Adcraft BWM-7/R-2 User manual

This manual contains importatant information regarding your Adcraft unit. Please read this
manual thoroughly prior to equipment set-up, operation and maintenance. Failure to comply with
regular maintenance guidelines outlined in this manual may void the warranty.
INSTRUCTION MANUAL
BWM-7/R
BWM-7/R-2
BELGIAN WAFFLE MAKERS

June 2017
WARNINGS
• Do not touch any hot surfaces
• Plug only into a 3-hole grounded electrical outlet of the appropriate voltage
• Do not immerse unit, cord or plug in liquid at any time
• Unplug cord from outlet when not in use and before cleaning
• Do not operate unattended
• Do not use this unit for anything other than intended use
• Do not use outdoors
• Always use on a rm, dry and level surface
• Do not use if unit has a damaged cord or plug, in the event the appliance malfunctions, or has been
damaged in any manner
• Keep children and animals away from unit
• Any incorrect installation, alterations, adjustments and/or improper maintenance can lead to property
loss and injury. All repairs should be done by authorized professionals only.
TO USE
1. Turn on power switch. Three beeps will sound indicating that the machine has power and the heating
process has been initiated.
2. After this the LED display will show a time in minutes and seconds. Before you set the time you must
set the heating temperature that you would like to cook your wafes at. In order to do this hold the
“SET” button and then press the “START/STOP” button. This will then display the temperature that
the unit is currently set to. Use the “+ and –“ buttons in order to change the displayed temperature to
the one desired and then press “SET” to nalize this parameter. The unit will then continue heating to
this set temperature and will continue to maintain this temperature for the remainder of the cooking
process and the whole time the unit’s power switch is turned on.
3. In order to begin the time feature press and hold the “START/STOP” button and use the “+ and –“
buttons in order to change the minutes and seconds displayed on the LED display. Once you have set
your desired time press the “START/STOP” button once to begin the time countdown. Once the time on
the display has reached “00:00” an alarm will sound indicating the timer has ran out of time.
NOTE: The timer feature has NO AFFECT on the heating process. It is just a timer for your convenience
to help you keep track of your cooking times. The unit will always maintain the set temperature you have
input as long the power switch is turned on, regardless if the timer has run out or not.

June 2017
MAKING WAFFLES
Turn the unit on and pre-heat for 15 minutes with the wafe grids closed. To make wafes follow
these instructions:
1. Spray or brush on releasing agent.
2. Lift the top lid, pour in the mix and close. Allow wafe batter to sit for 10 seconds.
3. Start timer by pressing the start/stop button.
4. Rotate grids 180°.
5. Cook until the timer beeps and press the start/stop button to stop the timer.
6. Rotate grids 180°.
7. Remove wafe. Do not use metal utensils on non-stick wafe irons.
8. To cook more wafes repeat steps 1 through 7.
CLEANING – NOTE: To maintain cleanliness and increase service life, this item should be cleaned
daily. Do not immerse the unit in water or any other liquid. If liquid enters the electrical compartment
it may cause a short circuit or electrical shock
1. Unplug the unit and let cool down.
2. Clean the wafe iron plates with a wet towel only.
3. Do not use a wire scrub brush or metal utensils on the wafe iron plates.

June 2017
Wiring Diagram for the Wafe Makers
10V
T
230V
LN/AC 115V/50~60Hz 1.2kW/10.5A
���������������
2 1
3
3
3
5
5
5
4
4
4
4
7
6
7
6
1*
2*
2*
1*
3*
4*
E
12
LN
HEATING ELEMENT
Relay
HEATING ELEMENT
POWER SWITCH
TRANSFORMER
POWER CORD
EARTH LINE
TERMINAL
PROBE
CIRCUIT PANEL

June 2017
Parts Diagram and Replacement Parts for the Single Wafe Maker

June 2017
BWM-7/R - Belgian Waffle Maker 7" Round
Diagram Number Description QTY
1Upper Rotating Arm 1
2Screw 2
3Head Screw 2
4Body 2
5Washer 2
6Nut 4
7Nut 2
8Hexagonal Screw 2
9Socket Screw 2
10 Cross Beam 2
11 Presser Bit for Heating Elements 2
12 Upper Pan 1
13 Handle 1
14 Nut 3
15 Lower Pan 1
16 Presser Bit for Heating Elements 1
17 Nut 6
18 Cross Screw 8
19 Spacing Pipe 4
20 Spacing Pipe 2
21 Screw 4
22 Screw 4
23 Cross Head Screw 4
24 Rubber Ring 3
25 Switch 1
26 Facial 1
27 Cross Head Screw 4
28 Foot 4
29 Bottom Board 1
30 Controlling Board 1
31 Electrical Parts Base 1
32 Contactor 1
33 Terminal 1
34 Transformer 1
35 Bottom Board 1
36 Bracket for rotating Arm 1
37 Hexagonal Bolt 4
38 Rubber Ring 1
39 Back Board 1
40 Socket Screw 2
41 Collision Bead 2
42 Bracket for Collision Bead 1
43 Spacing Board 1
44 Spacing Pin 1
45 Angle Spacing Sleeve 1
46 Bearing Bracket 1
47 Socket Screw 2
48 Cross Screw 4
49 Back Board 1
50 Rotating Shaft 1
51 Nut 5
52 Lower Rotating Shaft 1
53 Hexagonal Bolt 2
54 Shaft Circlip 1
55 Probe and Heating Wire 1
56 Crumb Tray 1
57 Nut 1
VER1114
BWM-7/R - Belgian Waffle Maker 7" Round
Diagram Number Description QTY
1Upper Rotating Arm 1
2Screw 2
3Head Screw 2
4Body 2
5Washer 2
6Nut 4
7Nut 2
8Hexagonal Screw 2
9Socket Screw 2
10 Cross Beam 2
11 Presser Bit for Heating Elements 2
12 Upper Pan 1
13 Handle 1
14 Nut 3
15 Lower Pan 1
16 Presser Bit for Heating Elements 1
17 Nut 6
18 Cross Screw 8
19 Spacing Pipe 4
20 Spacing Pipe 2
21 Screw 4
22 Screw 4
23 Cross Head Screw 4
24 Rubber Ring 3
25 Switch 1
26 Facial 1
27 Cross Head Screw 4
28 Foot 4
29 Bottom Board 1
30 Controlling Board 1
31 Electrical Parts Base 1
32 Contactor 1
33 Terminal 1
34 Transformer 1
35 Bottom Board 1
36 Bracket for rotating Arm 1
37 Hexagonal Bolt 4
38 Rubber Ring 1
39 Back Board 1
40 Socket Screw 2
41 Collision Bead 2
42 Bracket for Collision Bead 1
43 Spacing Board 1
44 Spacing Pin 1
45 Angle Spacing Sleeve 1
46 Bearing Bracket 1
47 Socket Screw 2
48 Cross Screw 4
49 Back Board 1
50 Rotating Shaft 1
51 Nut 5
52 Lower Rotating Shaft 1
53 Hexagonal Bolt 2
54 Shaft Circlip 1
55 Probe and Heating Wire 1
56 Crumb Tray 1
57 Nut 1
VER1114
BWM-7/R - Belgian Waffle Maker 7" Round
Diagram Number Description QTY
1Upper Rotating Arm 1
2Screw 2
3Head Screw 2
4Body 2
5Washer 2
6Nut 4
7Nut 2
8Hexagonal Screw 2
9Socket Screw 2
10 Cross Beam 2
11 Presser Bit for Heating Elements 2
12 Upper Pan 1
13 Handle 1
14 Nut 3
15 Lower Pan 1
16 Presser Bit for Heating Elements 1
17 Nut 6
18 Cross Screw 8
19 Spacing Pipe 4
20 Spacing Pipe 2
21 Screw 4
22 Screw 4
23 Cross Head Screw 4
24 Rubber Ring 3
25 Switch 1
26 Facial 1
27 Cross Head Screw 4
28 Foot 4
29 Bottom Board 1
30 Controlling Board 1
31 Electrical Parts Base 1
32 Contactor 1
33 Terminal 1
34 Transformer 1
35 Bottom Board 1
36 Bracket for rotating Arm 1
37 Hexagonal Bolt 4
38 Rubber Ring 1
39 Back Board 1
40 Socket Screw 2
41 Collision Bead 2
42 Bracket for Collision Bead 1
43 Spacing Board 1
44 Spacing Pin 1
45 Angle Spacing Sleeve 1
46 Bearing Bracket 1
47 Socket Screw 2
48 Cross Screw 4
49 Back Board 1
50 Rotating Shaft 1
51 Nut 5
52 Lower Rotating Shaft 1
53 Hexagonal Bolt 2
54 Shaft Circlip 1
55 Probe and Heating Wire 1
56 Crumb Tray 1
57 Nut 1
VER1114
Replacement Parts for the Single Wafe Maker

June 2017
Parts Diagram and Replacement Parts for the Double Wafe Maker

June 2017
Diagram No. Description Qty
1
Upper rotating arm 2
2
Screw 4
3
Head screw 4
4
Body 4
5
Washer 4
6
Nut 4
8
Hexagonal screw 4
9
Socket screw 4
10
Cross beam 4
11
Presser bit for heating
elements
4
12
Heating elements 4
13
Upper pan 2
14
Handle 2
15
Nut 2
16
Lower pan 2
18
Nut 8
19
Cross screw 8
21
Spacing pipe 4
22
Screw 8
23
Cross head screw 4
24
Bushing A 4
25
Switch 2
26
Facial 2
27
Cross head screw 4
28
Foot 4
29
Bottom board 1
30
PC board 2
31
Electrical parts base 2
33
Terminal 2
35
Bottom board 1
36 Bracket for rotating arm 2
37
Hexagonal bolt 4
38
Snap Bushing 2
39
Back board 1
40
Socket screw 4
42
Collision bead 2
43
Spacing board 2
44
Spacing pin 2
45 Angle spacing sleeve 2
46
Bearing bracket 2
47
Socket screw 4
48
Cross screw 4
49
Back board 1
50
Rotating shaft 2
51
Nut 4
52
Lower rotating shaft 2
53
Hexagonal bolt 4
54
Shaft circlip 2
55
Probe( PC board includes
probe)
2
56
Nut 2
57
Crumb tray 2
Diagram No. Description Qty
1
Upper rotating arm 2
2
Screw 4
3
Head screw 4
4
Body 4
5
Washer 4
6
Nut 4
8
Hexagonal screw 4
9
Socket screw 4
10
Cross beam 4
11
Presser bit for heating
elements
4
12
Heating elements 4
13
Upper pan 2
14
Handle 2
15
Nut 2
16
Lower pan 2
18
Nut 8
19
Cross screw 8
21
Spacing pipe 4
22
Screw 8
23
Cross head screw 4
24
Bushing A 4
25
Switch 2
26
Facial 2
27
Cross head screw 4
28
Foot 4
29
Bottom board 1
30
PC board 2
31
Electrical parts base 2
33
Terminal 2
35
Bottom board 1
36 Bracket for rotating arm 2
37
Hexagonal bolt 4
38
Snap Bushing 2
39
Back board 1
40
Socket screw 4
42
Collision bead 2
43
Spacing board 2
44
Spacing pin 2
45 Angle spacing sleeve 2
46
Bearing bracket 2
47
Socket screw 4
48
Cross screw 4
49
Back board 1
50
Rotating shaft 2
51
Nut 4
52
Lower rotating shaft 2
53
Hexagonal bolt 4
54
Shaft circlip 2
55
Probe( PC board includes
probe)
2
56
Nut 2
57
Crumb tray 2
Diagram No. Description Qty
1
Upper rotating arm 2
2
Screw 4
3
Head screw 4
4
Body 4
5
Washer 4
6
Nut 4
8
Hexagonal screw 4
9
Socket screw 4
10
Cross beam 4
11
Presser bit for heating
elements
4
12
Heating elements 4
13
Upper pan 2
14
Handle 2
15
Nut 2
16
Lower pan 2
18
Nut 8
19
Cross screw 8
21
Spacing pipe 4
22
Screw 8
23
Cross head screw 4
24
Bushing A 4
25
Switch 2
26
Facial 2
27
Cross head screw 4
28
Foot 4
29
Bottom board 1
30
PC board 2
31
Electrical parts base 2
33
Terminal 2
35
Bottom board 1
36 Bracket for rotating arm 2
37
Hexagonal bolt 4
38
Snap Bushing 2
39
Back board 1
40
Socket screw 4
42
Collision bead 2
43
Spacing board 2
44
Spacing pin 2
45 Angle spacing sleeve 2
46
Bearing bracket 2
47
Socket screw 4
48
Cross screw 4
49
Back board 1
50
Rotating shaft 2
51
Nut 4
52
Lower rotating shaft 2
53
Hexagonal bolt 4
54
Shaft circlip 2
55
Probe( PC board includes
probe)
2
56
Nut 2
57
Crumb tray 2
Replacement Parts for the Double Wafe Maker
BWM-7/R-2 - Belgian Wafe Maker - Double Round 7”

June 2017
ACE Equipment One Year Limited Warranty
Admiral Craft Equipment Corp. (ACE) warrants its equipment against defects in materials and workmanship, subject
to the following conditions:
ACE Equipment is warranted for one year, effective from the date of purchase by the original owner. A copy of the
original receipt or other proof of purchase is required to obtain warranty coverage. This warranty applies to the original
owner only, and is not assignable.
Should any product fail to function in its intended manner under normal use within the limits defined in this
warranty, at ACE’s discretion, such product will be repaired, replaced with arefurbished unit, or replaced with a new
unit by ACE, after defective unit has been inspected and defect has been confirmed. ACE does not assume any liability
for extended delays in replacing any item beyond its control. This warranty does not apply to rubber and non-metallic
synthetic parts that may need to be replaced due to normal usage, wear or lack of preventative maintenance.
This warranty covers products shipped into the 48 contiguous United States, Hawaii, and metropolitan areas of Alaska
and Canada. Warranty coverage on products used outside the 48 contiguous United States, Hawaii and metropolitan
areas of Alaska and Canada may vary. Contact ACE for details at 1-800-223-7750
The following conditions are not covered by warranty:
• Equipment failure relating to improper installation, improper utility connection or supply and problems due to
improper ventilation.
• Equipment that has not properly been maintained, damage from improper cleaning, and water damage
to controls.
• Equipment that has not been used in an appropriate manner, or has been subject to misuse, neglect, abuse,
accident, alteration, negligence, damage during transit, delivery or installation, fire, flood, riot, or act of God.
• Equipment that has the model number or serial number removed or altered.
• Equipment on which the security seal has been broken.
If the equipment has been changed, altered, modified, or repaired without express written permission from ACE, then the
manufacturer shall not be liable for any damages to any person or to any property, which may result from the use of this
equipment thereafter.
This equipment is intended for commercial use only and this warranty is void if equipment is used in other than a
commercial application.
For warranty and non-warranty related issues,technical support,purchase replacement parts and warranty registration
visit www.admiralcraft.com.Please have your model number, serial number and proof of purchase ready. It is not
necessary to contact the place where you originally purchased your product from.
“THE FOREGOING WARRANTY IS IN LIEU OF ANY AND ALL WARRANTIES EXPRESSED OR IMPLIED
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILTY OR FITNESS FOR PARTICULAR
PURPOSES AND CONSTITUES THE ENTIRE LIABILITY OF ACE. IN NO EVENT DOES THE LIMITED
WARRANTY EXTEND BEYOND THE TERMS STATED HEREIN.”
VER1212