Advanced Technology Video FD650WDR User manual

i
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
DO NOT INSERT ANY METALLIC OBJECT THROUGH VENTILATION GRILLS.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle,
is intended to alert the user to the presence of uninsulated ''dangerous
voltage'' within the product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the product.
PRECAUTIONS
WARNING : TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER(OR BACK).
NO USER-SERVICABLE PARTS INSIDE.
REFFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
Safety
Should any liquid or solid object fall into the cabinet,
unplug the unit and have it checked by
qualified personnel before operating it any further.
Unplug the unit from the wall outlet if it is not going to
be used for several days or more.
To disconnect the cord, pull it out by the plug. Neve
r
pull the cord itself.
A
llow adequate air circulation to prevent internal heat
build-up. Do not place the unit on soft surfaces (rugs,
carpets, sofas, etc.) or near materials (curtains,
draperies) that may block the ventilation holes.
Height and vertical linearity controls located on the
rear panel are for special adjustments by qualified
personnel only.
Installation
Do not install the unit in an extremely hot or humid place
or in a place subject to excessive dust, mechanical
vibration.
The unit is not designed to be waterproof.
Exposure to rain or water may damage the unit.
Cleaning
Clean the unit with a slightly damp soft cloth.
Use a mild household detergent. Never use strong
solvents such as thinner or benzine as they might
damage the finish of the unit.
Retain the original carton and packing materials for safe
transport of this unit in the future.

ii
FCC COMPLIANCE STATEMENT
CE COMPLIANCE STATEMENT
INFORMATION TO THE USER:THIS EQUIPMENT HAS BEEN TESTED
AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE,
PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED
TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL
INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL
ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE
RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN
ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS.
OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO
CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE
REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.
CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED
BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S
AUTHORITY TO OPERATE THE EQUIPMENT.
THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.
CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST CONFORME À LA NORME
NMB-003 DU CANADA.
WARNING: This is a Class A product. In a domestic environment this product
may cause radio interference in which case the user may be required to take
adequate measures.

iii
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the m
anufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plu
g. A polarized plug has two blades with one wider than the other. A gro
unding type plug has two blades and a third grounding prong. The wid
e blade or the third prong are provided for your safety. If the provided p
lug does not fit into your outlet, consult an electrician for replacement o
f the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from th
e apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use cau
tion when moving the cart/apparatus combination to avoid injury from ti
p-over.
13. Unplug this apparatus during lightning storms or when unused for long
periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-su
pply cord or plug is damaged, liquid has been moisture, does not oper
ate normally, or has been dropped.
15. CAUTION – THESE SERVICING INSTRUCTIONS ARE FOR USE B
Y QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RIS
K OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OT
HER THAN THAT CONTAINED IN THE OPERATING INSTRUCTION
S UNLESS YOU QRE QUALIFIED TO DO SO.
16. Use Certified/Listed Class 2 power source only.

iv
CONTENTS OF PACKAGE
The package contains the following
Camera in Housing ------------------------------------------------------------------1
Instruction Manual (This Document) --------------------------------------------1
Accessory Kit for Installing ---------------------------------------------------------1
Drilling guide label -------------------------------------------------------------------1
TABLE OF CONTENTS
INTRODUCTION ---------------------------------------------------------------------------------------1
CAMERA CONNECTIONS --------------------------------------------------------------------------2
INSTALLATION-----------------------------------------------------------------------------------------3
LENS ADJUSTMENT ---------------------------------------------------------------------------------5
DC AUTO IRIS LENS --------------------------------------------------------------------------------- 5
CAMERA ADJUSTMENT ----------------------------------------------------------------------------6
EXTERNAL DIMENSION ----------------------------------------------------------------------------13
SPECIFICATIONS -------------------------------------------------------------------------------------14

1
INTRODUCTION
The camera provided high-quality image using SONY Wide Dynamic 1/3” Super-HADII
PS 960H CCD and digital signal processing LSIs.
Features:
•1/3” Super-HADII PS 960H CCD
•Super high-resolution of 650TV lines
•0.4 lux(Color), 0.04 lux(B/W), 0.001 lux(Slow-Shutter) @ F1.4 Sensitivity
•Auto Electronic Shutter [1/60(1/50) ~ 1/100,000] and manual electronic shutter
modes [1/60(1/50) ~ 1/10,000]
•On Screen Display (OSD)
•Auto and Manual white balance modes
•Support Line-Lock external synchronization
•Digital PTZ
•Digital Effect (H/V reverse, 180 degree rotate, inverse, freeze)
•2D-NR, 3D-NR (DNR Demo)
•Back Light Compensation
•Back Light Masking (MAX. 15 area)
•Excessive High-Light Compensation
•Wide Dynamic Range (~x512)
•Various Detection Method (zone detection, motion trace, face trace, mine area,
absent detection, cross object counting, entrance counting)
•Day & Night(Auto, Manual, External, Filter delay)
•Various Alarm Method (Period, Snooze, Polarity Select)
•Privacy Mask or Mosaic (MAX. 15 area/4-point polygonal/transparency)
•Scene Change Detection
•Sens-Up (~x32)
•White Pixel Remove
•Frame Control (Auto, 1~7 sec)
•System Lock (4-Digit password)
•RS-485 Remote camera control
•F1.4 D&N DC iris vari-focal lens
•Operates in 12VDC or 24VAC
•User Certified / Listed Class 2 power source only

2
CAMERA CONNECTIONS
Connection Cable Description
COLOR Description
RED AC24V/DC12V
WHITE AC24V/DC12V
ORANGE ADKEY
BROWN GND
BLUE RS485(-)
GREEN RS485(+)
YELLOW ALARM OUT
GRAY DN EXT-IN
BLACK&WHITE DN EXT-OUT
BLACK GND
SKY BLUE UTP+(optional)
PINK UTP- (optional)
1) External Day/Night Control : To select Day/Night mode using external equipment,
by connecting control lines to the appropriate terminals.
¾DAY&NIGHT OUTPUT (Black&White)
Is the camera function that can turn on an external IR LED Lamp by detecting
the sensitivity on the AGC level when the D&N mode is set "AUTO" on the
OSD menu of the camera
¾DAY&NIGHT EXTERNAL INPUT (Gray)
Is the camera function that can be switched to DAY Mode or NIGHT mode by
receiving the D&N on/off signal from external light sensor or IR LED LAMP.
This needs the D&N Mode to be set to "External" on the OSD menu of the
camera to work
2) Alarm Out
¾Motion detection signals are output through this port. (YELLOW AND GND)
¾Active state is configurable.
3) Power Input Terminal
¾RED & WHITE : DC Power is recommended to use the DC power supply that
can support inrush current over 0.75A
4) Camera Control
¾GREEN : RS 485+
¾BLUE : RS 485-
5) UTP (optional)
¾Video signal through out the UTP Cable (SKY BLUE(+) & PINK(-) )
DAY&NIGHT INPUTGra
y
GND
Black Close contact : NIGHT
Open contact : DAY
●
●
GNDBlack
DAY&NIG
Black&White ●5V/10mA : IR LED ON (NIGHT)
●0V : IR LED OFF (DAY)

3
INSTALLATION
1. Make mounting holes and cable hole in the place (ceiling or wall) to which this
dome camera is installed using the Drilling guide label.
2. To remove dome cover, turn the dome body counterclockwise until locators reach
end of travel and pull off. Push the liner on the sides where the patterns are put in
the teeth of a comb and pull it out.

4
*Label is attached at the bottom.
3. Attach the housing to the ceiling using suitable fasteners, M6x35 tapping screws
are supplied only use if they are suitable. Turn the housing to right direction
about 16 degrees to lock in place.
4. The assembly of the dome body and liner is in reverse order of disassembly.
Finally, lock dome body with locking screw (M3X5) from the accessory kit.

5
LENS ADJUSTMENT
DC AUTO IRIS LENS
2.6-6mm 4-9mm 2.8~12mm 6-50mm
Image Size 1/3” CCD 1/3" CCD 1/3" CCD 1/3" CCD
Focal Length 2.6-6.0mm ±5% 4.0-9.0mm ±5% 2.8-12mm ±5% 6.0-50mm ±5%
Aperture
Ratio 1 : 1.6 ±5% 1 : 1.6 ±5% 1 : 1.4 ±5% 1 : 1.6 ±6.9%
Angular
Field of View
(Degree)
DIAGONAL
2.6mm : 134.6
6mm : 59.2
DIAGONAL
4mm : 92.4
9mm : 39.2
DIAGONAL
2.8mm : 119.9
12mm : 28.8
DIAGONAL
6mm : 58.6
50mm : 7.1
Field of view: Adjust setting
from Telephoto (T) to wide (W)
field of View.
Focus: Adjust lens focus from
near (N) to infinity.

6
CAMERA ADJUSTMENT
<White Balance>
1) Auto(Auto White Balance) : AWB mode (1800ºK ~10500ºK)
2) Push/Hold : Push&Hold Mode.
¾To find the Optimal setting for the current luminance environment in this mode,
set the direction towards a sheet of white paper and select Hold and press enter
button. If the environment changes, readjust it.
3) CRS Mode(Color Rolling Suppression) : Decrease color rolling effect.
¾This operation take some time about 10 seconds and user can stop this
operation by pressing enter button.
¾When CRS Mode is on, color tone can be weak.
4) Outdoor : Set color temperature to outdoor (6300ºK)
5) Indoor : Set color temperature to indoor (3200ºK)
6) FL(Fluorescent Light) : Set color temperature to fluorescent light fixed gain.
7) User(User Set White Balance) : Adjust red or blue gain.
¾R(R-GAIN):Adjust R-GAIN value (0-255)
¾B(B-GAIN):Adjust B-GAIN value (0-255)
<Auto Exposure>
1) SHT(s)(Electronic Shutter) : Select Shutter mode.
¾Auto(1/60(1/50) ~ 1/100,000 Auto run, Manual 8 step from 1/60(1/50) ~1/10,000).
2) FLC(Flicker-less) : Flicker-less On/Off.
3) AGC(Auto Gain Control) : AGC Gain(Off, Low, Middle, High)
4) Sens-Up(Slow Shutter) : Maximum Slow-Shutter select. (x2-x32 and Off)
5) Offset Add : Force the picture to turn up at low luminance environment.
<BLC/WDR>
1) Normal AE : BLC/WDR function off.
2) WDR(Wide Dynamic Range) : Wide dynamic range mode on.
3) EHLC(Excessive High Light Compensation) : EHLC mode on.
¾excessive lighting compensation is performed when the weighting on the
high-brightness side is increased.
4) Auto(Auto Weighting BLC) : Auto weighting BLC on.
5) Spot(User Setting BLC area) : Spot metering mode on.
¾Posi : OSD mode to adjust the position of the spot metering area.
¾Size : OSD mode to adjust the size of the spot metering area.
6) Zone(Preset BLC area) : Fixed metering area mode. (1-9).
<Mask>
1) Mask: Select mask area(1-15).
2) Func: Select mask function.(Privacy, BLM, Both, Off).
¾Privacy : Area to screen on the display.
¾BLM : Back Light Mask.
Selected BL Mask area that will be except of the auto exposure

7
If there is a high light installed in a limited environment such as an
apartment parking garage or gas station entrance, removing the high light
makes it possible to view car license plates efficiently.
¾Both : Privacy function and BLM function on.
¾Off : Function off.
3) Edit : Mask area edit.
¾Edit mode take effect during Func not Off.
Size : adjust the size of the Privacy and BLM mask area.
Posi : adjust the position of the Privacy and BLM mask area.
Tilt : adjust tilting of Privacy and BLM mask area.
Color: Select Privacy and BLM mask (0-14).
Transparency: Select Privacy mask transparency (Default 3/0-3).
Mosaic: Select Privacy and BLM mask mosaic On/Off
Adj. Mosaic: Adjust Privacy and BLM mask mosaic level (0-31).
<Detection>
1) Func : Detection function selection.
¾OFF : Detection function off.
¾Zone : Area motion detection mode.
Zone : Select Motion detection zone (Zone1-4).
Func : Select Motion detection on/off.
Size : Press Enter button to adjust the size of the Motion detection area.
Posi : Press Enter button to adjust the position of the Motion detection
area.
Link Zoom : Select Motion detection with D-PTZ function that
On/Off.( When the motion triggered in the area, zoom and move to the
area with D-PTZ.)
¾Motion Trace : Motion trace mode on.
Tracks an object through a scene and generates an alarm.
¾Face Trace : Face Trace mode on.
Tracks face through a scene and generate an alarm.
Sens Down : lower value is more widen the scope to judge face. (0~127)
Min Size : Minimum face size configuration (0 : minimum face size is to
none)
The result of face trace can be inaccuracy.
¾Mine : By this function, User can draw motion detection area with free dotting
Set Mine : Press the Enter button to Set Mine mode.
< > : Move : Mine Zone move using the Left and Right buttons.
UP:Set : Mine Zone setting using the Up button.
DN:Clr : Mine Zone clear using the Down buttons.
ENT:End : Press the Enter button to set Mine mode end.
Clr All : Press the Enter button to set Mine area clear.
Display : Select Mine Display On/Off.

8
¾Absent : Press the Enter button to Absent detection mode. Detect object
appeared or removed the scene
Sens Down : Adjust sensitivity of Absent check(0-255).
In low luminance environment, the accuracy is down of the result.
Because object color is effect to auto exposure, the accuracy is down of the result
If the object is too big, the accuracy is down of the result.
¾Cross : Cross counting mode
Zone : Select Cross Zone using the Left and Right buttons (Zone 1, Zone
2).
Size : Adjust the size of the Cross zone.
Posi : Adjust the position of the Cross zone.
Direction : Select Cross Direction.
Alarm Cnt : Set alarm out cross count. Alarm count number is delaying
number before output alarm.
Reset Cnt : Cross count reset.
If object is passing so fast through the two area, counting is not operating. In this case,
adjust to expand space between two area or decrease size of area.
If passing object is too long, counting result can be inaccuracy. In this case, adjust to
expand space between two area or adjust to decrease size of area.
If two object passing the area in the same time, the results can be inaccuracy.
¾Entrance : Entrance counting mode. The object move in through the entrance,
counting number increases
Size : Press Enter button adjust the size of the Entrance zone.
Posi : Press Enter button adjust the Position of the Entrance zone.
Alarm Cnt : Set alarm out entrance count. Alarm count number is
delaying number before output alarm.
Reset Cnt : Entrance count reset.
2) Sens Down : Adjust to Motion Sensitivity using left/right Buttons.

9
Crossing object is not considered. / Several objects will not be detected.
If the distance is increases between the camera and entrance, the result can be
inaccuracy.
<Picture/DNR>
1) Sharpness : Adjust sharpness of outlines (0~15)
2) Resolution : Select high resolution mode (Low/Mid/High)
3) 2D-NR : Select 2D noise reduction level (0~6)
¾2D-NR : Noise reduction on a frame
4) 3D-NR : Select 3D noise reduction level (0~31)
¾3D-NR : Noise reduction through the several frame
5) DNR Demo : Select DNR Demo Display On/Off using the Left and Right Buttons
None DNR Effect
Display
DNR Applied
Display
<Effect/Special>
1) d-Effect(Digital Effect) : Select digital Flip/Rotate state (Off/Rotation/Mirror/V Flip )
2) Nega : Select negative color state(on/off)
3) d-PTZ (Digital Pan, Tilt, Zoom) : Adjust d-PTZ.
¾Func : Press the Enter button to turn digital zoom on/off.
¾Zoom : Use the Left and Right buttons adjust to digital zoom(0-255).
¾Pan&Tilt : Press the Enter button to access the Pan&Tilt.
Use the Left and Right buttons adjust to digital pan
Use the Up and Down buttons adjust to digital tilt
Press the Enter button to exit.
¾PT Reset(Pan & Tilt Reset) : Press the Enter button to reset digital pan and tilt.
4) Freeze : Select the still mode on/off
5) Frame Control: Select term of refresh rate for output video. This function is useful to
reduce the recording to data storage.
¾Func : Select frame control mode to ON/OFF, and Auto.
Several Object
Crossing Object
Camera Installed at the ceiling
Crossing object is none
One object is passing.
The distance is too long

10
Auto mode : When motion is not detected, output video is being refresh
in configured interval. And when the motion is detected, output video is
switched to real time video.
ON : Always refresh in configured interval.
OFF : Always real time video.
¾Renewal(sec) : Select an interval between two frame.
When object start moving, The output video possible to cut a little time.
6) ScnChg/Unfoc : Select scene change/unfocus detection On/Off .
¾Inform that whether scene have been changed or not. Detect breaking or
changing in the watching scene (Spray, Screen Camera, Changing Scene…)
¾This function is linked with alarm out
In low luminance environment, the accuracy is down of the result.
In very low luminance environment, operation is not be performed.
It is not be performed when moving object is exist.
<System Setup>
1) Cam Info : Camera basic information display
¾Cam ID/Baud rate/Protocol/Firmware Ver./CCD Type/Lens Type
2) General Setup
¾System Lock : Configuration Lock.
When system lock is set to “Lock”, User must to input 4-character
password to enter OSD menu.
Default password is “0000”.
¾Change PID : Change the administrator’s password
Move cursor with OSD Key and Press Enter to input the character.
¾Comm(RS 485 Communication) : Press the Enter button to access the Comm.
Cam ID : Select the camera ID (001 - 255).
Baud Rate : Select serial communication speed (2400/4800/9600/19200).
Protocol : RS-485 protocol. (COMMAND/FASTRAX/PELCO-D/Pelco-D)

11
A. Title
B. Delete character
C. Character table
D. Command line
- Clear : Clear Title
- Cancel: Cancel editing
- Accept: Save Title
¾Title : Edit camera title.
¾Display : Display item select.
Cam ID : Camera ID display On/Off.
Title : Title display On/Off.
¾Alarm .
Period : Alarm out period (5sec/10sec/20sec/30sec/1min/5min/Cont.)
Snooze : Alarm out snooze(Off/5sec/10sec/20sec/30sec/1min/5min)
Active pol : Alarm output active state configuration. (Low, High)
¾System Init
Cancel : Back to General Setup Menu.
Confirm : Initialize all data. (Factory Default)
3) Lens
¾Iris : DC, Video, Manual Lens selected Iris : adjust AE Speed
DC lens and video lens can adjust AE Speed
¾Normal AE Ref (Auto Exposure Reference Level) : Press the Enter button to
access the AE Ref.
Ref Lvl : Adjust AE base reference level.
¾WDR Ref : Press the Enter button to access the WDR Ref.
Ref Lvl : Adjust the WDR long-time control Base Reference Level.
4) LLC(Line Lock Control) : Press the Enter button to access the Line Lock mode.
¾Func : Select Line Lock function On/Off using the Left and Right buttons.
¾Phase : Adjust Line Lock sync phase using the Left and Right buttons. (0~100)
Title Site_0
☞< > ENT:Del
Clear Cancel Accept
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
-. 0123456789
A
B
C
D

12
Activate only AC power inputted.
5) White Pixel
¾Det Exe : Press Enter button to turn White Pixel Compensation mode Start.
ENT to Adj : Press Enter button to start White Pixel Compensation start.
Proc : Process to find white pixel.
Done : Process ended
¾Det Count : Result of white pixel detection.
¾Func : Select erasing white pixel function On/Off using the Left and Right buttons.
¾Det Level : Select the judgment level of white pixel using the Left and Right
buttons (1~16)
¾Det View : Select display of detected white pixel.
6) Day/Night
¾Mode : Select D&N mode.
Auto : Filter operates automatically according to brightness.
Day : The camera outputs the video image only in color.
Night : The camera outputs the video image only in black and white.
Ext : This menu automatically converts the COLOR Mode into the B/W
Mode or vice versa depending on illumination with an external sensor.
¾Night Mode : Select B/W Burst On/Off
¾Delay(s) : Adjust the working time of the filter when D&N mode is Auto (1-60 sec).
¾D>N Level : Select switching level Day to Night when D&N mode is Auto (0-15).
¾N>D Level : Select switching level Night to Color when D&N mode is Auto (0-15).
<Bottom Line Menus>
When user entered in main menu and sub-menus, following menus will be appeared.
I. Main Manu (menu in bottom lines)
A. Exit : Save & Exit.
B. Load : Load Default Value.
II. Sub Menu (menu in bottom lines)
A. Return : Return to previous menu.
B. Exit : Save & Exit
1) Exit Menu
¾Save&Exit : Current environment values save.
¾Exit : Disappear menu osd.
2) Load Default Setup
¾Yes : Load default to current configuration. and return to previous menu.
¾No : No operation, and return to previous menu.

13
EXTERNAL DIMENSION
Window Size
0.1 in. (2.5mm thick),
impact-resistant P.C (LEXAN)
3.93 in. (10cm) diameter
Cable Entry One 1" opening holes
Weight – Unit:
Shipping:
0.88 lb. (400 g)
1.41 lb. (640 kg)
Unit: mm
145.6
100 (Inner)
11 3
59

14
SPECIFICATIONS
MODEL NTSC PAL
Power source DC 12V / AC 24V ± 10%
Power Power consumption 4.5 Watts
Image sensor 1/3" Super-HADII PS 960H CCD
Total pixels 1028(H)x508(V) 1028(H)x596(V)
Effective pixels 976(H)x494(V) 976(H)x582(v)
Scanning system 2:1 interlace
Scanning frequency 15.734KHz(H)x59.94Hz(V) 15.625KHz(H)x50Hz(V)
Sync. System Internal / Line lock
Resolution 650TVL
Min. illumination 0.4 Lux (COLOR), 0.04 Lux (B/W), 0.001 Lux (Slow-shutter)
Video output 1.0 Vp-p (75 ohm, composite)
S/N ratio 50dB (AGC OFF)
Camera control RS485 (Faxtrax, Pelco D, Pelco P)
Lens 2.8mm~12.0mm/F1.4 D&N DC IRIS Vari-Focal Lens
White Balance Auto / CRS / Push&Hold / Indoor / Outdoor / FL / User
Auto Exposure Auto / Manual Shutter / Flickerless / Low Light Control /
Offset Add
AGC Off / Low / Middle / High
Shutter Speed 1/60-1/10,000
(Auto:1/100,000)
1/50-1/10,000
(Auto:1/100,000)
BLC EHLC / AUTO / SPOT / ZONE/ BLM
Camera Title Alpha Numeric
Display On / Off (Cam ID, Title)
DNR 2DNR, 3D NR :Gain Adjust, DNR Demo
Day & Night Auto / Day / Night / Ext
Video Analytics Zone / Motion trace/ Face trace/ Minefield/ Absent / Cross /
Entrance/ Scene Change Detection
Privacy zone Max 15 (Tilt, Color, Transparency, Mosaic)
Effect V-Flip / Mirror / Rotation / Nega&Posi / Freeze / Sharpness
Sense-up x32
Sharpness 0~15 steps
Cam ID 001~255
WDR WDR: x512 (Level Adjust)
D-Zoom ~ x256(D-Zoom) / D-PTZ Support
Bad Pixel Adj/Done (Max 64 point), Detected pixel display
System Lock Lock/Unlock (need Password input when Locked)
Frame Control Auto, Off ~ 7Sec( Use for saving storage)
General
F
U
N
C
T
I
O
N
Other Function Admin Password, Alarm Setting(Period, Snooze, Polarity)
Power input Terminal block
Video output BNC, UTP (optional)
Lens mount Fixed Mount
Lens 2.8mm~12.0mm/F1.4 D&N DC IRIS Vari-Focal Lens
Operating Temp. -10ºC to +50ºC
Operating humidity Less than 90%
Connec
tor
& etc
External dimension 145.6 (W) x 113 (H) x / Weight : 400g

50302692A