to the following safety rules, by any person fitting or operating the collar cropper and TX2000®tool.
Safety Rules
The collar cropper attachment in combination with the TX2000®tool is designed for cutting and removing Avdelok®and Maxlok®collars from
fasteners from 4.8mm (3/16”) to 6.4mm (1/4”). The correct collar cropper kit must be selected for each fastener size and type as shown in
the table on this page.
IMPORTANT
The tool and collar cropper must be used in accordance with the safety rules and fitting instructions contained within this
datasheet. The cropping of other fastener sizes or materials not included in the table on this page could have a detrimental
impact on the working life of the tool and collar cropper and could invalidate the warranty.
Intent of Use

1* 07500-06800 Collar Cropper 3/16 Avdelok® / Maxlok®
1* 07500-06900 Collar Cropper 1/4 Avdelok®
1* 07500-05900 Collar Cropper 1/4 Maxlok®
2 07498-050001 Anvil Adaptor
3 07498-05002 Collet Adaptor
4 71600-20101 Stop Nut
ITEM 71600-20100 TX2000®3/16 COLLAR CROPPER KIT - AVDELOK®/ MAXLOK®
71600-20110 TX2000®1/4 COLLAR CROPPER KIT - AVDELOK®
71600-20120 TX2000®1/4 COLLAR CROPPER KIT - MAXLOK®
Kits include:
© A v d e l U K L i m i t e d 2 0 0 7
Refer to drawing 71600-02000(s) or TX2000®tool manual
07900-00759. Item numbers in bold refer to parts list in table
on this page.
To prepare base TX2000®tool to accept Collar Cropper
equipment
1 Unscrew Jaw Spreader Housing 71210-02101 and remove
Locknut 71600-02026.
2 Substitute Locknut with Stop Nut 4. Refit Jaw Spreader
Housing 71210-02101. Ensure Jaw Spreader Housing is
fully tightened onto the Piston before tightening against the
Stop Nut 4.
Fitting the Collar Cropper Assembly
1 Fit Collet Adaptor 3onto Jaw Spreader Housing.
2 Screw Anvil Adaptor 2over the Collet Adaptor 3into the
front of the tool.
3 Attach Cropper Assembly 1* by screwing the Cam Rod of
the Assembly onto the Collet Adaptor 3.
4 Complete attachment by screwing the Nose Retaining Nut of
the Collar Cropper 1* assembly onto the Anvil Adaptor 2.
* Kit includes the specified Collar Cropper Assembly
Collar Cropper Anvil Adaptor
Collet Adaptor Jaw Spreader
Housing
Stop Nut
12
34
(71210-02101)
Avdel UK Limited
Watchmead Industrial Estate, Welwyn Garden City, Herts, AL7 1LY United Kingdom
Tel: [phone] Facsimile: [phone]
www.avdel-global.com
I M P O R T A N T
The battery must be disconnected when fitting or removing any nose assembly unless specifically instructed otherwise.
Fitting Instructions
Collar Cro p p e r A s s e m b l y P a r ts List
Manual No. Issue Change Note No. Date
07900-00826
AA 02/236
AB 07/176