Advance acoustic PANORAMIC 31 AS750 Owner's manual

ADVANCE
PANORAMIC
Installation and Operation
Instructions
3-Sided Electric Fire
ADVANCE PANORAMIC 31 AS750
ADVANCE PANORAMIC 41 AS1000
ADVANCE PANORAMIC 53 AS1300
ADVANCE PANORAMIC 60 AS1500
ADVANCE PANORAMIC 72 AS1800
ADVANCE PANORAMIC 80 AS2000

1
TABLE OF CONTENTS
IMPORTANT INFORMATION ................................................ 2
UNPACKING ............................................................................. 3
OPTIONAL SIDE PANELS ........................................................................... 4
PRODUCT INFORMATION .................................................... 5
PRODUCT TECHNICAL INFORMATION ................................................. 5
PRODUCT DIMENSIONS ............................................................................ 5
MANUFACTURERS INFORMATION ........................................................ 5
INSTALLATION AND LOCATION ......................................... 6
PLACING THE LOGS AND EMBERS ......................................................... 8
OPERATING THE FIRE............................................................. 9
MANUAL CONTROL ................................................................................... 9
REMOTE CONTROL .................................................................................. 10
WI-FI / SMART CONTROL ......................................................... 13
USING THE APP .......................................................................................... 17
MAINTENANCE INSTRUCTIONS ........................................ 18
CLEANING .................................................................................................. 18
SAFETY FEATURES .................................................................................. 18
ENVIRONMENT ...................................................................... 19
WARRANTY ............................................................................ 20
Please follow the installation instructions carefully and
then retain these instructions for future reference.

2
Important information:
Keep the front of the fire at least 3 FEET AWAY from combustible materials. These
include but are not limited to: articles of clothing, curtains, cushions, furniture, other
soft furnishings and papers.
In order to avoid the product overheating please DO NOT cover the heater.
Always turn OFF and unplug the heater when it is not in use.
DO NOT use if the appliance or its cables are damaged.
NEVER place near bodies of water. These include but are not limited to: bathtubs,
fountains, ponds and other water containers.
NEVER allow any objects to enter or obscure any ventilation or exhaust openings as
this may result in an electrical shock, damage to the product or may result in a FIRE.
A heater contains hot and/or sparking components inside, Therefore, DO NOT use in
areas where flammable gases, flammable liquids, paint and petrol are used or stored.
AVOID the use of extension cables and timers to avoid FIRE.
This appliance IS NOT freestanding and should not be used as such.
ALWAYS use properly grounded fused and polarised outlets.
ALWAYS use ground fault protection where required by electrical codes.
To AVOID burns and/or personal injury NEVER touch any of the hot surfaces such as
the heater vent.
Power MUST BE DISCONNECTED before any cleaning, relocation or maintenance.
Any replacement of circuitry or outlets should ONLY be performed by a certified
electrician.
To prevent a potential fire DO NOT attempt to burn any materials in the heater. .
These include but are not limited to: marshmallows, paper and wood.
DO NOT store or keep during transportation, outdoors or in a damp environment.
NOT TO BE installed below an electrical socket outlet.
DO NOT leave children unsupervised whilst the appliance is switched on.
Please read the instructions carefully BEFORE installation.

3
Use this product ONLY as described in this instruction manual. Any other
use is discouraged in order to prevent bodily harm and/or fire.
Unpacking:
Congratulations on your new electric fire. In order to unpack your
product without causing any damage to yourself of the product, please
take care and follow the instructions.
1.
Place the box on a flat surface. Make sure you have enough
space.
2.
Remove any rings or bracelets which may scratch the product
or be damaged during removal.
3.
Carefully remove the appliance from the box and put all
packing aside.
4.
Please keep the original packing for further storage or
transportation.
5.
Prior to installation, test the product to check that the
appliance is functioning correctly.
Keep plastic bags away from children and animals!

4
Optional Side Panels
When unpacked the fire has only one pane of glass visible at the front.
The two side sections are covered by blanking plates.
If the fire is to be installed as a two or three sided appliance these
plates need to be removed. To do this unscrew the fire frame from the
body of the fire, remove the panel and then refit the fire frame.

EVOLUTION FIRES
EF750 Panoramic HD
EF1000 Panoramic HD
EF1300 Panoramic HD
EF1500 Panoramic HD
EF1800 Panoramic HD
EF2000 Panoramic HD
750 617 792 328
1000 617 1042 328
1300 617 1342 328
2000 617 2042 328

6
Please read the instructions carefully BEFORE installation.
The installation MUST be carried out by a qualified person.
Installation and location:
Connect the appliance to a single-phase AC supply of the voltage
specified on the ratings plate.
In the instance that the fire is connected directly to the mains
electricity supply, a fused switched spur with a 13 amp fuse must be
fitted.
The power supply must be able to handle 2000 watts (2kw).
This appliance must be earthed
Do not use an extension lead or a timer.
Always ensure that all electrical work complies with the relevant
building regulations and the electrical code of practice.
This product is designed to be either wall mounted and / or fitted and
fixed inside a frame. This appliance has multiple electrical
components that must be kept away from water and damp or moist
conditions.

7
This product should be fitted to one of the following options:
1.
Wall Mounted – Using the H bracket which is located on the
back of the appliance. It is important to use fixtures that are
appropriate for the type of wall. The wall must be of sound
construction and able to hold the weight of the appliance.
2.
Mounted on a solid base – Please keep a distance of at least 5
cm from any non-combustible materials.
3.
Fitted into a Studded Wall – Which needs to be finished with
either plasterboard or a plastered finish. The fire can then be
installed with the facing trim of the fire flush up to the plastered
finish. See Drawings below:

8
Make sure that the cable is not run across the heater and can be
plugged into the mains socket without the use of an extension cable.
Please make sure that the plug socket outlet is in a location that is
easily accessible. The appliance should be switched off when not in
use and for maintenance.
Placing the logs and embers:
The accessory box which is packed inside the fire contains the mixed
black and white nuggets that create the fire bed. These should be
placed on the base of the fire in a random manner. The logs are then
placed in a position of your choice on top of these. The logs are
delicate and should be handled with care.

9
Operating the fire:
Manual control:
This appliance can be operated manually using the controls situated
on the top right hand side of the fire screen.
ON/OFF POWER SWITCH- This switch is used to turn the mains
supply to the appliance on or off. When the switch is in the ON
position an orange indicator light will show in the middle of the
screen. This needs to be in the on position for both manual and remote
operation.
STANDBY- Used to switch the appliance ON or OFF into standby
mode.
FLAME-Pressing this button will cycle through the four different
flame brightness levels.
HEATER- Use this button to select low heat, high heat or heater off.
When low heat is selected the indicator light will glow orange.
When high heat is selected the indicator light will glow red.
Please note that the heater will only operate when the room
temperature is below the temperature on the handset, which can be
adjusted using the remote or through the app. When the heater
switches off the fan will continue to run to cool the appliance.
MODE- Shuffle through a selection of pre-programmed effects.

10
Remote control:
Remove the battery / control panel cover by sliding
completely down and insert 2 x AAA batteries ensuring the
batteries are fitted correctly. Refit the cover by sliding back up
to the original position. Please ensure old batteries are
disposed of responsibly by contacting your local authority
about recycling schemes.
Ensure that the ON / OFF Power Switch on the fire is in the
ON position.
Point the remote-control handset directly towards the fire and
press the appropriate button to operate the fire. Sliding the
door down on the remote control will reveal more buttons
which offer additional functions. Otherwise using the basic
remote buttons will operate the fire in the same way as the
manual control buttons.
Setting the colour functions Press lamp
button:
1
2
3
Will change colour of flame, ash bed, ember separately.

11
Setting the Time:
1. Press the clock setting button, which will start the
day cursor to blink. Using clock up and clock down
buttons set to the current day e.g. Monday - 1, Tuesday - 2,
Wednesday - 3 etc.
Press to confirm the required day.

12
2. The hour setting will now be blinking, adjust using
and to the desired hour and confirm using
3. The minute setting will now be blinking, adjust using
clock up and buttons to the desired minutes and confirm using
the clock setting button.
Adjusting the desired temperature
Whilst the fire is switched on, use temperature up and
down to set the desired room temperature.
A confirmation beep will be heard from the fire. If the room
is already warmer than the temperature set then the heater will
switch off until the thermostatic sensor detects a fall in
temperature.
Adaptive Control
Adaptive control works in target temperature 25°C with high
heat.

13
Wi-Fi / Smart control:
Preparation
In order to prepare please check that your mobile phone is connected to your Wi-Fi router.
Plug your fire in to the wall. Switch the fire on at the wall socket. DO NOT use the
STANDBY button to turn on, use the power switch. You should see an orange dot appear on
the screen.
The buttons on the fire are as follows:
1. Download the ‘Smart Life’ APP
• The app is free on both Google play and the app store.
• Please search ‘Smart Life – Smart Living’.
• Download the app.
2. Open the Smart Life App, Register and Log in
• Open the app and click the register button, unless you have an existing
account, then please log in with your existing details.
• Input an email, the app will send a code in order to verify your email.
• Once you have received the code, input the code and create your password.

14
3. Add your device
 Please touch the ‘Add device’ button or the
‘Add’ symbol to add your device.
Scan the QR code
 Touch the ‘SCAN’ symbol.
 Scan the below QR code.

15
5. Connecting to your Wi-Fi
 Select your Wi-Fi network and input the password of
your Wi-Fi network.
6. Establishing a connection
• Give a long press to the standby button for around
3 seconds.
• You should see a red light next to the orange dot in
the middle of the fire screen. The red light should
be blinking quickly on the screen. Roughly 2 times
per second.
• When prompted, if the red light is blinking rapidly,
confirm that the indicator is rapidly blinking by
checking the circle and then by pressing ‘Next’

16
7. Adding your device
• Wait whilst the app adds the device. Please keep
the phone close to the device whilst the device is
syncing.
• If it fails to sync Repeat steps 4,5 and 6
8. Your device has been added successfully.
 Now your device has been successfully added click
on the device and you are ready to start using your
phone to control your fire.

17
Along the top of the screen there are 5 tabs ‘Heat, Flame, Ember,
Logs and Mode’
Heat- use this tab to control the temperature.
Flame- use this tab to control the colours of the flames.
Ember- use this tab to control the colours of the embers.
Logs- use this tab to control the colours of the Logs.
Mode- chose one of the preprogramed modes.
For the flame, ember and logs settings you can turn the default
Orange colour on / off by clicking the button and can add additional
colours by pressing the colour wheel and then selecting your
preferred colour from the big wheel above. Both the orange button
and the colour wheel button can be pushed on and off.
Using the App
1. To turn the fire on press the
standby button at the bottom
of the screen
2. To set timers press the
clock button at the bottom
left of the screen. 7 day timer
is available on the APP
The 7 day timer is available
within the clock function.

18
Maintenance:
You MUST remove the plug from the socket outlet and allow the
heater to cool completely before cleaning or maintenance.
Maintenance should only be carried out by a qualified person.
Cleaning:
A soft dry cloth, such as microfiber cloths, can be used to remove dust
and for general day to day care.
If a more thorough clean is needed a damp cloth, NOT WET, may be
used to wash the exterior surfaces. The glass can be cleaned with glass
cleaner and a soft cloth.
THE APPLIANCE MUST FULLY DRY BEFORE USING THE HEATER.
Safety features:
As this appliance contains a heating component there is an automatic
thermal cut out safety feature. This feature stops the product from
overheating and from potentially causing a fire.
If the appliance reaches a temperature above the guideline parameters
the automatic thermal cut out safety feature will activate and the
heater will cut out. However, the fans will continue to run in order to
cool down the appliance.
Once sufficiently cooled the automatic thermal cut out safety feature
will automatically reset and the heater will be restarted.
If this problem continues, turn off the fire and disconnect from the
plug socket. Check that none of the ventilation vents are obstructed. If

19
WARNING!
The heater should NEVER be submerged in water.
The interior should NEVER be wet.
Cleaning chemicals such as but not limited to detergents, alcohols
and abrasives should NOT be used.
your fire is connected to a chimney, the chimney must be blocked off
as the drafts can affect the appliance.
If the problem continues, keep the product unplugged from the power
socket and contact your supplier.
Environment:
DO NOT throw out your appliance or its parts as municipal waste.
Contact your local government for advice on the collection services
and proper protocol in your area.
Please DO NOT dump your appliance as if not properly treated
hazardous substances can leak into water supplies effecting animals
and people’s health and wellbeing.
If you are replacing your old appliance,
retailers are legally obligated to dispose of
your old appliance without any additional
cost.