ADTRAN 424RG User manual

Q
uic
k
Start
DESCRIPTION
The 424RG/434RG Optical Network Terminal (ONT) Fiber Tray
and Wall Mount Bracket (ONT Fiber Tray and Bracket) is used to
mount either of the following ONTs to a wall:
■ADTRAN 424RG 2 POTS/4 GigE Dual Band WiFi ONT
(P/N 1287781F1)
■ADTRAN 434RG 2 POTS/4 GigE RF MoCA Dual Band WiFi
ONT (P/N 1287782F1)
Required Tools
The following tools are required when installing the ONT Fiber
Tray and Bracket.
■Power drill (optional)
■Carpenter’s level (optional)
■Phillips-head Screwdriver
■Hammer
Installation Steps
To install the ONT Fiber Tray and Bracket, complete the following
steps:
1. Select Location and Mount Bracket.
2. Attach Incoming Fiber Cable to Bracket.
3. Remove Base (if required) from ONT.
4. Remove Logo Panel from ONT.
5. Connect Incoming Fiber Cable to ONT.
6. Attach ONT to ONT Fiber Tray and Bracket.
Step 1: Select Location and Mount Bracket
Select a location to mount the ONT Fiber Tray and Bracket near
the fiber entrance. Use the supplied hardware to mount the
bracket to the wall as follows:
Supplied hardware is intended for drywall mounting only. For
mounting on surfaces other than drywall, obtain the appropriate
mounting hardware and follow the provided instructions.
1. Refer to Figure 1 and mark hole locations using the ONT
Fiber Tray and Bracket as a template. Use a carpenter’s
level to ensure the bracket is level.
2. Start anchor into the wall by using a hammer to lightly tap
the anchor in until the threads are close to the wall.
gNOTE
Pre-drill holes using a 1/4” drill bit if difficulty is encountered.
3. Insert either a No. 2 or No. 3 Phillips driver bit into the recess
of the anchor head.
4. Using gentle forward pressure, rotate the wall anchor
clockwise until the collar is flush with the wall.
5. Align the ONT Fiber Tray and Bracket with the anchors.
Insert and tighten the #6 screws until the bracket is secured
to the wall.
Figure 1. Select Location and Mount Bracket
Step 2. Attach Incoming Fiber Cable to Bracket
Refer to Figure 2 and wrap any excess incoming fiber around the
ONT Fiber Tray and Bracket.
Do not exceed a minimum bend radius of 2-inches when installing
fiber cabling.
Figure 2. Attach Incoming Fiber Cable to Bracket
Incoming
Fiber
Incoming
Fiber
ADTRAN ONT
424RG/434RG
Fiber Tray and Wall Mount Bracket
January 2018
61287412F1-13A
P/N: 1287412F1

2 61287412F1-13A
Figure 5. Connect Incoming Fiber Cable to ONT
Step 6: Attach ONT to ONT Fiber Tray and Bracket
1. Refer to Figure 5 and position the ONT Mounting Sots so
that these align with the Mounting Bracket Tabs on the ONT.
2. Refer to Figure 6 and position the ONT so that the two
mounting tabs on the top of the ONT Fiber Tray and Bracket
align with the mounting slots in the back of the ONT.
3. Refer to Figure 6 and gently push the ONT towards the ONT
Fiber Tray and Bracket until the ONT snap onto the bracket.
Figure 6. Attach ONT to ONT Fiber Tray and Bracket
Mounting
Bracket Tabs
ONT
Mounting Slots
Step 3. Remove Base (if required) from ONT
Refer to Figure 3 and remove the screw that holds the base to the
bottom of the ONT.
After the base has been removed, reinsert the screw into the
bottom of the ONT and tighten.
Figure 3. Remove Base from ONT
Step 4. Remove Logo Panel from ONT
Refer to Figure 4 and remove the Logo Panel from the ONT by
pulling it straight out from the ONT housing.
Figure 4. Remove Logo Panel from ONT
Step 5. Connect Incoming Fiber Cable to ONT
Refer to Figure 5 and connect the Incoming Fiber Cable to the
Fiber Connector on the bottom of the ONT.
Screw
Logo
Panel

61287412F1-13A 3
Once all cables have been reconnected, refer to the LED table
below to ensure the ONT is operating properly.
424RG and 434RG LEDs
“*” This indicates the use of the feature is dependant upon provisioning by network
personnel.
“**” This option is only available on the 434RG ONT.
Label Status Indication
POWER 

Off
Green
AC or battery off
No Failure
FIBER 

2
Off
Green
Green Flashing
Fast
No connection to the OLT,
open fiber, failure at the ONT,
or power is Off
DS signal present and is within
operating range
Ranging in Progress or AOE
Auto-upgrade in progress
INTERNET 

Off
Green
No IP address configured on
WAN Interface, or Power is Off
WAN Interface is configured
with IP address
GE 1-4 

2
Off
Green
Green Flashing
Fast
Link is down or not connected
Link is up
Data is being sent or received
USB 

2
Off
Green
Green Flashing
Fast
Power Off or no device
connected
Device connected
Data is being sent or received
2.4GHZ* 

2
Off
Green
Green Flashing
Fast
Power is Off, or Wireless
2.4GHz is Disabled
Wireless 2.4GHz is Enabled
Data is being sent or received
on 2.4GHz
5GHZ* 

2
Off
Green
Green Flashing
Fast
Power is Off, or Wireless 5GHz
is Disabled
Wireless 5GHz is Enabled
Data is being sent or received
on 5GHz
PHONE 1-2 

2
Off
Green
Green Flashing
Slow
Unequipped or on-hook and
not ringing
Line is off-hook
Line in ringing state
RF+MOCA** 

2

Off
Green
Yellow Flashing
Red
No RF connection
RF-only connection
MoCA-only connection
RF+MoCA down
WPS* 

2
Off
Green
Green Flashing
Fast
Power Off or WPS is Disabled
WPS is Enabled
WPS push button pressed and
device is ready to accept
connection

Documentation for ADTRAN Network Solutions products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following online documents and resources provide additional information for this product:
ADTRAN 424RG 2 POTS/4 GigE Dual Band WiFi Residential Gateway ONT Job Aid
ADTRAN 434RG 2 POTS/4 GigE/RF MOCA Dual Band WiFi ONT Job Aid
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can be
found online at www.adtran.com/warranty.
Trademarks: Brand names and product names included in this document are trademarks,
registered trademarks, or trade names of their respective holders.
©2018 ADTRAN, Inc. All Rights Reserved.
CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61287412F1-13A*