Adam Equipment AE 402 User manual

© 2016 Adam Equipment
Adam Equipment
AE RELAY ACCESSORY
P.N. 3106611295, Revision B, Ma 2016

© 2016 Adam Equipment

© 2016 Adam Equipment 1 3106611295RevB-Ma 16
CAUTION
The relay accessory is designed to allow the AE402
indicator to connect to user equipment. High voltage connections
can be made to the relay PCB.
WARNING! All electrical installation and maintenance
work should be carried out by qualified electricians only.
WARNING! Do not attempt any work with power applied.
Switch off the mains. It is good practice to check (with a voltage
indicating instrument) that the power is off before beginning work.
DANGEROUS VOLTAGES may be p esent. Only qualified
pe sonal should attempt the connection of the elay to use equipment
DANGEROUS VOLTAGES can cause physical inju y and/o
damage to the equipment

© 2016 Adam Equipment 2 3106611295RevB-Ma 16
INSTALLATION
The AE 402 indicato is supplied with d ive s to cont ol exte nal elays.
The d ive s could be used to cont ol a numbe of diffe ent elays
depending upon the use s need. The elay d ive s a e isolated outputs
equi ing the use of an exte nal powe supply fo the elays.
The Relay Accesso y is a p oduct to allow quick and convenient
connections to the AE402 fo cont ol of exte nal equipment o
indicato s.
Connections to the AE042 a e made at te minal st ip P1:
Within the AE402 the output to d ive exte nal elays is on the ci cuit
boa d inside the enclosu e. To gain access you must emove the 6
sc ews secu ing the f ont to the ea of the case. Pass the wi es fo the
elays th ough the g ommet on the ea panel. The wi es will connect
to the PCB using the te minal st ip P1. See the AE402 Use manual fo
mo e details.
Any of the 4 elays can be connected to any of the 4 outputs. The
+12Vdc f om the elays connects to the Common te minal.

© 2016 Adam Equipment 3 3106611295RevB-Ma 16
POWER SUPPLY
Powe fo the elays can come f om a use supplied sou ce. 2
Alte native powe input points a e p ovided depending upon the powe
the use has available.
Connecto VAC is used fo 15-25VDC o 12-20VAC, 50/60Hz. 500ma.
This input is not sensitive to pola ity, eithe te minal can be used.
If the use has 12VDC to 15VDC, 500ma available then connecto ma ked
12VDc can be used. Be ca eful with the pola ity, using +12 to 12V and
minus voltage to the GND te minal.
Only one powe input te minal should be used at one time
OPERATION
Du ing ope ation the elays will be active at the same time the
Low/OK/High LEDs on the f ont panel ope ate and the Ze o elay is
activated when the scale is at ze o point.
Note the scale must show a small weight befo e the LOW LED will
activate. See the AE402 Use Manual fo details of how to set the limits.
Use connections to the elays a e made using the te minal st ips
ma ked OUT1 to OUT4. The elay active fo each LED will depend on the
input connection, Input IN1 cont ols elay 1, OUT1 fo example. But IN1
could be connected to any of the 4 te minals in the AE 402.
CAUTION:
The voltage and cu ent limits of the elay outputs must be less than:
115/230VAC, 1amp o 24VDC. 1amp.
Highe cu ents may damage the ci cuit boa d.
The elays a e not specified fo highe voltages.

© 2016 Adam Equipment 4 3106611295RevB-Ma 16
WARRANTY STATEMENT
Adam Equipment offers Limited Warranty (Parts and Labour) for any components that fail due to defects in
materials or workmanship. Warranty starts from the date of delivery.
During the warranty period, should any repairs be necessary, the purchaser must inform its supplier or Adam
Equipment Company. The company or its authorised Technician reserves the right to repair or replace the
components at any of its workshops at no additional cost, depending on the severity of the problems. However,
any freight involved in sending the faulty units or parts to the Service Centre should be borne by the purchaser.
The warranty will cease to operate if the equipment is not returned in the original packaging and with correct
documentation for a claim to be processed. All claims are at the sole discretion of Adam Equipment.
This warranty does not cover equipment where defects or poor performance is due to misuse, accidental damage,
exposure to radioactive or corrosive materials, negligence, faulty installation, unauthorised modifications or
attempted repair, or failure to observe the requirements and recommendations as given in this User Manual.
This product may include a rechargeable battery that is designed to be removed and replaced by the user. Adam
Equipment warrants that it will provide a replacement battery if the battery manifests a defect in materials or
workmanship during the initial period of use of the product in which the battery is installed.
As with all batteries, the maximum capacity of any battery included in the product will decrease with time or use,
and battery cycle life will vary depending on product model, configuration, features, use, and power management
settings. A decrease in maximum battery capacity or battery cycle life is not a defect in materials or workmanship,
and is not covered by this Limited Warranty.
Repairs carried out under the warranty do not extend the warranty period. Components removed during warranty
repairs become company property.
The statutory rights of the purchaser are not affected by this warranty. The terms of this warranty is governed by
the UK law. For complete details on Warranty Information, see the terms and conditions of sale available on our
web-site.
FCC / IC CLASS A DIGITAL DEVICE EMC VERIFICATION STATEMENT
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules and Canadian ICES-003/NMB-003 regulation. These
limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the interference
at his own expense.

© 2016 Adam Equipment 5 3106611295RevB-Ma 16
EU Declaration of Conformity / Déclaration de conformité / Konformitätserklärung
Declaración de Conformidad / Dichiarazione di conformità
16
Year CE marking was first affi ed to declared product
AE 402 RELAY ACCESSORY
Adam Equipment Co. Ltd.
Maidstone Road, Kingston Tel: [phone]
Milton Keynes, MK10 0BD Fax: [phone]
United Kingdom Email: [e-mail]
www.adamequipment.com
We declare under our sole responsibility that the balance models listed below marked with “CE” are
in conformity with the directives and standards mentioned.
Nous déclarons sous notre seule responsabilité, que les types de balance cités ci-dessous munis de
la mention "CE" sont conformes aux directives et aux normes mentionnées ci-après.
Wir erklären in alleiniger Verantwortung, dass die untenstehenden Waagentypen
gekennzeichnet mit "CE" mit den genannten Richtlinien und Normen übereinstimmen.
Nosotros declaramos bajo responsabilidad exclusiva que los modelos de balanzas indicados a
continuación con el distintivo "CE" son conformes con las directivas y normas citadas.
Noi dichiariamo sotto nostra unica responsabilità che i tipi di bilance specificati di seguito
contrassegnati con la marcatura “CE” sono conformi alle direttive e norme citate.
Adam Equipment AE 402 RELAY ACCESSORY.
2014/30/EU EN61326-1:2013 – Part 1
2014/35/EU EN61010-1:2010 – Part 1:
2011/65/EC, RoHS 2 EN50581: 2012,
Signed for and on behalf of: Adam Equipment Company Ltd.
United Kingdom, 20 Feb 2016
Clive Jones, Quality & Product Manager.
WEEE 2012/19/EU
This device may not be disposed of in domestic waste. This also applies to countries outside the EU, per their
specific requirements.
Cet appareil ne peut être éliminé avec les déchets ménagers
Dieses Gerät nicht mit dem Hausmüll entsorgt.
Dispositivo no puede ser desechado junto con los residuos domésticos
Dispositivo non può essere smaltito nei rifiuti domestici.

© 2016 Adam Equipment
ADAM EQUIPMENT
is an ISO 9001:2008 ce tified global company with mo e than 40
yea s’ expe ience in the p oduction and sale of elect onic weighing equipment.
Adam p oducts a e p edominantly designed fo the Labo ato y, Educational, Health and
Fitness, Retail and Indust ial Segments. The p oduct ange can be desc ibed as follows:
-Analytical and P ecision Labo ato y Balances
-Compact and Po table Balances
-High Capacity Balances
-Moistu e analyse s / balances
-Mechanical Scales
-Counting Scales
-Digital Weighing/Check-weighing Scales
-High pe fo mance Platfo m Scales
-C ane scales
-Mechanical and Digital Elect onic Health and Fitness Scales
-Retail Scales fo P ice computing
Fo a complete listing of all Adam p oducts visit ou website at
www.adamequipment.com
Adam Equipment Co. Ltd.
Maidstone Road, Kingston
Milton Keynes
MK10 0BD
UK
Phone:[phone]
Fax: [phone]
e-mail: [e-mail]
Adam Equipment Inc.
1, Fox Hollow Rd.
06478
USA
Phone: [phone]
Fax: [phone]
e-mail: [e-mail]
AE Adam GmbH.
Instenkamp 4
D-24242 Felde
Ge many
Phone [phone]
Fax: [phone]
e-mail: [e-mail]
Adam Equipment S.A. (Pty) Ltd.
7 Megawatt Road,
Spa tan EXT 22
Kempton Pa k,
Johannesbu g,
Republic of South Af ica
Phone [phone]
Fax: [phone]
e-mail: [e-mail]
Adam Equipment (S.E. ASIA) PTY Ltd
2/71 Tacoma Ci cuit
CANNING VALE 6155
Pe th
Weste n Aust alia
Phone: [phone]
Fax [phone]
e-mail: [e-mail]
Adam Equipment (Wuhan) Co. Ltd.
A Building East Jianhua
P ivate Indust ial Pa k
Zhuanyang Avenue
Wuhan Economic & Technological
Development Zone
430056 Wuhan
P.R.China
Phone: + 86 (27) 59420391
Fax + 86 (27) 59420388
e-mail: [e-mail]
©Copyright by Adam Equipment Co. All rights reserved. No part of this publication may be reprinted or translated in any
form or by any means without the prior permission of Adam Equipment.
Adam Equipment reserves the right to make changes to the technology, features, specifications and design of the equipment without
notice.
All information contained within this publication is to the best of our knowledge timely, complete and accurate when issued.
However, we are not responsible for misinterpretations which may result from the reading of this material.
The latest version of this publication can be found on our Website.
www.adamequipment.com