Advanced Diagnostics MVP PRO User manual

535
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
• TOYOTA (ADS-125)
• TOYOTA 2007 (ADS-150)
• TOYOTA 2010 (ADS-174)
• TOYOTA 2013 (ADS-199)
MVP - TCODE - PRO
Powered by ADVANCED DIAGNOSTICS USA
TOYOTA
This section contains:
(Optional software on some TCode units)

536 Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
TYPE 1
ALL Toyota TYPE 1 use what the industry refers to as a 4C transponder chip in
the keys.
The same 4C chip can be programmed into the car as a MASTER or as a VALET
key.
A key that is programmed as a VALET cannot be used to introduce more keys
into the system with the MVP or T-Code.
How to tell if a programmed key is a MASTER or a VALET?
Valet key- when rst inserted into the ignition lock, the Security Light will stay on for 2
seconds and then stay off.
Master key- when inserted into the ignition lock, the Security Light will not illuminate at
all.
TYPE 1 SPECIAL FUNCTIONS:
RESET Immobilizer:
This function allows you to erase all keys and to place the immobilizer in the “Auto
Learn Mode”. This function is used when the customer has lost all their keys.
ADD MASTER KEY:
This function allows you to add a Master key to the car’s immobilizer system as long as
you have an existing pre-programmed Master key to start with. On Type 1 system cars
it is possible to program a key in as Valet as a Master
ADD VALET KEY:
This function allows you to add a Valet key to the car’s immobilizer system as long as
you have an existing pre-programmed Master key to start with. The vehicle’s immobi-
lizer system cannot tell the difference between the transponder chip in the key,
so it is possible to program a Master as a Valet into the immobilizer system.
ERASE KEYS:
This function allows you to erase all keys except the key in the ignition lock at the time.
Toyota Immobilizer
MVP - TCODE - PRO
Powered by ADVANCED DIAGNOSTICS USA

537
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
MVP &
TCODE TOYOTA ADVANCED DIAGNOSTICS USA powered
by
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
VEHICLE SELECTION
> Immobilizer
REMOTE
VEHICLE SELECTION
> TYPE 1
TYPE 2
ECU IDENTIFICATION
TOYOTA/LEXUS TYPE 1
PRESS ENTER KEY
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
> SPECIAL FUNCTIONS
DIAGNOSTIC MENU
> RESET Immobilizer
ADD MASTER KEY
ADD VALET KEY
ERASE KEYS
RESET Immobilizer
GAINING ACCESS
TIME REQUIRED 16:00
TIME ELAPSED 0:28
RESET Immobilizer
PROCEDURE COMPLETE
PRESS ENTER KEY
Note: This will cause ALL keys to be
erased and put the Immobilizer system
into “Auto Learn Mode”
Note: Do not be impatient.
Some vehicles may go over 16 minutes.
If the timer goes over 35 minutes - stop.
Disconnect from the OBD2 port and re-
move the key. Wait 20 sec. and start over.
Once you have PROCEDURE COMPLETE on the tester, look at the immobilizer
light.
The Security Light can be in 2 shapes:
> A small blinking red circle next to the word “Security”, or
> A blinking red light in the shape of a car.
The light should now be solid indicating that the Immobilizer system has been
Reset and the vehicle is now in Auto Learn mode Insert each key you want to
program - but do not turn the key ON, only insert and remove after 5 seconds.
The vehicle may learn up to 3 keys this way and the Auto Learn mode should close
once the 3rd key is presented. The last key presented will be programmed in as
Valet key.
If you have less than 3 keys to program You can close the Auto Learn mode early
by pressing the brake pedal 6-8 times, very fast. (You must use a Master key for
this.)
(Use this method if you have no Master Keys.)
RESET Immobilizer - TYPE 1
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
powered
by

538 Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
VEHICLE SELECTION
> Immobilizer
REMOTE
VEHICLE SELECTION
> TYPE 1
TYPE 2
ECU IDENTIFICATION
TOYOTA/LEXUS TYPE 1
PRESS ENTER KEY
SWITCH IGNITION ON
PRESS ENTER KEY
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
> SPECIAL FUNCTIONS
DIAGNOSTIC MENU
RESET Immobilizer
> ADD MASTER KEY
ADD VALET KEY
ERASE KEYS
ADD MASTER KEY
WARNING
FOLLOW NEXT SCREENS
QUICKLY & CAREFULLY
PRESS ENTER KEY
ADD MASTER KEY
SWITCH IGNITION OFF
REMOVE MASTER KEY
WITHIN 20 Sec
AND THEN PRESS ENTER
TIME ELAPSED: 1 S
NOTE: If you do not have an existing Master key, you must use the “Reset Immobilizer” procedure to Reset
the Immobilizer system. A Valet key will not work as a substitute for a Master Key.
ADD MASTER KEY
INSERT NEW MASTER KEY
WITHIN 10 Sec
LEAVE IGNITION OFF
AND THEN PRESS ENTER
TIME ELAPSED: 0 S
ADD MASTER KEY
TIME ELAPSED: 2 S
ADD MASTER KEY
PROCEDURE COMPLETE
TIME ELAPSED: 59 S
PRESS ENTER KEY
Note: This usually takes about 60 seconds.
If the timer goes past 120 seconds, stop.
The key is most likely now programmed.
Disconnect & try key.
Note: If you get an Error message screen:
disconnect from the OBD2 port and
remove the key. Wait 20 seconds and
start over. On this Type, each key must
be added separately. Disconnect from the
OBD2 port and remove the key. Wait 20
seconds and start over to add another key.
Note: Read carefully & follow the
screen prompts.
Insert a Master key that is already registered into the vehicle. Turn the ignition lock to the “ON”
position. The Security Light must be out when the key is in. Connect and follow screens.
ADD MASTER KEY - TYPE 1
MVP &
TCODE TOYOTA ADVANCED DIAGNOSTICS USA powered
by

539
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
VEHICLE SELECTION
> Immobilizer
REMOTE
VEHICLE SELECTION
> TYPE 1
TYPE 2
ECU IDENTIFICATION
TOYOTA/LEXUS TYPE 1
PRESS ENTER KEY
SWITCH IGNITION ON
PRESS ENTER KEY
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
> SPECIAL FUNCTIONS
DIAGNOSTIC MENU
RESET Immobilizer
ADD MASTER KEY
> ADD VALET KEY
ERASE KEYS
ADD VALET KEY
WARNING
FOLLOW NEXT SCREENS
QUICKLY & CAREFULLY
PRESS ENTER KEY
ADD VALET KEY
SWITCH IGNITION OFF
REMOVE MASTER KEY
WITHIN 20 Sec
AND THEN PRESS ENTER
TIME ELAPSED: 1 S
NOTE: If you do not have an existing Master key, you must use the “Reset Immobilizer” procedure to Reset
the Immobilizer system. A Valet key will not work as a substitute for a Master Key.
ADD VALET KEY
INSERT NEW VALET KEY
WITHIN 10 Sec
LEAVE IGNITION OFF
AND THEN PRESS ENTER
TIME ELAPSED: 0 S
ADD VALET KEY
TIME ELAPSED: 2 S
ADD VALET KEY
PROCEDURE COMPLETE
TIME ELAPSED: 59 S
PRESS ENTER KEY
Note: This usually takes about 60 seconds.
If the timer goes past 120 seconds, stop.
The key is most likely now programmed.
Disconnect & try key.
Note: If you get an Error message screen,
disconnect from the OBD2 port and
remove the key. Wait 20 seconds and
start over. On this Type, each key must
be added separately. Disconnect from the
OBD2 port and remove the key. Wait 20
seconds and start over to add another key.
Note: Read carefully & follow the
screen prompts.
Insert a Master key that is already registered into the vehicle. Turn the ignition lock to the “ON”
position. The Security Light must be out when the key is in. Connect and follow screens.
ADD VALET KEY - TYPE 1
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
powered
by

540 Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
VEHICLE SELECTION
> Immobilizer
REMOTE
VEHICLE SELECTION
> TYPE 1
TYPE 2
ECU IDENTIFICATION
LEXUS TYPE 1
PRESS ENTER KEY
SWITCH IGNITION ON
PRESS ENTER KEY
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
> SPECIAL FUNCTIONS
DIAGNOSTIC MENU
RESET Immobilizer
ADD MASTER KEY
ADD VALET KEY
> ERASE KEYS
ERASE KEYS
WARNING
FOLLOW NEXT SCREENS
QUICKLY & CAREFULLY
PRESS ENTER KEY
ERASE KEYS
SWITCH IGNITION OFF
REMOVE MASTER KEY
WITHIN 10 Sec
TIME ELAPSED: 1 S
NOTE: If you do not have an existing Master key, you must use the “Reset Immobilizer” procedure to Reset
the Immobilizer system. A Valet key will not work as a substitute for a Master Key.
ERASE KEYS
INSERT MASTER KEY
SWITCH IGNITION ON
PRESS ENTER KEY
PLEASE WAIT
TRYING TO COMMUNICATE
ERASE KEYS
PROCEDURE COMPLETE
PRESS ENTER KEY
Note: If you get an Error message screen,
disconnect and remove the key.
Wait 20 seconds and start over.
Insert a Master key that is already registered into the vehicle. Turn the ignition lock to the “ON”
position. The Security Light must be out when the key is in. Connect and follow screens.
ERASE KEYS - TYPE 1
MVP &
TCODE TOYOTA ADVANCED DIAGNOSTICS USA powered
by
MVP &
TCODE ADVANCED DIAGNOSTICS USA
powered
by
PRIUS ‘04-’09
MVP &
TCODE TOYOTA ADVANCED DIAGNOSTICS USA powered
by

541
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
MVP &
TCODE TOYOTA ADVANCED DIAGNOSTICS USA powered
by
TYPE 2
Toyota Immobilizer
Use the KEY LOOK UP GUIDE to determine proper key blanks to use.
There are various aftermarket version of these keys you can use.
When in doubt check with the dealer for the exact part number
for the key.
ALL Toyota TYPE 2 use what the industry refers to as a 4D transponder chip in the keys.
Factory 4D chips can come in two varieties MASTER and VALET.
Factory keys with grey plastic heads have a VALET type & chip cannot be used to perform a
RESET or to introduce more keys into the system with the MVP or T-Code.
How to tell if a programmed key is a MASTER or a VALET?
Valet key- when rst inserted into the ignition lock, the Security Light will stay on for 2 sec-
onds and then stay off.
Master key- when inserted into the ignition lock, the Security Light will not illuminate at all.
TYPE 2 SPECIAL FUNCTIONS:
“QUICK” RESET Immobilizer: (“NEW” Available on Type 2 Immobilizer)
This function allows you to erase all keys and to place the immobilizer in “Auto Learn Mode”
instantly without having to go thru the 16 or 30 minute security delay found on the older regu-
lar Reset. This function is used when the customer has lost all their Master keys.
“REGULAR” RESET Immobilizer: (Old way of resetting with security delay, now replaced
with QUICK RESET) This function allows you to erase all keys and to place the immobilizer
in the “Auto Learn Mode”. This function is used when the customer has lost all their Master
keys and the Quick Reset can’t be used (See Below)
In some cases it maybe necessary to use the old timed access reset because sometimes the
quick reset will only let you program TWO keys and no more than that. (Rare, but possible)
PROGRAM KEY: This function allows you to add a Master key to the car’s immobilizer sys-
tem as long as you have an existing pre-programmed Master key to start with.
ERASE KEYS: This function allows you to erase all keys except the key in the ignition lock
at the time.
MVP &
TCODE
PRIUS ‘04-’09
ADVANCED DIAGNOSTICS USA
powered
by MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
powered
by

542 Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
VEHICLE SELECTION
> Immobilizer
REMOTE
VEHICLE SELECTION
TYPE 1
> TYPE 2
TYPE 3
TYPE 4
TYPE 5
ECU IDENTIFICATION
TOYOTA/LEXUS TYPE 2
PRESS ENTER KEY
SWITCH IGNITION ON
PRESS ENTER KEY
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
LIVE DATA
ACTUATORS
> SPECIAL FUNCTIONS
DIAGNOSTIC MENU
RESET Immobilizer
PROGRAM KEY
ERASE KEYS
> QUICK RESET Immobilizer
TRYING TO COMMUNICATE
QUICK RESET IMMOBILIZER
This will RESET the immobilizer and place
the system in “AUTO LEARN MODE”
Within just seconds.
WATCH THE SECURITY LIGHT!
Most of the time you will see PROCEDURE COMPLETE message on the tester.
However, sometimes the car does not signal the tester that the immobilizer has been
reset and you may see COMMUNICATION FAILED on the screen.
DO NOT WATCH THE TESTER,
WATCH THE CARS SECURITY LIGHT!
Auto Learn mode is indicated by the steady illumination of the Security Light.
Once you see a solid immo light. Insert each key you want to program - but do not turn
the key ON - only insert and remove after 5 seconds. The vehicle may learn up to 4 keys
before the Auto Learn cycle is shut down.
You can close the cycle early by turning the ignition lock from Off to On and back to Off
6-8 times, very fast, with a Master key. Remove the key and re-insert it and the Security
Lite should be out when there is a programmed key in the ignition.
(Use this method if you have no Master Keys.)
Quick” RESET Immobilizer - TYPE 2
MVP &
TCODE TOYOTA ADVANCED DIAGNOSTICS USA powered
by
RESET Immobilizer
PROCEDURE COMPLETE
PRESS ENTER KEY
RESET Immobilizer
COMMUNICATION FAILED
PRESS ENTER KEY
OR
Both are OK
MVP &
TCODE ADVANCED DIAGNOSTICS USA
powered
by
PRIUS ‘04-’09
MVP &
TCODE TOYOTA ADVANCED DIAGNOSTICS USA powered
by

543
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
VEHICLE SELECTION
> Immobilizer
REMOTE
VEHICLE SELECTION
TYPE 1
> TYPE 2
ECU IDENTIFICATION
TOYOTA/LEXUS TYPE 2
PRESS ENTER KEY
SWITCH IGNITION ON
PRESS ENTER KEY
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
LIVE DATA
ACTUATORS
> SPECIAL FUNCTIONS
DIAGNOSTIC MENU
> RESET Immobilizer
PROGRAM KEY
ERASE KEYS
RESET Immobilizer
GAINING ACCESS
TIME REQUIRED 30:00
TIME ELAPSED 0:28
RESET Immobilizer
PROCEDURE COMPLETE
PRESS ENTER KEY 1
2
Note: This will cause ALL keys to be
erased and the Immobilizer system to
reset itself.
Note: Do not be impatient.
Some vehicles may go over 30 minutes.
If the timer goes over 40 minutes - stop.
Disconnect from the OBD2 port and re-
move the key. Wait 20 sec. and start over.
Note: You must remove the Master key &
Disconnect at this point.
The Immobilizer system is now Reset. If
you insert the correct transponder type
key, the Security Light should remain
steady & illuminated.
The vehicle is now in Auto Learn mode. Auto Learn mode is indicated by the steady
illumination of the Security Light. Insert each key you want to program - but do not
turn the key ON - only insert and remove after 5 seconds. The vehicle
may learn up to 4 keys before the Auto Learn cycle is shut down.
You can close the cycle early by turning the ignition lock from Off to On and back to Off 5
times, very fast, with a Master key. Remove the key and re-insert it and the Security Lite
should be out when there is a programmed key in the ignition.
On this type of vehicle, the Immobilizer computer can tell the difference between a Master
& Valet key by the type of transponder in the key.
Old way of doing a Type 2 Reset, (use only in rare instances, see notes)
“Regular” RESET Immobilizer - TYPE 2
MVP &
TCODE TOYOTA ADVANCED DIAGNOSTICS USA powered
by
The quick reset on the previous page can be used
99% of the time and the old method shown here
is almost NEVER needed. However in some rare
instances the quick reset may only allow TWO keys
to be programmed. In these cases you can still use
the old method with the security delay, after which 3
or 4 keys can be introduced successfully.
MVP &
TCODE
PRIUS ‘04-’09
ADVANCED DIAGNOSTICS USA
powered
by MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
powered
by

544 Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
VEHICLE SELECTION
> Immobilizer
REMOTE
VEHICLE SELECTION
TYPE 1
> TYPE 2
ECU IDENTIFICATION
TOYOTA/LEXUS TYPE 2
PRESS ENTER KEY
SWITCH IGNITION ON
PRESS ENTER KEY
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
LIVE DATA
ACTUATORS
> SPECIAL FUNCTIONS
DIAGNOSTIC MENU
RESET Immobilizer
> PROGRAM KEY
ERASE KEYS
PROGRAM KEY
SWITCH IGNITION OFF
REMOVE KEY
INSERT KEY
SWITCH IGNITION ON
WITHIN 120 Sec
TIME ELAPSED: 0 S
PRESS ENTER KEY
PROGRAM KEY
SWITCH IGNITION OFF
REMOVE KEY
WITHIN 20 Sec
TIME ELAPSED: 0 S
PRESS ENTER KEY
NOTE: If you do not have an existing Master key, you must use the “Reset Immobilizer” procedure to Reset
the Immobilizer system. A Valet key will not work as a substitute for a Master Key.
PROGRAM KEY
INSERT NEW KEY
LEAVE IGNITION OFF
WITHIN 10 Sec
TIME ELAPSED: 0 S
PRESS ENTER KEY
PROGRAM KEY
PLEASE WAIT
TIME ELAPSED: 2 S
PROGRAM KEY
PROCEDURE COMPLETE
TIME ELAPSED: 59 S
PRESS ENTER KEY
Note: This usually takes about 60 seconds.
If the timer goes past 120 seconds, stop.
The key is most likely now programmed.
Disconnect & try key.
Note: You must remove the Master
key & then press enter.
Note: You must insert the New key
but do not turn it.
Press Enter when done.
Insert a Master key that is already registered into the vehicle. Turn the ignition lock to the “ON”
position. The Security Light must be out when the key is in. Connect and follow screens.
ADD MASTER or VALET KEY - TYPE 2
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
powered
by
MVP &
TCODE ADVANCED DIAGNOSTICS USA
powered
by
PRIUS ‘04-’09
MVP &
TCODE TOYOTA ADVANCED DIAGNOSTICS USA powered
by

545
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
VEHICLE SELECTION
> Immobilizer
REMOTE
VEHICLE SELECTION
TYPE 1
> TYPE 2
ECU IDENTIFICATION
LEXUS TYPE 1
PRESS ENTER KEY
SWITCH IGNITION ON
PRESS ENTER KEY
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
LIVE DATA
ACTUATORS
> SPECIAL FUNCTIONS
DIAGNOSTIC MENU
RESET Immobilizer
PROGRAM KEY
> ERASE KEYS
ERASE KEYS
SWITCH IGNITION OFF
REMOVE KEY
INSERT KEY
SWITCH IGNITION ON
WITHIN 120 Sec
TIME ELAPSED: 0 S
PRESS ENTER KEY
PLEASE WAIT
TRYING TO COMMUNICATE
NOTE: If you do not have an existing Master key, you must use the “Reset Immobilizer” procedure to Reset
the Immobilizer system. A Valet key will not work as a substitute for a Master Key.
ERASE KEYS
SWITCH IGNITION OFF
REMOVE KEY
WITHIN 10 Sec
TIME ELAPSED: 0 S
ERASE KEYS
PROCEDURE COMPLETE
PRESS ENTER KEY
Note: If you get an Error
message screen, disconnect and
remove the key.
Wait 20 seconds and start over.
Insert a Master key that is already registered into the vehicle. Turn the ignition lock to the “ON”
position. The Security Light must be out when the key is in. Connect and follow screens.
ERASE KEYS - TYPE 2
MVP &
TCODE TOYOTA ADVANCED DIAGNOSTICS USA powered
by
MVP &
TCODE
PRIUS ‘04-’09
ADVANCED DIAGNOSTICS USA
powered
by MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
powered
by

546 Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
MVP - TCODE - PRO
Powered by ADVANCED DIAGNOSTICS USA
(Optional Software on all TCode Units.)
Toyota
Key Programming
TOYOTA 2007
ADS-150

547
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
TOYOTA 2007
Types of Keys & Remote Head Keys in Use
Toyota Factory Key
Non-Remote Head Key
89785-08020 or 89785-60160
Toyota Factory Remote Head Key
2007 Camry
89070-33881
Use the KEY LOOK UP GUIDE to determine proper key blanks to use.
There are various aftermarket version of these keys you can use.
When in doubt check with the dealer for the exact part number
of the key or remote.
A “DOT” on the key blade
usually indicates the key has
a Texas Instruments 4D type
chip inside
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
powered
by

548 Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
TYPE 4
Toyota Immobilizer
Use the KEY LOOK UP GUIDE to determine proper key blanks to use.
There are various aftermarket version of these keys you can use.
When in doubt check with the dealer for the exact part number
for the key.
ALL Toyota TYPE 4 use what the industry refers to as a 4D transponder chip in the keys.
Factory 4D chips can come in two varieties MASTER and VALET.
Factory keys with grey plastic heads have a VALET type & chip cannot be used to perform a
RESET or to introduce more keys into the system with the MVP or T-Code.
How to tell if a programmed key is a MASTER or a VALET?
Valet key- when rst inserted into the ignition lock, the Security Light will stay on for 2 sec-
onds and then stay off.
Master key- when inserted into the ignition lock, the Security Light will not illuminate at all.
TYPE 4 SPECIAL FUNCTIONS:
“QUICK” RESET Immobilizer: (“NEW” Available on Type 4 Immobilizer)
This function allows you to erase all keys and to place the immobilizer in “Auto Learn Mode”
instantly without having to go thru the 16 or 30 minute security delay found on the older regu-
lar Reset. This function is used when the customer has lost all their Master keys.
“Regular” RESET Immobilizer: (Old way of resetting with security delay, now replaced with
QUICK RESET) This function allows you to erase all keys and to place the immobilizer in the
“Auto Learn Mode”. This function is used when the customer has lost all their Master keys
and the Quick Reset can’t be used (See Below)
In some cases it maybe necessary to use the old timed access reset because sometimes the
quick reset will only let you program TWO keys and no more than that. (Rare, but possible)
RESET ECU: This procedure needs to be completed after RESET Immobiliser to re sync the
cars immobilizer and ECU. (Not needed after Quick Reset as Quick Reset includes an ECU)
PROGRAM KEY: This function allows you to add a Master key to the car’s immobilizer sys-
tem as long as you have an existing pre-programmed Master key to start with.
ERASE KEYS: This function allows you to erase all keys except the master key in the igni-
tion lock at the time.
MVP &
TCODE TOYOTA ADVANCED DIAGNOSTICS USA powered
by

549
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
VEHICLE SELECTION
> Immobilizer
REMOTE
VEHICLE SELECTION
TYPE 1
TYPE 2
TYPE 3
> TYPE 4
TYPE 5
ECU IDENTIFICATION
TOYOTA/LEXUS TYPE 4
PRESS ENTER KEY
SWITCH IGNITION ON
PRESS ENTER KEY
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
LIVE DATA
ACTUATORS
> SPECIAL FUNCTIONS
DIAGNOSTIC MENU
RESET Immobilizer
PROGRAM KEY
ERASE KEYS
> QUICK RESET Immobilizer
TRYING TO COMMUNICATE
QUICK RESET IMMOBILIZER
This will RESET the immobilizer and place
the system in “AUTO LEARN MODE”
Within just seconds. On Type 4 this also
performs the ECU Reset.
WATCH THE SECURITY LIGHT!
Most of the time you will see PROCEDURE COMPLETE message on the tester.
However, sometimes the car does not signal the tester that the immobilizer has been
reset and you may see COMMUNICATION FAILED on the screen.
DO NOT WATCH THE TESTER,
WATCH THE CARS SECURITY LIGHT!
Auto Learn mode is indicated by the steady illumination of the Security Light.
Once you see a solid immo light. Insert each key you want to program - but do not turn
the key ON - only insert and remove after 5 seconds. The vehicle may learn up to 4 keys
before the Auto Learn cycle is shut down.
You can close the cycle early by turning the ignition lock from Off to On and back to Off
6-8 times, very fast, with a Master key. Remove the key and re-insert it and the Security
Lite should be out when there is a programmed key in the ignition.
(Use this method if you have no Master Keys.)
QUICK RESET Immobilizer - TYPE 4
RESET Immobilizer
PROCEDURE COMPLETE
PRESS ENTER KEY
RESET Immobilizer
COMMUNICATION FAILED
PRESS ENTER KEY
OR
Both are OK
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
powered
by

550 Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
VEHICLE SELECTION
> Immobilizer
REMOTE
PROXIMITY
VEHICLE SELECTION
TYPE 1
TYPE 2
TYPE 3
> TYPE 4
ECU IDENTIFICATION
TOYOTA/LEXUS TYPE 4
PRESS ENTER KEY
SWITCH IGNITION ON
PRESS ENTER KEY
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
LIVE DATA
ACTUATORS
> SPECIAL FUNCTIONS
DIAGNOSTIC MENU
> RESET Immobilizer
PROGRAM KEY
ERASE KEYS
RESET ECU
RESET Immobilizer
GAINING ACCESS
TIME REQUIRED 30:00
TIME ELAPSED 0:28
RESET Immobilizer
PROCEDURE COMPLETE
PRESS ENTER KEY
STANDARD RESET Immobilizer - TYPE 4
DIAGNOSTIC MENU
RESET Immobilizer
PROGRAM KEY
ERASE KEYS
> RESET ECU
RESET ECU
PROCEDURE COMPLETE
PRESS ENTER KEY
Now you must
RESET the ECU.
Old way of doing a Type 4 Reset, (use only in rare instances, see note)
NOTE: The quick reset on the previous page can be used 99% of the time and the old method shown
here is almost NEVER needed. However in some rare instances the quick reset may only allow TWO
keys to be programmed. In these cases you can still use the old method with the security delay, after
which 3 or 4 keys can be introduced successfully.
Note: You must remove the Master key & Disconnect the tester at this point.
The Immobilizer system is now Reset. The Security Light should remain steady & illuminated.
The vehicle is now in Auto Learn mode. Auto Learn mode is indicated by the steady illumination of the Security Light. Insert each key
you want to program - but do not turn the key on - only insert and remove after 4 seconds. The vehicle may learn up to 4 keys before
the Auto Learn cycle is shut down.
You can close the cycle early by turning the ignition lock from Off to On and back to Off 6 times, very fast, with a Master key.
Remove the key and re-insert it and the Security should be out when there is a programmed in the ignition.
MVP &
TCODE TOYOTA ADVANCED DIAGNOSTICS USA powered
by

551
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
(Use this method if you have at least 1 Master Key.)
PROGRAM KEYS - TYPE 4
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
VEHICLE SELECTION
> Immobilizer
REMOTE
PROXIMITY
ECU IDENTIFICATION
TOYOTA/LEXUS TYPE X
PRESS ENTER KEY
SWITCH IGNITION ON
PRESS ENTER KEY
DIAGNOSTIC MENU
ECU IDENTIFICATION
FAULT CODES
LIVE DATA
ACTUATORS
> SPECIAL FUNCTIONS
DIAGNOSTIC MENU
RESET Immobilizer
> PROGRAM KEY
ERASE KEYS
RESET ECU
PROGRAM KEY
SWITCH IGNITION OFF
REMOVE KEY
INSERT KEY
SWITCH IGNITION ON
WITHIN 120 Sec
TIME ELAPSED: 0 S
PRESS ENTER KEY
PROGRAM KEY
SWITCH IGNITION OFF
REMOVE KEY
WITHIN 20 Sec
TIME ELAPSED: 0 S
PRESS ENTER KEY
NOTE: If you do not have an existing Master key you must use the “Reset Immobilizer” procedure to Reset
the Immobilizer system. A Valet key will not work as a substitute for a Master Key.
Note: You must remove the
Master key & then press
enter.
PROGRAM KEY
INSERT NEW KEY
LEAVE IGNITION OFF
WITHIN 10 Sec
TIME ELAPSED: 0 S
PRESS ENTER KEY
PROGRAM KEY
PLEASE WAIT
TIME ELAPSED: 2 S
PROGRAM KEY
PROCEDURE COMPLETE
TIME ELAPSED: 59 S
PRESS ENTER KEY
Note: This usually takes about 60 seconds.
If the timer goes past 120 seconds, stop.
The key is most likely now programmed.
Disconnect & try key.
Note: You must insert the New key,
but Do Not turn it.
Press Enter when done.
VEHICLE SELECTION
TYPE 1
TYPE 2
TYPE 3
> TYPE 4
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
powered
by

552 Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
Toyota Remote
GRID INDEX
- Only the models listed are supported -
TOYOTA
MODELS YEARS SYSTEM TYPE S/W T-CODE
4-RUNNER 2007-2013 REMOTE 2 ADS-125
AVALON 2010-2013 REMOTE 2 ADS-125
CAMRY 2007-2013 REMOTE 4 ADS-150
COROLLA Mid 2010-2013 REMOTE 4 ADS-150
FJ CRUISER 2010-2012 REMOTE 4 ADS-150
HIGHLANDER 2005-2006 REMOTE 4 ADS-150
LAND CRUISER 2003-2013 REMOTE 2 ADS-125
RAV-4 2007-2013 REMOTE 4 ADS-150
SEQUOIA 2003-2013 REMOTE 4 ADS-125
SIENNA 2010-2013 REMOTE 4 ADS-150
TUNDRA 2003 REMOTE 2 ADS-125
TUNDRA 2007-2013 REMOTE 4 ADS-150
VENZA 2010-2013 REMOTE 4 ADS-150
MVP &
TCODE TOYOTA ADVANCED DIAGNOSTICS USA powered
by
TOYOTA TYPE 4 IMMOBILIZER
Troubleshooting:
Problem: After a Reset, the car starts and runs but the theft light blinks.
Solution: The car is still in “learn mode” close the learning cycle by turning the ignition ON/OFF quickly at least
6-8 times until the light goes out.
Problem: Program key goes all the way thru to a successful conclusion with no errors but the car cranks and
does not start.
Solution: Barring any other problems (low fuel, failed components etc) the car key memory may be full. Meaning
8 keys are already programmed and no more can be added. Use ERASE KEYS with a MASTER KEY and this
will ERASE all keys except the 1 Master Key used. Now go back and use PROGRAM KEY to add any other keys
you want to program.

553
Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
VEHICLE SELECTION
MITSUBISHI
NISSAN
SUZUKI
> TOYOTA
V.W./AUDI GROUP
VEHICLE SELECTION
Immobilizer
> REMOTE
PROXIMITY
ECU IDENTIFICATION
TOYOTA TYPE 4
PRESS ENTER KEY
SWITCH IGNITION ON
PRESS ENTER KEY
DIAGNOSTIC MENU
ECU IDENTIFICATION
> SPECIAL FUNCTIONS
DIAGNOSTIC MENU
ERASE REMOTES
> PROGRAM REMOTE
PROGRAM REMOTE
PRESS LOCK & UNLOCK
TOGETHER FOR 4 Sec.
PRESS UNLOCK BUTTON
FOR 1 SEC
BACK’ TO EXIT
PROGRAM REMOTE
PROCEDURE COMPLETE
PRESS ENTER KEY
Note: Press the Lock & Unlock
buttons together for 4 seconds
and quickly press Unlock button
for 1 second. You must be fast
on the button operation.
PRESS the BACK
BUTTON to COMPLETE
THE PROGRAMMING.
PROGRAM REMOTE - TYPE 4
PROGRAM REMOTE
SYSTEM WILL BEEP
WHEN COMPLETE
PRESS ENTER KEY
(Use this method to program the Remote portion of remote head keys
And also for programming separate remotes)
The RKE program separate from
the transponder on LEXUS &
TOYOTA remote head keys
VEHICLE SELECTION
TYPE 1
> TYPE 2
TYPE 3
> TYPE 4
Use the Grid earlier in this sec-
tion for proper system selection.
MVP &
TCODE
TOYOTA
ADVANCED DIAGNOSTICS USA
powered
by

554 Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
Examples of different Types of PROX
Toyota Avalon PROX
89904-07030
Toyota Camry PROX
89904-06041
Lexus ES / GS / IS PROX
89904-30270
Always check with the dealer for the exact part number of Prox to
use on the vehicle you are working on.
These are just a few examples shown for 2007 models. For later
years there are quite a few different part numbers some inter-
changeable and some not!
TOYOTA 2007
Used Toyota/Lexus Proximity key warning!
Prox keys that are not BRAND NEW cannot be simply ADDED.
There is a work around trick that will usually allow you to program in an already used Prox.
1. Perform an Immobilizer reset introducing the used key rst.
2. Once you have the used key programmed and working use PROGRAM PROX
to add back in the original working Prox key(s).
MVP users take note: The above method may not always work 100%.
Brand new keys from a reputable dealer is what we recommend.
These program in 100% without issue.
Cross Interference:
It has been our experience that on occasion there can be cross signal interference when 2 or more Prox remotes are in the
vehicle at the same time. During Programming keep only one Prox remote in the car at a time because of this.
Weak Prox Batteries:
Also, when using NEW Prox remotes if they get a failure it can be because the battery in the Prox is slightly weak from
sitting around in the parts dept. and may not program in until the Prox battery is changed.
MVP &
TCODE TOYOTA ADVANCED DIAGNOSTICS USA powered
by