Advantech IDK-1110P Series User manual

User Manual
IDK-1110P-series
TFT-LCD 10.4” XGA (LED
Backlight)

IDK-1110P User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2015
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.
Acknowledgements
AMI is a trademark of American Megatrends Inc.
IBM and PC are trademarks of International Business Machines Corporation.
Intel® Core 2 Quad, Pentium Dual Core and Celeron are trademarks of Intel Corpo-
ration.
WinBond is a trademark of Winbond Corporation.
All other product names or trademarks are properties of their respective owners.
Part No. 2006111030 Edition 1
Printed in Taiwan October 2015

iii IDK-1110P User Manual
A Message to the Customer
Advantech Customer Services
Each and every Advantech product is built to the most exacting specifications to
ensure reliable performance in the harsh and demanding conditions typical of indus-
trial environments. Whether your new Advantech equipment is destined for the labo-
ratory or the factory floor, you can be assured that your product will provide the
reliability and ease of operation for which the name Advantech has come to be
known.
Your satisfaction is our primary concern. Here is a guide to Advantech’s customer
services. To ensure you get the full benefit of our services, please follow the instruc-
tions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions,
you can easily find answers in your product documentation. These answers are nor-
mally a lot more detailed than the ones we can give over the phone.
So please consult this manual first. If you still cannot find the answer, gather all the
information or questions that apply to your problem, and with the product close at
hand, call your dealer. Our dealers are well trained and ready to give you the support
you need to get the most from your Advantech products. In fact, most problems
reported are minor and are able to be easily solved over the phone.
In addition, free technical support is available from Advantech engineers every busi-
ness day. We are always ready to give advice on application requirements or specific
information on the installation and operation of any of our products.
Warnings, Cautions and Notes
Warning! Warnings indicate conditions, which if not observed, can cause personal
injury!
Caution! Cautions are included to help you avoid damaging hardware or losing
data.
Note! Notes provide optional additional information.

IDK-1110P User Manual iv
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandise
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.

v IDK-1110P User Manual
Contents
Chapter 1 Overview...............................................1
1.1 General Description .................................................................................. 2
1.2 Display Characteristics.............................................................................. 2
1.3 Mechanical Specification........................................................................... 2
1.4 Mechanical Dimension .............................................................................. 3
1.5 Absolute Maximum Ratings ...................................................................... 3
1.5.1 Absolute Ratings of the TFT LCD Module .................................... 3
1.5.2 Absolute Environment Ratings...................................................... 3
1.6 Block Diagram........................................................................................... 4
Figure 1.1 TFT LCD module ........................................................ 4
Chapter 2 Electrical Characteristics....................5
2.1 TFT LCD Module....................................................................................... 6
2.1.1 Electrical Characteristics............................................................... 6
2.2 Backlight Unit ............................................................................................ 7
2.2.1 Parameter guideline for LED backlight ......................................... 7
Chapter 3 Signal Characteristics.........................9
3.1 Pixel Format Image ................................................................................. 10
3.2 Pin Description ........................................................................................ 10
Table 3.1: Pin Description ......................................................... 10
3.3 Input Data Format ................................................................................... 11
3.3.1 SEL68 ......................................................................................... 11
Table 3.2: Input Data Format..................................................... 12
3.4 Interface Timing ...................................................................................... 13
3.4.1 Timing Characteristics ................................................................ 13
Table 3.3: Timing Characteristics (For IDK-1110P-40SVA1E).. 13
3.4.2 Input Timing Diagram.................................................................. 13
3.5 Power ON/OFF Sequence ...................................................................... 14
Chapter 4 Display Connector Definition ...........15
4.1 TFT LCD Signal(CN1): LVDS Connector................................................ 16
Table 4.1: Connector ................................................................. 16
Table 4.2: Pin Assignments....................................................... 16
4.2 LED Backlight Unit (CN2): LED Driver Connector .................................. 17
Table 4.3: LED Backlight Pin..................................................... 17
Chapter 5 Touch Screen.....................................19
5.1 Touch Characteristics ............................................................................. 20
5.2 Optical Characteristics ............................................................................ 20
5.3 Environment Characteristics ................................................................... 20
5.4 Mechanical Characteristics ..................................................................... 21
Chapter 6 Touch Controller................................23
6.1 Touch Controller Characteristics............................................................. 24

IDK-1110P User Manual vi
6.2 Specifications.......................................................................................... 24
6.3 Environmental Feature............................................................................ 24
6.4 Mechanical Drawing................................................................................ 25
6.4.1 Mechanical size .......................................................................... 25
6.5 Pin Assignment and Description ............................................................. 26
6.5.1 Touch Line Pin Definition............................................................ 26
6.5.2 Interface Detection and Pin Definition ........................................ 26
Table 6.1: JL3 / 4PIN / USB ...................................................... 27
Table 6.2: JL4 / 7 PIN / I2C/ UART ........................................... 27
6.6 Connector Specification .......................................................................... 27
6.7 Driver Utilities.......................................................................................... 28
6.7.1 Drivers ........................................................................................ 28
6.7.2 Utility ........................................................................................... 28
Appendix A Optical Characteristics..................... 29
A.1 Optical Characteristics ............................................................................ 30
Appendix B Handling Precautions ....................... 33
B.1 Handling Precautions.............................................................................. 34

Chapter 1
1Overview

IDK-1110P User Manual 2
1.1 General Description
This specification applies to the 10.4 inch color TFT LCD module IDK-1110P-series.
IDK-1110P is designed with wide viewing angle; wide operating temperature and long
life LED backlight which is well suited for Industrial Applications. LED driving board
for backlight unit is included in this panel and the structure of the LED units is
replaceable. Also, IDK-1110P-series has an LVDS interface and projected capacitive
touch solution. The screen format is intended to support XGA (1024 (H) x 768 (V))
screen and 16.2M + FRC. IDK-1110P is a RoHS product.
1.2 Display Characteristics
The following items are product characteristics under 25°C conditions.
1.3 Mechanical Specification
Items Specifications Unit
Screen Diagonal 10.4 inch
Active Area 210.4 (H) x 157.8 (V) mm
Pixels H x V 1024x3(RGB) x 768 -
Pixel Pitch 0.0685 (H) x 0.2055 (V) mm
Pixel Arrangement R.G.B. Vertical Stripe -
Display Mode Transmissive mode / Normally black -
Nominal Input Voltage VDD 3.3 (typ) Volt
Typical Power Consumption 10 W (typ) Watt
Item Min. Typ. Max. Unit Note
Module Size
Horizontal(H) - 251.03 - mm
Vertical(V) - 202.42 - mm
Depth(D) - 11.32 - mm
Weight - 500 - g -

3 IDK-1110P User Manual
Chapter 1 Overview
1.4 Mechanical Dimension
1.5 Absolute Maximum Ratings
1.5.1 Absolute Ratings of the TFT LCD Module
1.5.2 Absolute Environment Ratings
Unit:mm
AA Center
2-USER HOLE M2X2.5
2-USER HOL E M2X2.5 Patone Black C
Item Symbol Value Unit
Min. Max.
Logic/LCD Drive
Voltage VCC -0.3 +7 [Volt]
Item Symbol
Value
Unit
Min. Max.
Operating Temperature TOP -20 +70 °C
Operation Humidity HOP 90 [%RH]
Storage Temperature TST -30 +80 ° C
Storage Humidity HST 90 [%RH]
Note! Maximum Wet-Bulb should be 39°C with no condensation.

IDK-1110P User Manual 4
1.6 Block Diagram
Figure 1.1 TFT LCD module

Chapter 2
2Electrical
Characteristics

IDK-1110P User Manual 6
2.1 TFT LCD Module
2.1.1 Electrical Characteristics
Ta=25 ± 2° C
Measurement Conditions:
Parameter Symbol Value Unit Note
Min. Typ. Max.
Power Supply Voltage Vcc 3.0 3.3 3.6 V (1)
Rush Current IRUSH --4.0A(2)
Power Supply Current White -530 570 620 mA (3)
Black 380 420 460 mA
Power Consumption PL--- 1.9 --- W
LVDS differential input voltage lVIDl 100.0 - 600.0 mV -
LVDS common input voltage VICM 0.7 - 1.6 V -
Note! The assembly should be always operated within above ranges.

7 IDK-1110P User Manual
Chapter 2 Electrical Characteristics
2.2 Backlight Unit
2.2.1 Parameter guideline for LED backlight
Following characteristics are measured under a stable conditions using an inverter at
25° C (Room Temperature):
Note! The specified power supply current is under the conditions at Vcc=3.3 V,
Ta=25+/- 2° C, fv=60 Hz, whereas a power dissipation check pattern is
displayed.
Parameter Symbol
Value
Unit Remark
Min. Typ. Max.
Input Voltage Vi10.8 12 13.2 [Volt] (Duty 100%)
Input Current Ii-0.7-[A]
@ Vi=12 V (Duty 100%)
Power Consumption PLED -8-[Watt]
@ Vi=12 V (Duty 100%)
PWM Control FPWM 190 200 20k [Hz]
EN Control
Level
Backlight
on 2.0 - 5 [Volt]
Backlight
off 0- 0.8[Volt]
PWM
Control
Level
PWM
High Level 2.0 - 5 [Volt]
PWM Low
Level 0 - 0.15 [Volt]
PWM Control Duty
Ratio 2- 100%
Operation
Lifetime 50,000 - - Hrs Note (2) below
Note! LED current is measured by utilizing a high frequency current meter as
shown below:
Note! The lifetime LED is defined as the time when it continues to operate
under the conditions: Ta=25 +/-2° C and I LED=80 mADC (LED forward
current) until the brightness becomes <=50% of its original value. Mini-
mum LED lifetime is estimated and provided by Nichia in Japan.

IDK-1110P User Manual 8
Pin Symbol Description Remark
1ViConverter input voltage 12 V
2ViConverter input voltage 12 V
3ViConverter input voltage 12 V
4ViConverter input voltage 12 V
5VGND Converter ground Ground
6VGND Converter ground Ground
7VGND Converter ground Ground
8VGND Converter ground Ground
9 EN Enable pin 3.3 V
10 ADJ Backlight Adjust PWM Dimming

Chapter 3
3Signal Characteristics

IDK-1110P User Manual 10
3.1 Pixel Format Image
Following figure shows the relationship between input signal and LCD pixel
format.
3.2 Pin Description
LVDS is a differential signal technology for LCD interface and high speed data trans-
fer device. The connector pin definition is as below.
1023 1024
768th
Table 3.1: Pin Description
Pin No. Symbol Description Note
1 VCC Power supply: +3.3 V
2 VCC Power supply: +3.3 V
3 VCC Power supply: +3.3 V
4 GND Ground
5 GND Ground
6 GND Ground
7 RPFI Reverse Panel Function (Display Rotation)
8 NC No Connection
9 NC No Connection
10 NC No Connection
11 SEL 6/8
LVDS 6/8 bit select function control,
Low or NC -> 8bit Input Mode
High -> 6bit Input Mode
12 GND Ground
13 NC No Connection
14 GND Ground
15 RX0- Negative transmission data of pixel 0
16 RX0+ Positive transmission data of pixel 0
17 GND Ground
18 RX1- Negative transmission data of pixel 1

11 IDK-1110P User Manual
Chapter 3 Signal Characteristics
3.3 Input Data Format
3.3.1 SEL68
SEL68 = ”Low” or “NC” for 6 bits LVDS Input
SEL68 = ”High” for 8 bits LVDS Input
19 RX1+ Positive transmission data of pixel 1
20 GND Ground
21 RX2- Negative transmission data of pixel 2
22 RX2+ Positive transmission data of pixel 2
23 GND Ground
24 RXCLK- Negative of clock
25 RXCLK+ Positive of clock
26 GND Ground
27 RX3- Negative transmission data of pixel 3
28 RX3+ Positive transmission data of pixel 3
29 GND Ground
30 NC No Connection
Note! Connector Part No.: JAE, FI-XB30SRL-HF11 or compatible.
Note! “Low” stands for 0 V. “High” stands for 3.3 V. “NC” stands for “Not Con-
nected.”
Table 3.1: Pin Description

IDK-1110P User Manual 12
Note! Please follow PSWG.
Note! R/G/B data 7: MSB, R/G/B data 0: LSB.
Table 3.2: Input Data Format
Signal Name Description Remark
R7 Red Data 7
Red-pixel Data
For 8 bits LVDS input,
MSB: R7; LSB:R0
For 6 bits LVDS input,
MSB: R5; LSB:R0
R6 Red Data 6
R5 Red Data 5
R4 Red Data 4
R3 Red Data 3
R2 Red Data 2
R1 Red Data 1
R0 Red Data 0
G7 Green Data 7
Green-pixel Data,
For 8 bits LVDS input,
MSB: G7; LSB:G0
For 6 bits LVDS input,
MSB: G5; LSB:G0
G6 Green Data 6
G5 Green Data 5
G4 Green Data 4
G3 Green Data 3
G2 Green Data 2
G1 Green Data 1
G0 Green Data 0
B7 Blue Data 7
Blue-pixel Data
For 8 bits LVDS input,
MSB: B7; LSB:B0
For 6 bits LVDS input,
MSB: B5; LSB:B0
B6 Blue Data 6
B5 Blue Data 5
B4 Blue Data 4
B3 Blue Data 3
B2 Blue Data 2
B1 Blue Data 1
B0 Blue Data 0
RXCLKIN+
RXCLKIN- LVDS Clock Input
DE Display Sync
VS Vertical Sync
HS Horizontal Sync
Note! Output signals from any system shall be low or Hi-Z state when VDD is
off.

13 IDK-1110P User Manual
Chapter 3 Signal Characteristics
3.4 Interface Timing
3.4.1 Timing Characteristics
DE mode only (For IDK-1110P-40SVA1E)
3.4.2 Input Timing Diagram
Table 3.3: Timing Characteristics (For IDK-1110P-40SVA1E)
Parameter Symbol Min. Typ. Max. Unit Condition
Clock frequency Fc 55 65 75 MHz
Vertical
Section
Period TV770 806 950
TH
TV=TVd+TVb
Active TVd - 768 -
Blanking TVb 238182
Horizontal
Section
Period Th1104 1344 1800
TClock
Th=Thd+Thb
Active Thd - 1024 -
Blanking Thb 76 320 776
Note! Frame rate is 60 Hz.
Note! DE mode. Hsync and Vsync input signals should be set to low logic level
otherwise this assembly would operate abnormally.

IDK-1110P User Manual 14
3.5 Power ON/OFF Sequence
To prevent a latch-up or DC operation of LCD assembly, the power on/off sequence
should be as the diagram below.
Power Sequence Timing
Parameter Value Unit
Min. Typ. Max.
T1 0.5 - 10 [ms]
T2 0 - 50 [ms]
T3 0 - 50 [ms]
T4 500 - - [ms]
T5 200 - - [ms]
T6 20 - - [ms]
T7 5 - 300 [ms]
T8 10 - - [ms]
T9 10 - - [ms]