Advantech IDK-1110WR-50WSA1 User manual

User Manual
IDK-1110WR-50WSA1
101" WSVGA Industrial
Display Kit with 4-Wire Resistive
Touch Solution

IDK-1110WR User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2019
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.
Acknowledgements
AMI is a trademark of American Megatrends Inc
IBM and PC are trademarks of International Business Machines Corporation
Intel® Core 2 Quad, Pentium Dual Core and Celeron are trademarks of Intel Corpo-
ration
WinBond is a trademark of Winbond Corporation
All other product names or trademarks are properties of their respective owners
Part No. 2006111022 Edition 3
Printed in Taiwan November 2019

iii IDK-1110WR User Manual
A Message to the Customer
Advantech Customer Services
Each and every Advantech product is built to the most exacting specifications to
ensure reliable performance in the harsh and demanding conditions typical of indus-
trial environments. Whether your new Advantech equipment is destined for the labo-
ratory or the factory floor, you can be assured that your product will provide the
reliability and ease of operation for which the name Advantech has come to be
known. Your satisfaction is our primary concern. Here is a guide to Advantech’s cus-
tomer services. To ensure you get the full benefit of our services, please follow the
instructions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions,
you can easily find answers in your product documentation. These answers are nor-
mally a lot more detailed than the ones we can give over the phone.
So please consult this manual first. If you still cannot find the answer, gather all the
information or questions that apply to your problem, and with the product close at
hand, call your dealer. Our dealers are well trained and ready to give you the support
you need to get the most from your Advantech products. In fact, most problems
reported are minor and are able to be easily solved over the phone.
In addition, free technical support is available from Advantech engineers every busi-
ness day. We are always ready to give advice on application requirements or specific
information on the installation and operation of any of our products.

IDK-1110WR User Manual iv
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandise
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.

1 IDK-1110WR User Manual
Contents
Chapter 1 Overview...............................................1
1.1 General Description .................................................................................. 2
1.2 Display Characteristics.............................................................................. 2
1.3 Display Optical Characteristics ................................................................. 3
1.3.1 Measuring Condition ..................................................................... 3
1.3.2 Measuring Equipment ................................................................... 3
1.4 Block Diagram........................................................................................... 5
Figure 1.1 TFT LCD Module ........................................................ 5
1.5 Absolute Maximum Ratings ...................................................................... 5
1.5.1 Absolute Max Rating..................................................................... 5
1.6 Dimensions ............................................................................................... 6
1.6.1 Front View..................................................................................... 6
1.6.2 Rear View ..................................................................................... 6
Chapter 2 Electrical Characteristics...................7
2.1 TFT LCD Module....................................................................................... 8
2.1.1 Power Specifications..................................................................... 8
2.1.2 LVDS DC Electrical Characteristics .............................................. 8
2.1.3 LVDS AC Electrical Characteristics .............................................. 9
2.2 Backlight Unit .......................................................................................... 10
2.2.1 Parameter Guidelines for LED Backlight .................................... 10
Chapter 3 Signal Characteristics.......................11
3.1 Electrical Interface Connection ............................................................... 12
Table 3.1: Connector ................................................................. 13
3.2 The Input Data Format ............................................................................ 13
3.3 Interface Timing ...................................................................................... 14
3.3.1 Timing Characteristics ................................................................ 14
Table 3.2: Timing Characteristics .............................................. 14
3.3.2 Input Timing Diagram.................................................................. 14
3.4 Power ON/OFF Sequence ...................................................................... 15
Chapter 4 Touch Screen.....................................17
4.1 Touch Characteristics ............................................................................. 18
Chapter 5 Touch Controller................................19
5.1 Touch Controller Characteristics............................................................. 20
5.2 Specifications .......................................................................................... 20
5.3 Environmental Features .......................................................................... 20
5.4 Pin Assignments and Description ........................................................... 21
5.4.1 Connector and LED Location...................................................... 21
5.4.2 Combo Interface Connector, JP1, Pins and Signal Descriptions 21
Figure 5.1 Board Mounted Header ............................................ 21
5.4.3 Touch Screen Connector, JP2, Pins and Signal Descriptions .... 21
Appendix A LCD EDID............................................23

IDK-1110WR User Manual 2
A.1 LCD EDID ............................................................................................... 24

Chapter 1
1Overview

IDK-1110WR User Manual 2
1.1 General Description
This specification applies to the 10.1 inch color TFT LCD module IDK-1110WR-
50WSA1. IDK-1110WR-50WSA1 is designed with a wide viewing angle, wide operat-
ing temperature range, and along lifespan for the LEDs backlight; making it well
suited as a display unit for Industrial Applications. An LED driving board for the back-
light unit is included in this panel. IDK-1110WR-50WSA1 uses a built in timing con-
troller and LVDS interface. The screen format is intended to support the WSVGA
(1024(H) x 600(V)) screen and 262k colors (RGB 6-bits). IDK-1110WR-50WSA1 is a
RoSH product.
1.2 Display Characteristics
The following characteristics are summarized on the table below for under 25°C con-
ditions.
Items Specifications Unit
Screen Diagonal 10.1 (Diagonal) inch
Active Area 222.72(H) x 125.28(V) mm
Pixels H x V 1024 x 3(RGB) x 600
Pixel Pitch 0.2715 x 0.2088 mm
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode TN, Normally White
Nominal Input Voltage VDD 3.3 typ Volt
Typical Power Consumption 3.834 typ. Watt
Weight 180 ± 10 Grams
Physical Size 235.0(W) x 143 (H) x 4.9 (D) (typ.) mm
Electrical Interface 1 channel LVDS
Surface Treatment Anti-glare, Hardness 3H
Support Color 262K(6-bit) / 16.7M (8-bit)
Temperature Range
Operating Storage (Non-Operating)
-5 to + 60
-20 to +70
°C
°C
RoHS Compliance RoHS Compliance

3 IDK-1110WR User Manual
Chapter 1 Overview
1.3 Display Optical Characteristics
The optical characteristics are measured under stable conditions at 25°C (Room
Temperature):
1.3.1 Measuring Condition
Measuring surrounding: dark room
Ambient temperature: 25±2°
15 min. warm-up time
1.3.2 Measuring Equipment
The optical characteristics are measured in a dark room. After 30 minutes operation,
the optical properties are measured at the center point of the LCD screen. (Response
time is measured by a Photo detector TOPCON BM-7 of view: 1° / Height: 120 mm.)
Note1: Definition of viewing angle range
Item Symbol Conditions Values Unit Note
Min. Typ. Max.
Viewing Angle
 L (CR 10) 60 70 -- degree 1, 2
 R60 70 --
 U50 60 --
 D50 60 --
Response Time TR+TF - 20 35 msec 3
Contrast Ratio CR 400 500 -- - 2
Color Chromaticity WX 0.263 0.313 0.363 - 1, 4
WY 0.279 0.329 0.379 -
RX 0.512 0.562 0.612 -
RY 0.281 0.331 0.381 -
GX 0.279 0.329 0.379 -
GY 0.522 0.572 0.622 -
BX 0.11 0.160 0.210 -
BY 0.084 0.134 0.184 -
Luminance L 400 500 -- cd/m24
Luminance Uniformity YU 80 -- -- % 5

IDK-1110WR User Manual 4
Note 2: Definition of Contrast Ratio
Contrast ratio is calculated with the following formula :
Contrast Ratio (CR)=(White) Luminance of ON ÷ (Black) Luminance of OFF
Note 3: Definition of Response time: Sum of TR and T
Note 4: Definition of optical measurement setup
Note 5: Definition of brightness uniformity
(Min Luminance of 5 points)
Luminance uniformity =------------------------------------------------×100%
(Max Luminance of 5 points)
Note 6: Rubbing Direction (The different Rubbing Direction will cause the different
optimal view direction
Note 7: Condition: Ta=25°C, Life time is estimated data.

5 IDK-1110WR User Manual
Chapter 1 Overview
Definitions of failure:
1. LCM brightness becomes half of the minimum value.
2. LED doesn’t light normally.
1.4 Block Diagram
Figure 1.1 TFT LCD Module
1.5 Absolute Maximum Ratings
1.5.1 Absolute Max Rating
Note: Maximum Wet-Bulb should be 39°C and no condensation.
Item Symbol
Value
Unit Note
Min. Max.
Logic/LCD Drive Voltage VCCS -0.3 4.0 V
EDID Drive Voltage VEDID -0.3 4.0 V
Converter Input Voltage LED_VCCS -0.3 23 V
Converter Control Signal PWM Voltage LED_PWM -0.3 6.0 V
Converter Control
Signal Enable Voltage LED_EN -0.3 6.0 V
Operating Temperature TOPA -5 60 °C
Storage Temperature TSTG -20 70 °C

IDK-1110WR User Manual 6
1.6 Dimensions
1.6.1 Front View
1.6.2 Rear View
Note: Tolerances unless marked are ±0.5mm

Chapter 2
2Electrical
Characteristics

IDK-1110WR User Manual 8
2.1 TFT LCD Module
2.1.1 Power Specifications
Input power is shown as follows:
Note: Measurement condition:
2.1.2 LVDS DC Electrical Characteristics
Input signals should be low or Hi-Z states when VCCS is off.
Note: LVDS Signal Waveform.
Item Symbol
Value
Unit Note
Min. Typ. Max.
Logic/ LCD Driver Voltage VCCS 3.0 3.3 3.6 V
VCCS Current IVCCS - 0.14 0.16 A
VDD=3.3V, at
60Hz
Black Pattern
LCD Inrush Current Iruch - - 1.5 A 1
VCC Power PVCCS - 0.46 0.53 Watt
VCCS=3.3V, at
60HZ
Balck Pattern
Allowable Logic/LCD
Drive Ripple Voltage VCCSrp - - 150 mV p-p
Parameter Symbol
Value
Unit Remark
Min. Typ. Max.
Differential Input
High Threshold
VTH - - 100 mV
Differential Input
Low Threshold
VTL -100 - - mV
Differential Input Voltage VID 100 - 600 mV
Common Mode Voltage Offset VICM 1.125 - 1.375 V
LVDS Terminal Resistor ICRTC - 100 - Ohm

9 IDK-1110WR User Manual
Chapter 2 Electrical Characteristics
2.1.3 LVDS AC Electrical Characteristics
Item Symbol Min. Typ. Max. Unit Remark
Differential Pulse Skew tSKD 0.5 ns
Transition Low to High
Time
tTLH 1 ns
Transition High to Low
to Time
tTHL 1 Ns
Offset Voltage Imbal-
ance
VOS 200 mV

IDK-1110WR User Manual 10
2.2 Backlight Unit
2.2.1 Parameter Guidelines for LED Backlight
The following characteristics are measured under a stable condition using an inverter
at 25°C (Room Temperature):
Note1: Condition: Ta=25°C, continuous lighting
Life time is estimated data. Definitions of failure:
1. LCM brightness becomes half of the minimum value.
2. LED doesn’t light normally.
Parameter Symbol
Value
Unit Note
Min. Typ. Max.
LED Driver Voltage LED_VCCS 9 12 15 V
Input Current ILED - 225 270 mA VLED=12V
(duty 100%)
Power Consumption PLED - 2.7 3.3 W
LED_EN Voltage BL On 2.3 - 5 V
BL Off 0 - 0.5 V
PWM Frequency FPWM 190 2000 Hz
PWM Duty Ratio DPWM 10 - 100 %
PWM Control Level High Level 2.3 - 5 V
Low Level 0 - 0.5
LED Life Time 50,000 Hour

Chapter 3
3Signal Characteristics

IDK-1110WR User Manual 12
3.1 Electrical Interface Connection
Note: Inpout Signals shall be in low status when VCCS is off
Pin No. Symbol Description Note
1 NC No connection
2 VCCS 3.3V Power
3 VCCS 3.3V Power
4V_EDID
3.3V Power for EDID, if EDID function is not used, please keep it
floating.
5 NC No connection, 100K pull-down resistance in LCM
6 CLK_EDID EDID Clock Input, if EDID function is not used, please keep it floating.
7 DATA_EDID EDID Data Input, if EDID function is not used, please keep it floating.
8 RXIN0- LVDS Signal - channel0-
9 RXIN0+ LVDS Signal+ channel0+
10 GND Ground
11 RXIN1- Data Input channel1-
12 RXIN1+ Data Input channel1+
13 GND Ground
14 RXIN2- Data Input channel2-
15 RXIN2+ Data Input channel2+
16 GND Ground
17 RXCLKIN- Data Input CLK-
18 RXCLKIN+ Data Input CLK+
19 GND Ground
20 RXIN3- Data Input channel 3
21 RXIN3+ pin 20 & pin 21 connect to GND or NC for 6bit LVDS input
22 GND Ground
23 NC No connection
24 NC No connection
25 GND Ground
26 Order_SEL LVDS format selection.
Order_SEL="H": JEIDA/Order_SEL="L" or NC: NS-Like
27 SEL68 6/8 bits LVDS data input selection
SEL68="H": 8bits/ SEL68="L" or NC: 6bit
28 GND Ground
29 NC No connection
30 NC No connection
31 LED_GND LED Ground
32 LED_GND LED Ground
33 LED GND LED Ground
34 NC No connection
35 LED_PWM PWM Control Signal of LED Converter
36 LED_EN Enable Control Signal of LED Converter
37 NC No connection
38 LED_VCCS LED Power 12V
39 LED_VCCS LED Power 12V
40 LED_VCCS LED Power 12V

13 IDK-1110WR User Manual
Chapter 3 Signal Characteristics
3.2 The Input Data Format
Note: Output signals from any system shall be low to Hi-Z state when VCCS is off.
Table 3.1: Connector
Manufacture IPEX or compatible
Connector Model Number IPEC 20455-040E-12R or compatible
Adaptable Plug IPEC 20453-040T-01 or compatible

IDK-1110WR User Manual 14
3.3 Interface Timing
3.3.1 Timing Characteristics
DE mode only
Note: DE Mode
3.3.2 Input Timing Diagram
Table 3.2: Timing Characteristics
Item Symbol Min. Typ. Max. Unit
Clock Frequency Tdclk 40.8 51.2 67.2 MHz
Horizontal
Section
Period TV1114 1344 1400
Tdlck
Active TVD 1024 1024 1024
Blanking TVB 90 320 376
Vertical
Section
Period TH610 635 800
TLine
Active THD 600 600 600
Blanking THB 10 35 200
Frame rate F 50 60 70 Hz