AEG 8160 D User manual

8160 D/8190 D
Dunstabzugshaube
Afzuigkap
Hotte aspirante
Cooker Hood
Montage- und Gebrauchsanweisung
Installatie- en gebruiksaanwijzing
Notice d’utilisation et d’installation
Operating and Installation Instructions

64
Contents
Safety warnings 65
fortheuser 65
fortheinstaller 65
Description of the Appliance 67
Extractorversion 67
FilterVersion 67
Hood Operation 68
Maintenance and care 69
Metalgreasefilter 69
Openthemetalgreasefilter 69
Charcoalfilter 70
Changingthelightbulb 71
Cleaning 72
Special accessories 72
Technical assistance service 72
Guarantee conditions 73
Technic Details 75
Mountingaccessoriesincluded 75
Electrical connection 76
Safetywarningsfortheelectrician 76
Wall unit mounting 77
Printedonrecycledpaper
AEG - putting words into action

65
Safety warnings
for the user
•Alwayscoverlighted elements, to prevent excessheatfrom
damaging the appliance. In the case of oil, gas and coal fired
cookers it is essential to avoid open flames.
•Also, when frying, keep the deep frying pan on the cooker top/cooker
undercarefulcontrol.
•Thehotoil in the fryingpanmight ignite due tooverheating.
•The risk of self-ignition increases when the oil being used is dirty.
•It is extremely important to note that overheating can cause a fire.
•Never carry out any flambécooking under the hood.
•Always disconnect the unit from the power supply before
carrying out any work on the hood, including replacing the
light bulb (take the cartridge fuse out of the fuse holder or switch off
theautomatic circuit breaker).
•It is very important to clean the hood and replace the filter at
the recommended intervals. Failure to do so could cause
grease deposits to build up, resulting in a fire hazard.
•Theapplianceis not intended for useby young children or infirm
personswithoutsupervision.
•Young children should be supervised to ensure that they do not play
withtheappliance.
•WARNING - Ensure that theapplianceis switched offbefore
replacing the lamp to avoid the possibility of electric shock.
for the installer
•When used as an extractor unit, the hood must be fitted with a
150mmdiameterhose.
•Should there already be a pipe of diameter 125 mm that ducts to the
outside through the walls or roof, it is possible to use the 150/125
mm reduction flange provided. In this case the hood will be slightly
morenoisy.
•When installing the hood, make sure you respect the following
minimum distance from the top edge of the cooking hob/ring
surfaces:
electric cookers 500 mm
gascookers 650 mm
coal and oil cookers 700 mm min.
•ThenationalStandardonfuel-burning systems specifies a maximum
depression of 0.04 bar in such rooms.

66
•The air outlet must not be connected to chimney flues or combustion
gas ducts. The air outlet must under no circumstances be connected
toventilationductsforroomsinwhichfuel-burningappliancesare
installed.
•Itisadvisabletoapplyforauthorizationfromtherelevantcontrolling
authority when connecting the outlet to an unused chimney flue or
combustion gas duct.
The air outlet installation must comply with the regulations laid down
bytherelevantauthorities.
•When the unit is used in its extractor version, a sufficiently large
ventilationholemustbeprovided,withdimensionsthatare
approximately the same as the outlet hole.
•Nationalandregionalbuildingregulationsimposeanumberof
restrictionsonusinghoodsandfuel-burningappliances connected to
a chimney, such as coal or oil room-heaters and gas fires, in the
sameroom.
•Hoods can only be used safely with appliances connected to a
chimneyiftheroomand/orflat(air/environmentcombination)is
ventilatedfromoutsideusingasuitableventilationholeapproximately
500-600cm2 largeto avoid the possibility ofadepression being
createdduringoperationofthehood.
•Ifyouhaveany doubts, contact the relevant controllingauthorityor
buildinginspector’soffice.
•Since the rule for rooms with fuel burning appliances is “outlet hole of
the same size as the ventilation hole”, a hole of 500-600 cm2, which
is to say a larger hole, could reduce the performance of the extractor
hood.
•If the hood is used in its filtering function, it will operate simply and
safelyin the above conditions without the need for any of the
aforementionedmeasures.
•When the hood is used in its extractor function, the following rules
mustbefollowedto obtain optimal operation:
—short and straight outlet hose
—keep bends in outlet hose to a minimum
—never install the hoses with an acute angle, they must
always follow a gentle curve only
—keep the hose as large as possible (preferably the same diameter
as the outlet hole).
•Failure to observe these basic instructions will drastically reduce the
performanceandincreasethenoiselevelsoftheextractorhood.

67
Description of the Appliance
Extractor version
•The hood is supplied as an extractor unit
and can also be used with a filtering
functionbyfitting one charcoal filter
(special accessory).
•Youwill need originalAEG charcoal filter
for this function (see Special
Accessories).
•The air is discharged to the outside
through a pipe, which must be fitted to
connection flange A. Fig. 1.
•Inordertoobtainthebestperformance
thehoseshouldhave a diameter equal to
the outlet hole.
Should there already be a pipe of diameter 125 mm that ducts to the
outside through the walls or roof, it is possible to use the 150/125
mm reduction flange provided. In this case the hood will be slightly
morenoisy.
Filter Version
•Theairis filtered through an charcoal filterandreturned to the
kitchen through the top grill of the outlet pipe.
•You will need an original AEG KF8 charcoal filter for the filtering
function. (See Special Accessories).
•Fix the deflector using 2 screws Ø2,9x13 mm. Fig. 2.
•Optionally, the position of the chimney elements can be changed.
When using the hood in the filter
version the chimney must be fixed at
the top, with the air outlet grill at the
side.
Fig. 1
Fig. 2

68
Hood Operation
•Best results are obtained by using a low speed for normal conditions
andhighspeedwhenodoursaremoreconcentrated.Turnthehood
on a few minutes before you start cooking then you will get an
underpressurein the kitchen. It should be lefton after cooking for
about15minutesoruntilallodourshavedisappeared.
The control switches are located on the unit’s front panel:
•the light switch switches the hood lamp on and off.
•the motor switch switchesthe cooking smokeand vapour extractor
motor on and off, enabling you to select the speed.

69
Maintenance and care
•The hood must always be disconnected from the electricity
supply before beginning any maintenance work.
Metal grease filter
•Thepurpose of the grease filters is to aspirate grease particles which
form during cooking and it must always be used, either in the
externalevacuationorinternalrecyclingfunction.
Attention:themetal grease filters must beremoved and washed,
eitherbyhandor in the dishwasher,everyfourweeks.
Open the metal grease filter
•First, push the metal grease filter stop backwards, then extract the
filter, pullingdownwards.
Fig. 4.
Hand washing
Soakgreasefiltersfor
aboutonehourin hot water
withagrease-loosening
cleaner, then rinse off
thoroughlywithhotwater.
Repeattheprocess if
necessary. Refit the grease
filters when they are dry.
Dishwasher machine
Place grease filters in dish
washer. Select most powerful washing programmeandhighest
temperature,at least 65°C. Repeat theprocess. Refit the grease
filters when they are dry.
When washing the metal grease filter in the dishwasher a slight
discoloration of the filter can occur, this does not have any impact on
itsperformance.
•Cleantheinnerhousingusingahotdetergentsolution only (never
usecausticdetergents,abrasivepowdersorbrushes).
Fig. 4

70
Charcoal filter
•The charcoal filter should only be used if you want to use the hood in
itsfilteringfunction.
•To do this you will need an original AEG charcoal filter (see special
accessories).
•Cleaning/replacing the charcoal filter
Unlikeothercharcoal filters, the LONGLIFE charcoalfiltercan be
cleanedandreactivated. At normal use the filtershould be cleaned
everysecondmonth (when using thehood2,5 hours per day,in
avarage). The best way to clean the filter is in the dishwasher. Use
normaldetergentandchoose the highest temperature (65ºC). Wash
the filter separately so that no food parts gets stuck on the filter and
latercauses bad odours. Toreactivatethe charcoal, the filtershould
bedriedin an oven for 10minuteswith a temperature of maximum
100ºC.
After approximately three years of use, the charcoal filter should be
replaced with a new, as the odour reduction capacity will be reduced.
•Mounting - Fig. 5
Put the charcoal filter frame in place and fix it with 5 screws.
Fit the charcoal filter first from the rear side and fix it frontwards
using the two red keys A.
•To dismount proceedinreverseorder.
•Alwaysspecifythe hood model code numberandserial number
whenorderingreplacementfilters.Thisinformationisshownonthe
registration plate located on the inside of the unit.
•Thecharcoal filter can be orderedfrom the AEG technical assistance
service.
Fig. 5

71
Warning
•Failuretoobserve the instructions on cleaningtheunit and changing
thefilters will cause a fire hazard. You are therefore strongly
recommendedtofollowtheseinstructions.
•Themanufacturerdeclinesall responsibility for any damage tothe
motororanyfiredamagelinkedtoinappropriatemaintenanceor
failuretoobservetheabovesafetyrecommendations.
Changing the light bulb
•Disconnect the cooker hood from the main supply.
•Removethelampcover. Fig. 6.
•Replace the old bulb with a new one of the same type.
•Remountthe lamp cover.
•If the light does not come on, make sure the bulb has been inserted
in correctly before contacting the technical assistance service.
Fig. 6

72
Cleaning
•Warning:always disconnect the hood from the mains power supply
beforecleaning it.
Neverinsertpointedobjects in the motor’s protective grid.
•Washtheoutside surfaces using a delicatedetergentsolution. Never
usecausticdetergentsorabrasivebrushes or powders.
•Only ever clean the switch panel and filter grille using a damp cloth
anddelicatedetergents.
•It is extremely important to clean the unit and change the filters at
therecommendedintervals. Failure to do sowillcause grease
deposits to build up that could constitute a fire hazard.
Special accessories
CharcoalKF8(typ150) 942120 399
Technical assistance service
You are welcome to telephone our technical assistance service (see list
oftechnicalassistancecentres)whenever you need information or in the
unlikelyeventofa fault.
When calling, please be ready to specify:
1. The model code number
2. The serial number (E-Nr.)
3. The manufacturing number (F-Nr.)
This information is shown on the registration plate inside the unit
behind the grease filter.
We reserve the right to change specifications and colours as a result of
ourpolicy of continuing technological development.

73
Guarantee conditions
GuaranteeConditions
AEGofferthefollowingguaranteetothefirstpurchaserofthisappliance.
1.Theguaranteeisvalidfor12months commencing when the appliance
ishandedover to the firstretailpurchaser,which must be verifiedby
purchaseinvoice or similar documentation.Theguaranteedoesnot
covercommercialuse.
2.The guarantee covers all parts or components which fail due to faulty
workmanshiporfaulty materials. The guarantee does not cover
applianceswheredefectsorpoorperformanceareduetomisuse,
accidentaldamage,neglect,faultyinstallation,unauthorised
modificationorattemptedrepair,commercialuseorfailuretoobserve
requirementsandrecommendations set out in theinstructionbook.This
guaranteedoesnotcover such parts as light bulbs,removableglass-
ware or plastic.
3. Shouldguarantee repairs be necessarythe purchaser must inform the
nearestcustomer service office(manufacturer`sserviceor authorised
agent). AEG reserves the right to stipulate the place of the repair
(i.e.the customer`s home, place of installation or AEG workshop).
4.Theguaranteeorfreereplacementincludesbothlabourandmaterials.
5.Repairscarriedoutunderguaranteedonotextendtheguarantee
periodfor the appliance.Partsremovedduring guarantee repairs
become the property of AEG.
6.The purchaser`s statutory rights arenot affected by thisguarantee.
European Guarantee
If you should move to another country within Europe then your guarantee
moves with you to your new home subject to the following qualifications:
- Theguaranteestarts from the date youfirstpurchased your product.
- Theguarantee is for the sameperiod and to thesame extent for labour
and parts as exist in the new country of use for this brand or range of
products.
- Thisguaranteerelatesto you an cannot be transferred toanotheruser.
- Yournewhomeis within the European Community (EC) or European
FreeTradeArea.
- The product is installed and used in accordance with our instructions
and is only used domestically, i.e. a normal household.
- The product is installed taking into account regulations in your new
country.

74
BeforeyoumovepleasecontactyournearestCustomerCareCentre,listed
below,to give them details of your newhome.They will thenensure that the
localServiceOrganisationisawareofyourmoveandabletolookafteryouand
yourappliances.
France Senlis [phone]
Germany Nürnberg [phone]
Italy Pordenone [phone]
Sweden Stockholm [phone]
UK Slough [phone]

75
Technic Details
Dimensions (8160 D - in cm):
Height x Width x Depht 800-1350 x 598X x 470
Dimensions (8190 D - in cm):
Height x Width x Depht 820-1370 x 898 x 480
Maximum absorbed power: 170 W
Motorabsorption: 1 x 155 W
Lighting: 1 x 11 W
Lenght of the cable: 100 cm
Mounting accessories included
6 wall plugs Ø8 mm
6 wood-screws 5 x 45 mm
2 metal screws 2,9 x 13
4 metal screws 2,9 x 6,5
5 metal screws 3,5 x 13
2 hooks
1chimney support
2 clamps
1deflector
1reductionflangeØ150-125mm
1charcoalfilterframe
1allen spanner

76
Electrical connection
Safety warnings for the electrician
Beforeconnectingtheappliancetothepowersupply, check that the volt-
ageindicatedon the rating plate corresponds tothemains power supply
available. Appliancesfitted withaplugcan be connectedtoanystandard
power socket within easy access.
Shoulditbenecessarytoprovideafixedconnection,thehood must only
be installed by an electrician authorised by the local electricity board.
When installing, an omnipolar disconnector with a distance of at least
3mmbetweencontactsmustbe provided.
Themanufacturedeclinesall responsibilityformalfunctionsresultingfrom
failureto comply with the aboveinstructions.
Electrical connection
220-240 V –by means of fixed power cable with plug.
(Fixedconnection of the appliance mustonlybecarriedoutbyan author-
isedelectrician.)

77
Wall unit mounting - Fig. 7
•Position the template on the wall (1) and mark the position, and drill
(2) the holes (2 x Ø8 mm).
•Mount the two wall plugs with the hooks (3).
•Hang the hood on the hooks and level it with the adjustment screws
(4).
•Removethegrease filters(5) andmark for the two screws(6).
Remove the hood and drill the holes (2 x Ø8 mm).
Insert the rawl plugs (7) and hang the hood on the wall again. Adjust
it with the screws (8) and secure it with the screws (9).
•Mount the chimney support (10) with the wall plugs (9) and the
screws (11). Be careful that it is centered over the hood and
horizontallyaligned.
•Extractor version (S):Connectatube between the hood airoutlet
and the wall or roof exhaust channel. Fix it with the tube clamps
supplied.
Filter version (K): Mount the deflector with the two screws supplied
(2,9x13mm)(13).
•Maketheelectricalconnection(14) (see previous page)
•Place the chimney (15) and fix it to the top chimney support with the
two screws (16) supplied (2,9x6,5 mm). Lower the bottom part of the
chimney (17) and fasten it to the top of the hood with two screws,
supplied(18) (2,9x6,5mm).

78
Electrichob 500mm
Gashob 650mm
Fig. 7

79
240
22
599-899
370
270
350
Exhaust tube
Poweroutlet
Electrichob 500mm
Gashob 650mm
Wall bracket
Electrichob 500mm
Gashob 650mm
8190 D 8160 D

AEG Hausgeräte GmbH
Postfach 1036
D-90327 Nürnberg
http://www.aeg.hausgeraete.de
© Copyright by AEG LI1CRF ed. 05/02