AEM ASM-TS150 User manual

CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
INSTALLATION AND OPERATION MANUAL
REV 1.00 Nov 13, 2019
Anodyne Electronics Manufacturing Corp.
15-1925 Kirschner Road
Kelowna, BC, Canada.
V1Y 4N7
Telephone [phone]
Facsimile [phone]
Website: www.aem-corp.com
© 2019 Anodyne Electronics Manufacturing Corp. (AEM),
All Rights Reserved
ASM-TS150/TS300
TS1
50/TS300 Loud
Speakers

TS150/TS300 Loud Speakers
ASM-TS150/TS300 Installation and Operation Manual
Installation and Operation Manual Page ii
ENG-FORM: 820-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
COPYRIGHT STATEMENT
© 2019 Anodyne Electronics Manufacturing Corp. (AEM), All Rights Reserved
This publication is the property of AEM and is protected by Canadian copyright laws.
No part of this document may be reproduced or transmitted in any form or by any
means including electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of AEM.

TS150/TS300 Loud Speakers
ASM-TS150/TS300 Installation and Operation Manual
Installation and Operation Manual Page iii
ENG-FORM: 820-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
Prepared By:
Checked By:
Approved By:
The status of this installation and operation manual is controlled by issue shown on the title page. The
status of each section is controlled by revision shown in the footer of each page. All revisions affecting
sections of this manual have been incorporated into the latest issue.
AEM MANUAL REVISIONS
Section
Revision Number
Revision Description
Date
All
1.00
Initial Release
Nov 13, 2019
Duane Stewart
Designer
Nov 13/19
Tony Pearson
Designer
Nov 15, 2019
Tom Betzelt
Product Support
Manager
Nov 18, 2019
Ron Briggs
R&D Mgr Designate
Nov 25, 2019

TS150/TS300 Loud Speakers
ASM-TS150/TS300 Installation and Operation Manual
Installation and Operation Manual Page iv
ENG-FORM: 820-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
Table of Contents
Section Title Page
1.0 Description
1.1 Introduction 1-1
1.2 Purpose of Equipment 1-1
1.3 Features 1-1
1.4 Specifications 1-1
1.4.1 Performance Specifications 1-1
1.4.2 Physical Specifications 1-1
1.5 System Configuration 1-2
2.0 Installation
2.1 Introduction 2-1
2.2 Unpacking and Inspection 2-1
2.2.1 Warranty 2-1
2.3 Installation Procedures 2-1
2.3.1 Warnings 2-1
2.3.2 Cautions 2-1
2.3.3 Cabling and Wiring 2-2
2.3.4 Mechanical Installation 2-2
2.3.5 Post-Installation Checks 2-3
2.4 Continued Airworthiness 2-3
2.5 Installation Drawings 2-3
3.0 Operation
3.1 Introduction 3-1
3.2 General 3-1
3.3 Operation Specifics 3-1
3.3.1 Cautions 3-1

TS150/TS300 Loud Speakers
ASM-TS150/TS300 Installation and Operation Manual
Nov 13, 2019 Rev: 1.00 Page 1-1
ENG-FORM: 800-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
Section 1.0 Description
1.1 Introduction
This manual contains information on the TS150 and TS300 Loud Speakers. Information in this section
consists of purpose of equipment, features and specifications.
1.2 Purpose of Equipment
The TS150 and TS300 Loud Speakers can be used for both internal and external aircraft applications. The
TS150 and TS300 Loud Speakers are used with the LSA150, LSA300 and LSA400 series amplifiers.
1.3 Features
This TS150 and TS300 Loud Speakers offer full 150 and 300 watt capability respectively, and the driver
assembly and mechanical parts are field replaceable for ease of maintenance.
1.4 Specifications
1.4.1 Performance Specifications
Loudspeaker
Impedance
Frequency
Sensitivity @ 1W/1m
Max SPL @ 1m
TS150
11 Ω
350 –6000 Hz
105 ±3 dB
125 ±3 dB (@ 120 W)
TS300
5.5 Ω
350 –6000 Hz
106 ±3 dB
128 ±3 dB (@ 230 W)
Note: These specifications reflect installation with the LSA400-001 Amplifier and are given for guidance
only. If further information is required, please contact the Product Support department at AEM.
1.4.2 Physical Specifications
See the appropriate Mechanical Installation drawings (922-0) in Section 2 of this manual for the Loud
Speaker physical specifications.

TS150/TS300 Loud Speakers
ASM-TS150/TS300 Installation and Operation Manual
Nov 13, 2019 Rev: 1.00 Page 1-2
ENG-FORM: 800-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
1.5 System Configuration
The TS150 and TS300 Loud Speakers should be chosen to match the audio output power of the PA
System amplifier. As a general rule, the system should have one speaker driver (minimum) for each 150
watts of audio power.
Failure to follow this rule can result in the speakers being overdriven, leading to high levels of distortion
and premature failure of the speaker drivers.
End of Section 1.0

TS150/TS300 Loud Speakers
ASM-TS150/TS300 Installation and Operation Manual
Nov 13, 2019 Rev: 1.00 Page 2-1
ENG-FORM: 805-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
Section 2.0 Installation
2.1 Introduction
Information in this section consists of: unpacking and inspection procedures, installation procedures, post-
installation checks, and installation drawings.
2.2 Unpacking and Inspection
Unpack the equipment carefully. Inspect the unit visually for damage due to shipping and report all such
claims immediately to the carrier involved. Note that each unit should have the following:
- TS150/TS300 Loud Speaker
- Acceptance Test Report
- Release certification (as applicable)
Verify that all items are present before proceeding and report any shortage immediately to your supplier.
2.2.1 Warranty
All Anodyne Electronics Manufacturing Corp. (AEM) products are warranted for 2 years. See the website
www.aem-corp.com for complete details.
2.3 Installation Procedures
2.3.1 Warnings
Stand clear, this equipment operates at an intense sound level. Personnel must be kept away from the
direct loudspeaker beam.
2.3.2 Cautions
Do not operate the equipment in a hangar or in confined areas without proper hearing protection.
Do not operate the equipment with snow, water or other foreign matter in the loudspeaker horn.
Do not clean the loudspeaker with compressed air.
For continuous tone or siren audio at full output, limit the operation to a 20% duty cycle. One minute
maximum on time followed by 4 minutes off time.

TS150/TS300 Loud Speakers
ASM-TS150/TS300 Installation and Operation Manual
Nov 13, 2019 Rev: 1.00 Page 2-2
ENG-FORM: 805-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
2.3.3 Cabling and Wiring
All unshielded wire shall be selected in accordance with AC43.13-1B Change 1, Paragraphs 11-76 through
11-78. Wire types should be to MIL-W-22759 as specified in AC43.13-1B Change 1, Paragraphs 11-85,
11-86, and listed in Table 11-11.
For shielded wire applications, use Tefzel MIL-M-27500 or MIL-M-81044 shielded wire with solder sleeves
(for shield terminations) to make the most compact and easily terminated interconnect. Follow the wiring
diagrams in Section 2.5 as required.
2.3.4 Mechanical Installation
The installing agency is responsible for the design, engineering and installation of the mounting bracket for
the Speaker. Careful consideration should be given to the operating environment and the mechanical forces
acting upon the unit.
When installing the speakers, ensure that there is adequate airflow to cool the speaker drivers, and
that the speaker phasing is correct.
CAUTION
Failure to install the TS300 speakers as shown in the relevant wiring
diagram(s) will result in PERMANENT AND IRREPARABLE DAMAGE
to the speaker drivers.
Both speaker drivers MUST be wired in phase to ensure proper
performance and to prevent damage.
Recommended Mounting
Hardware:
Bolt: 10-24 panhead
screw or similar.
Qty: 3

TS150/TS300 Loud Speakers
ASM-TS150/TS300 Installation and Operation Manual
Nov 13, 2019 Rev: 1.00 Page 2-3
ENG-FORM: 805-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
2.3.5 Post-Installation Checks
Ensure all connectors are tight and the mechanical installation is sound.
When the PA system installation is complete, carry out a full performance test to ensure that all components
of the system (including the speaker) are functioning correctly. For full post-installation check information,
refer to Section 2 of the ASM-LSA400 Loud Speaker Amplifier Service manual.
2.3.5.1 Bonding
If required, bonding is normally achievable through the mounting points during installation of the product
using conductive hardware. If the hardware and/or mounting location/surface is non-conductive, then the
use of a bonding strap to an airframe ground point is required. The bonding strap should be as short as
possible. If the product finish is non-conductive, recommend removing the finish around one of the
mounting points. Treat the exposed metal areas with a protective, conductive coating.
The use of a milli-ohmmeter is recommended to verify bonding. Reference AC 43.13-1B Change 1, Section
15 for additional information.
2.4 Continued Airworthiness
Maintenance of the TS150/TS300 Loud Speakers is ‘on condition’ only. Periodic maintenance of this
product is not required.
2.5 Installation Drawings
DRAWING
REV.
DESCRIPTION
TYPE
SERIAL NO.
TS150
TS150\403-0
1.00
Loud Speaker, Compact, 150W
Interconnect
61339+
TS150\403-1
1.00
Loud Speaker, Compact, 150W
Interconnect
61339+
TS150\405-0
1.00
Loud Speaker, Compact, 150W
Connector Map
61339+
TS150\922-0
1.00
Loud Speaker, Compact, 150W
Mech. Installation
61339+
TS300
TS300\403-0
1.00
Loud Speaker, Compact, 300W
Interconnect
61339+
TS300\403-1
1.00
Loud Speaker, Compact, 300W
Interconnect
61339+
TS300\403-2
1.00
Loud Speaker, Compact, 300W
Interconnect
61339+
TS300\405-0
1.00
Loud Speaker, Compact, 300W
Connector Map
61339+
TS300\922-0
1.10
Loud Speaker, Compact, 300W
Mech. Installation
82274+
TS300\922-0
1.00
Loud Speaker, Compact, 300W
Mech. Installation
61339-82273
Section 2.0 ends following the above documents

May 20/15
Sept 14/15

May 20/15
Sept 14/15

May 20/15
Sept 14/15

101.6
4.00
40.6
1.60
66
2.60 PRODUCT LABEL
A A
0.51
177.8
12.8
7.00
3.99
101.3
MAX
44.5
1.75
4X 0.25[6.4] X 0.58[14.8] THRU
C
A
B
C
CONFIDENTIAL AND PROPRIETARY
THE INFORMATION CONTAINED INTHIS DRAWING
WWW.AEM-CORP.COM
NAME DATE
DRAWN
CHECKED
15-1925KIRSCHNERRD.
UNLESS OTHERWISE SPECIFIED: A
D
8
ELECTRONICS MANUFACTURING. ANY
WITHOUT THE WRITTEN PERMISSION OF ANODYNE
ELECTRONICS MANUFACTURING IS PROHIBITED.
KELOWNABCV1Y4N7
6
B
DIMENSIONS ARE IN INCHES [MM]
REPRODUCTION IN PART OR AS A WHOLE
8
APPROVED
7
6
8
6
75
7
5
5
(250)-763-1088
IS THE SOLE PROPERTY OF ANODYNE
0.010"
MATERIAL:
FINISH:
SCALE: 1:2 DRAWING No. : 922-0
PAPER SIZE:
B
TITLE:
CAGE CODE
L9015
LOUD SPEAKER, COMPACT, 150W
MECHANICAL INSTALLATION
TS150 REVISON
1.00
PART No. :
-
N/A
DO NOT SCALE DRAWING
N/A SHEET: 1 OF 1
AJV/DMF 14-Sept-15
8765
TOLERANCES:
FRACTIONAL______________ 0.0625"
ANGULAR_________________ 0.5
TWO DECIMAL PLACE______ 0.020"
THREE DECIMAL PLACE_____
D
NOTES:
MASS 5.5 lbs [2.5 kg] MAX.1. DENOTES CENTER OF GRAVITY (est.)2.
METAL HORN LABEL
8.25 MAX
5.40 MAX
156.5
6.16 MAX
VIEW A-A AEM LABEL
SOUND WARNING LABELS
Sept 14/15
Sept 14/15

May 25/15
Nov 4/15

May 25/15
Nov 4/15

May 25/15
Nov 4/15

May 25/15
Nov 4/15

66
2.60
101.6
4.00
129.5
5.10
AEM LABEL
213.4
8.40 MAX
METAL HORN LABEL
209.6
8.25 MAX
137.2
5.40 MAX
A
C
A
B
THE INFORMATION CONTAINED INTHIS DRAWING
WWW.AEM-CORP.COM
NAME DATE
DRAWN
CHECKED
APPROVED
REPRODUCTION IN PART OR AS A WHOLE
DIMENSIONS ARE IN INCHES [MM]
B
C
D
WITHOUT THE WRITTEN PERMISSION OF ANODYNE
ELECTRONICS MANUFACTURING IS PROHIBITED.
UNLESS OTHERWISE SPECIFIED:
ELECTRONICS MANUFACTURING. ANY
5
15-1925KIRSCHNERRD.
KELOWNABCV1Y4N7
(250)-763-1088
6
CONFIDENTIAL AND PROPRIETARY
8
86
7
8
75
6
7
IS THE SOLE PROPERTY OF ANODYNE
0.005"
MATERIAL:
FINISH:
SCALE: 2:5 DRAWING No. : 922-0
PAPER SIZE:
B
TITLE:
CAGE CODE
L9015
LOUD SPEAKER, COMPACT, 300W
MECHANICAL INSTALLATION
TS300 REVISON
1.00
PART No. :
N/A
DO NOT SCALE DRAWING
N/A SHEET: 1 OF 1
AJV 17-Jun-15
8765 5
TOLERANCES:
FRACTIONAL______________ 0.0625"
ANGULAR_________________ 0.5
TWO DECIMAL PLACE______ 0.010"
THREE DECIMAL PLACE_____
D
4.55
115.6
2.16±0.050
54.91±1.27
231.1
9.10 MAX
28.6
1.13
19.1
0.75
106.7
4.20
133.4
5.25
5X 6.22±0.25
0.245±0.010 THRU MISC PRODUCT LABEL
NOTES:
MASS 9.4 lbs [4.3 kg] MAX.1. DENOTES CENTER OF GRAVITY (est.)2.
A
ug 13/15
A
ug 21/15

TS150/TS300 Loud Speakers
ASM-TS150/TS300 Installation and Operation Manual
Nov 13, 2019 Rev: 1.00 Page 3-1
ENG-FORM: 806-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
Section 3.0 Operation
3.1 Introduction
Information in this section consists of the functional and operational procedures for the TS150 and TS300
Loud Speakers.
3.2 General
The TS150 and TS300 Loud Speakers are lightweight loudspeakers that can be used for both internal and
external aircraft applications. The TS150 and TS300 Loud Speakers are used with the LSA150, LSA300
and LSA400 series amplifiers.
3.3 Operation Specifics
The TS150/TS300 Loud Speakers have no normal user operational aspects.
3.3.1 Cautions
Do not operate the equipment in a hangar or in confined areas without proper hearing protection.
Do not operate the equipment with snow, water or other foreign matter in the loudspeaker horn.
Do not clean the loudspeaker with compressed air.
For continuous tone or siren audio at full output, limit the operation to a 20% duty cycle. One minute
maximum on time followed by 4 minutes off time.
End of Section 3.0