Adexa ZBS-15 User manual

Instruction Manual
ZBS-15 Ice Maker & Crusher
Thank you for choosing our ice maker
Please read this Instruction Manual carefully before using this product so as to ensure proper use.
After reading this manual, please keep it in a safe place and refer to it when necessary.

Safety Notice
In order to avoid any accidents, please refer to following operation:
1. Disconnect power before servicing.
2. Do not pull directly on wire when plugging or unplugging the unit.
3. If ice is abnormal, please call the seller.
4. It is normal for the compressor and condenser surface to reach temperatures between 70°C and
90°C during operation and surrounding areas may be hot. Please don't touch it.
5. Due to fast freezing, ice cubes may appear “Cloudy”. This is trapped air in the water and it will not
affect quality or taste of ice.
6. When out of use, please open the drawer at least 2cm to allow for air circulation and avoid any
metallic components becoming rusted.
7. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a
similarly qualified person in order to avoid a hazard.
8. This appliance can be used by children aged from 8years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards
involved.
9.Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision
10. WARNING: fill with bottled or good quality tap water only. (Do not fill with fruit juices or other drink
types).
11. WARNING –Keep the air vents on the sides of the machine unblocked at all times.
12. WARNING –Do not use mechanical devices or other means to accelerate the defrosting process,
other than those recommended by the manufacturer.
13. WARNING –Do not damage the refrigerant circuit.
14. WARNING –Do not use electrical appliances inside the food storage compartments of the
appliance, unless they are of the type recommended by the manufacturer.
Description
1
7
2
3
10
4 8 11
5 9
6
12
1
Viewing window
2
LCD Screen
3
Control Panel
4
Crushed Ice & Water Outlet

5
Water Puncher
6
Water Collecting Tray
7
Ice Outlet
8
Water Reservoir Door
9
Ice Puncher
10
Nameplate
11
Water Inlet Hole
12
Power Cord
Specifications
Daily Ice Output : 15-18kg/24h
Ice Storage Capacity: 600g
Water Reservoir Capacity : 1.8L
Refrigerant R600a
Dimension 340*450*453mm
Before/First Use of Your Ice Maker
1.During transportation, the incline angle of the cabinet should not be over 45° .Do not turn the Ice
maker upside down.As this may damage the compressor and sealed system.
2.Remove all packing material and carefully check your ice maker to ensure it is in good condition and
that there is no damage to the ice maker or power cord and plug.
3.The Ice maker should be placed horizontally on a level surface.To ensure proper ventilation for your
Ice maker allow 150mm of space at the top, the back and on each side. Do not install the Ice maker
near an oven, radiator, or any other heat source.
4.Before using the Ice maker for the first time, please wait 2 hours after positioning it, and keep the front
lid open for at least 2hours
5.Ensure that the voltage indicated on the ice maker corresponds with the voltage in your home.
6.Pure water is not allowed to be used on this unit, spring water is recommended.
7.Please always keep the viewing window close during ice making.
Control Panel Operation
Display
Explanation
The unit has problem,need to take off the plug,and restart it.
If it appears again,then ask for service
Ice is full
Water is not enough in water reservoir, need to add water
Unit is dispensing ice cubes
Unit is dispensing water

Ice on making, if S at right top hand of it,then means small size ice on making
if L at right bottom hand,then means large size ice on making
Crushed ice in process
Button
Operation
CRUSHED ICE
Press it, get to get the crushed ice.
Press it again, the unit will stop crushed ice in 5seconds
SMALL or LARGE
Press button SMALL to turn on/off the small size ice making function
Press button LARGE to turn on/off the large size ice making function
ON/OFF
Press it to turn on or off the power
Operating Instructions
Step 1
Plug in the machine into the socket.
Step 2
Add water as Sketch Aor Sketch B
Sketch A Add Water by Manual
Sketch B Connect Unit to Water Faucet
Step 3
Press ON/OFF button to turn on or off the power.
Step 4
Water will be pumped into the water tray from the water reservoir automatically,this takes about 30
seconds
Note: If no water is pumped to the water tray over two cycles but the water in reservoir is enough, then
please open the drain cap, and let several drops water runs out. Then press ON/OFF button
again to restart the unit
Step 5
Select the button SMALL,LARGE to start the ice making function you may need

Note: when temperature lower than 15degrees,S/SMALL is recommended,when temperature over
30degrees,L/LARGE ice is recommended.
Step 6
Ice making cycle begins,ice will be frozen onto the evaporator fingers.
Step 7
Once ice making cycle is finished,the water tray will tilt forward; the remaining water flows back to the
water reservoir and the ice cubes will drop from the fingers.
Step 8
In about 15-35 seconds, the water tray will tilt backward,ice will be pushed to ice reservoir directly,unit
back to work from step 4 to step 6 again
Step 9
Push the ice cube dispenser puncher button to get ice, the indicator will be on
Note: Please put your cup below the ice cube dispenser shoot directly.
Notice: If the ice is stored in the unit for long time,the ice may freeze and stick together,then no ice will
be
dispensed even the ice is full,if so,please kindly use scoop included in the unit to break the ice
first,then push the puncher button.
Step 10
Press the ,unit start to dispense crushed ice,press it again,the unit will stop crushed
ice in 5seconds.
Step 11
Press ON/OFF button to turn off power of unit
Step 12
Push the puncher at left side of the unit,cold water will come out
Note: if you need to get cold water,at least the ice making function should be turn on.
Please make sure your cup is below the cold water outlet,or water will be splashed every where
Step 12
If you need to take off the pipe,replace it or insert the anti drain plug,please do as follows:
Firstly take off the blue ring named as A,then press the white ring(lock) at the outer side named as B,At
last take out the pipe
Caring
1.Clean the inner liner, ice collecting tray, water box, ice shovel and evaporator frequently. When
cleaning, unplug the unit and remove the ice cubes. Use a diluted solution of water and vinegar to clean
the inside and the outside surface of the ice maker. Do not spray ice maker with chemicals or diluted
agents such as acids, gasoline or oil. Rinse thoroughly before starting.
2.Keep ventilation openings in the appliance enclosure, or in the built-in structure, clear of obstruction. Do

not use mechanical devices or other means to accelerate the defrosting process, other than those
recommended by the manufacturer.
3.Always use fresh water before starting ice production either at initial installation or after a long shut-off
period.
Troubleshooting
1. Please note, if a power failure occurs due to disconnection of the power cord, or the off power button
has been pushed off during an ice making cycle, small ice chips may formed and lodge in the automatic
shovel causing it to jam. If this occurs, the ice chips may be removed by disconnecting the power cord
and gently pushing the shovel to the rear of the cabinet and removing the ice chips, then restarting.
2. Please restart the ice maker by pressing Stop and then Start. If the ice shovel does not push the ice
into the ice collector after the formed ice drops from the evaporator finger while at the same time the M
light is on, check to see if the water tray is horizontal or balanced. If not then adjust by pressing the ice
shovel lightly with your finger. Then re-start the ice maker.
Problem
Possible Reasons
Suggested Solutions
The compressor works
abnormally with a Buzzing
noise.
The voltage is lower than
recommended.
Stop the ice maker and do not restart
until the voltage is normal.
The compressor is hurt
during transportation
Stop right away,and keep it on a flat
surface for 24h,then restart
ADD WATER indicator lights
up
The water is not enough
Fill water to the MAX line,then press
the start button to restart.
The pump is full of air
Open the drain cap,and let several
drops water runs out,then restart
The pump is blocked
Clean the water pump after take it out
The pump is broken
Replace pump
Indicator lights on display are
not on.
Blown fuse/ No power
Replace fuse / Turn power on
The Ice made is too large
and with pieces sticking
together.
Wrong ice size is selected
Select small size if temperature is cool
Ice from previous batch left
in the ice tray
Stop the unit right away,restart the unit
till the ice in water tray melt down
The evaporator is too low
Shift the evaporator a little up.
Ice made,but no push the ice
basket
The ice shovel is broken
Replace the ice shovel
indicating
Water tray is blocked by ice
cube.
Clear the ice under the ice shovel,then
restart the machine
The motor is dead
At standby mode,push the water tray
back till a click sound and then pull it
forward till a click,do this for
5times.Then restart the unit
Machine is running,but water
is warmer than beginning
Magenetic valve is dead
Turn on the unit for 1minute,stop and
take off the plug.repeat for 5times
,restart the unit
Magnetic valve is broken
call for service

Ice is made,however it won’t
drop from evaporator
Magnetic valve is broken
call for service
PCB is broken
Ice making process is right,
but no ice is made.
There is no refrigerant in
the compressor
call for service