Aeotec ZW062 User manual

View the expanded manual:
http://aeotec.com/support
GEN5
Garage Door Controller

FCC NOTICE (for USA)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED
MODIFICATIONS TO THIS EQUIPMENT.SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE
THE EQUIPMENT.
STORE INDOORS WHEN NOT IN USE. SUITABLE FOR DRY LOCATIONS. DO NOT IMMERSE IN WATER. NOT FOR
USE WHERE DIRECTLY EXPOSED TO WATER.
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation. This
equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
1
2
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consul the dealer or an experienced radio/TV technician for help.
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
Contact your local government for information regarding the collection systems available.
Warning
Certifications (regional):
Z-Wave and Z-Wave Plus are registered
trademarks of Sigma Designs and its
subsidiaries in the United States and other
countries
FCC ID: XBAZW062
CONFORMS TO UL STD.325
CERTIFIED TO CSA STD.CC 22.2 No.247-14
Version: 501006200002-AA www.aeotec.com
13
IN NO EVENT SHALL AEON LABS BE LIABLE FOR ANY INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL OR
CONSEQUENTIAL DAMAGES, OR DAMAGES FOR LOSS OF PROFITS, REVENUE, OR USE INCURRED
BYCUSTOMER, COMPANY OR ANY THIRD PARTY, WHETHER IN AN ACTION IN CONTRACT, OR TORT, OR
OTHERWISE EVENIF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. AEON LABS' LIABILITY AND CUSTOMER'S
EXCLUSIVE REMEDY FOR ANY CAUSE OF ACTION ARISING IN CONNECTION WITH THIS AGREEMENT OR
THE SALE OR USE OF THE PRODUCTS, WHETHER BASED ON NEGLIGENCE, STRICT LIABILITY, BREACH OF
WARRANTY, BREACH OF AGREEMENT, OR EQUITABLE PRINCIPLES, IS EXPRESSLY LIMITED TO, AT AEON LABS'
OPTION, REPLACEMENT OF, OR REPAYMENT OF THE PURCHASE PRICE FOR THAT PORTION OF PRODUCTS
WITHRESPECT TO WHICH DAMAGES ARE CLAIMED. ALL CLAIMS OF ANY KIND ARISING IN CONNECTION WITH
THIS AGREEMENT OR THE SALE OR USE OF PRODUCTS SHALL BE DEEMED WAIVED UNLESS MADE IN WRITING
WITHIN THIRTY (30) DAYS FROM AEON LABS' DELIVERY, OR THE DATE FIXED FOR DELIVERY IN THE EVENT
OF NONDELIVERY. THE INDEMNITY AND WARRANTY IN ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER
INDEMNITIES OR WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Aeotec by Aeon Labs Garage Door Controller.
Aeon Labs Garage Door Controller is a smart and wireless Garage Door Control system, you can control the garage door
to open, close, or stop moving via wireless signal on your gateway client or phone application. You can also control it by
using the external switch when your controller or mobile phone is not on hand.
Its 105dB speaker system will play alarm sounds and at the same time, the indicator of the Garage Door Controller’s Alarm
LED will turn on in which will let you know that the garage door will start to open or close.
The Garage Door Controller allows you to congure different alarm sounds to indicate the door's action. Each action alarm
sound can be customized. To change or update new alarm sounds for the Garage Door Controller, connect the Garage
Door Controller to your PC host with a USB cable and download your sound les to the ash memory (128 MB) of the
Garage Door Controller.
You can also manually switch the alarm sound. To do this, short press the “Button -” or “Button +” button on the Garage
Door Controller which will switch the alarm sound to the next sound. Press and hold the “Button -” or “Button +” to
decrease or increase the volume.
The Garage Door Controller is also a security Z-Wave device and supports the Over The Air (OTA) feature for the product’s
rmware upgrade.
Safety Notes.
®
1
If you are in need of any technical support during or subsequent to your products’ warranty, please get in touch with our
support team via http://aeotec.com/support. The Company you bought this product from has also guaranteed to assist
you with any of your support needs, and you can also contact them for accordingly.
This guarantee made by the company who you purchased the product from includes the transfer of Aeon Labs’ full
warranty to that Company. They’ve guaranteed that they’ll be able to assist you, the Customer, with all technical support
and repair needs on our behalf.
Aeon Labs warrants to the original purchaser of Products, that is the Company who you have purchased from, that for
the Warranty Period (as dened below), the Products will be free from material defects in materials and workmanship. The
foregoing warranty is subject to the proper installation, operation and maintenance of the Products in accordance with
installation instructions and the operating manual supplied. Warranty claims must be made to the Company who you have
purchased from in writing within thirty (30) days of the manifestation of a problem.
Aeon Labs' sole obligation under the foregoing warranty is, at Aeon Labs' option, to repair, replace or correct any such
defect that was present at the time of delivery, or to remove the Products and to refund the purchase price to Company.
The Warranty Period begins on the date the Products is delivered and continues for 12 months. Any repairs under this
warranty must be conducted by an authorized Aeon Labs service representative and under Aeon Labs' RMA policy. Any
repairs conducted by unauthorized persons shall void this warranty.
Excluded from the warranty are problems due to accidents, acts of God, civil or military authority, civil disturbance, war,
strikes, fires, other catastrophes, misuse, misapplication, storage damage, negligence, electrical power problems, or
modication to the Products or its components.
Aeon Labs does not authorize any person or party to assume or create for it any other obligation or liability in connection
with the Products except as set forth herein. Aeon Labs will pass on to Company all manufacturers’ Material warranties to
the extent that they are transferable, but will not independently warrant any Material. Company will assist Customer with
all warranty, repair, return and technical support needs, Company must prepay shipping and transportation charges for
returned Products, and insure the shipment or accept the risk of loss or damage during such shipment and transportation.
Aeon Labs will ship the repaired or replacement products to Company freight prepaid.Customer and Company shall
indemnify, defend, and hold Aeon Labs and Aeon Labs' afliates, shareholders, directors, ofcers, employees, contractors,
agents and other representatives harmless from all demands, claims, actions, causes of action, proceedings, suits,
assessments, losses, damages, liabilities, settlements, judgments, nes, penalties, interest, costs and expenses (including
fees and disbursements of counsel) of every kind (i) based upon personal injury or death or injury to property to the extent
any of the foregoing is proximately caused either by a defective product (including strict liability in tort) or by the negligent or
willful acts or omissions of Customer or its ofcers, employees, subcontractors or agents, and/or (ii) arising from or relating
to any actual or alleged infringement or misappropriation of any patent, trademark, mask work, copyright, trade secret
or any actual or alleged violation of any other intellectual property rights arising from or in connection with the products,
except to the extent that such infringement exists as a result of Aeon Labs' manufacturing processes.
12
Warranty.
61

Package contents:
1. Garage Door Controller.
2. Sensor.
3. 5V DC Adapter.
4. USB Cable.
5. Switch Cable (×2).
6. Screw (×6).
7. Back Mount Plate.
8. Fast Wiring Clip (×2).
9. Double-Sided tape.
Familiarize yourself with your Garage Door Controller.
1
7
8
6
3
9
2
4
5
2
System Operation.
Operation Notes.
1. USE THE MOBILE APPS TO CONTROL YOUR GARAGE DOOR,
VIEW STATUS, AND SET CUSTOM RULES
2. THE GARAGE DOOR CONTROLLER WILL BEEP AND FLASH FOR
FIVE SECONDS BEFORE THE DOOR MOVES
3. THE CONTROLLER WILL ACTIVATE THE DOOR OPENER AND
OPEN OR CLOSE THE DOOR
4. THE MOBILE APP WILL SHOW THE NEW STATUS OF THE DOOR
AFTER THE DOOR COMPLETES ITS CYCLE
1. The Alarm LED will blink and the Speaker System will sound for 5 seconds before the door opener is activated.
STAY CLEAR OF THE DOOR, AND DOOR OPENER. THEY ARE ABOUT TO MOVE!
2. If the door does not completely open or close after remote activation, you need to calibrate the Sensor again. Please
use the “Conguration Parameter 34” to calibrate it. For detailed calibration steps, see the section of 3.4 above.
11
Model number: ZW062
Power supply: 5V DC Adapter for Garage Door Controller. CR2 Lithium battery 3V, 800mA for Sensor.
Max alarm power: 2W.
Max standby power: 1W.
Max volume: 105dB.
Operating temperature: 32°F to 104°F/0°C to 40°C.
Storage temperature: -4°F to 158°F/-20°C to 70°C.
Supported audio format: MP3 or WAV.
Operating distance: Up to 1310 feet/400 meters outdoors.
Technical specifications.
Changes or modications not expressly approved by the manufacturer could void the user’s authority to operate the
equipment.
3. Product is suitable for its own lighting and sound alarm garage door opener, or by UL325 certified door
opener.
The transfer order of MP3 le in the process of copying is also the sequence that will play in Garage Door Controller.
The new added MP3 les will be pushed back to the end of the list in the sequence it is played.
When a MP3 le is renamed in “Removable storage”, it will be moved to the end of the sequence list automatically.
2.
3.
4.
STAY CLEAR OF THE DOOR !!!
2
5

If your primary controller is missing or inoperable, you may wish to reset your Garage Door Controller to its default factory
settings. To do this, press and hold the Z-Wave Button for 20 seconds and then release it. Your Garage Door Controller will
now be reset to its original settings, and the Network LED will be solid for 2 seconds and then start slow blinking to conrm
a success.
Take your Minimote to your Garage Door Controller.
Press the Remove Button on your Minimote.
Press the Z-Wave Button on your Garage Door Controller.
f your Garage Door Controller has been successfully removed from your network, its Network LED will blink. If the
removal was unsuccessful, the Network LED will not blink.
Press any button on your Minimote to take it out of removal mode.
Reset your Garage Door Controller.
Use the Micro USB cable to connect Garage Door Controller to your PC host. PC host will detect the removable
storage after a few seconds and then you will nd it in the section of “Device with Removable Storage”.
Double click the “Removable Disk (G:)” to open it.
Now you can copy/drag the new alarm sounds from the PC hard disk to the Garage Door Controller’s ash memory.
Wait a few minutes to complete the copying.
Do not disconnect the USB port until copying has completed.
This procedure should only be used when the complimentary Sensor is missing or inoperable and you have another new
Sensor that would be paired with your Garage Door Controller. To do this, press and hold the Switch Button for 5 seconds,
the Network LED will fast blink, which indicates it has entered into pairing mode, at this time, press the Temper Switch of
Sensor once, your Sensor should now be paired with the Garage Door Controller.
1.
2.
3.
4.
1.
2.
3.
4.
5.
6.
7.
1.
1.
2.
3.
4.
5.
Note:
Download new ringtones to your Garage Door Controller from PC host.
Pair the Sensor with your Garage Door Controller.
If you’re using a Minimote:
10
Quick start.
Power on your Garage Door Controller.
Add/include your Garage Door Controller to a Z-Wave network.
Power your Garage Door Controller by connecting the 5V DC Adapter to the input.
Now that your Garage Door Controller is powered on, you will see the Network LED blinking slowly. While the Network
LED is blinking, this indicates that the Garage Door Controller is ready to be included into a Z-Wave network.
The following instructions will tell you how to add your Garage Door Controller to your Z-Wave network via an Aeon Labs’
Z-Stick or Minimote controller. If you are using another Z-Wave controller as your main controller, please refer to their
respective manual on how to add new devices to your network.
If you’re using a Z-Stick:
Connect 5V DC Adapter to the Garage Door Controller. Its Network LED will begin to blink.
If your Z-Stick is plugged into a gateway or a computer, unplug it.
Take your Z-Stick to your Garage Door Controller.
Press the Action Button on your Z-Stick.
Press the Z-Wave Button on the Garage Door Controller.
If Garage Door Controller has been successfully added to your Z-Wave network, its Network LED will be solid for 2
seconds and then be off. If the adding was unsuccessful and the Network LED continues to blink, repeat the steps
above.
Press the Action Button on the Z-Stick to take it out of inclusion mode.
3
Note: When the Garage Door Controller enters into pairing mode, it has 8 seconds before timeout for pairing.
3

Physically install your Garage Door Controller.
If you’re using a Minimote:
WARNING — TO REDUCE THE RISK OF SEVERE INJURY OR DEATH:
6. LOCATE CONTROL BUTTON
a) WITHIN SIGHT OF DOOR;
b) AT A MINIMUM HEIGHT OF 1.53 M (5 FT) SO
SMALL CHILDREN CANNOT REACH IT; AND
c) AWAY FROM ALL MOVING PARTS OF THE DOOR.
6. INSTALLEZ LE BOUTON DE COMMANDE
a) À UN ENDROIT QUE L’ON PEUT VOIR DE
L’EMBRASURE DE LA PORTE;
b) À UNE HAUTEUR MINIMALE DE 1,53 M (5 PI) DU
SOL — AFIN QUE LES JEUNES ENFANTS NE PUISSENT
PAS L’ATTEINDRE ; ET
c) À L’ÉCART DES PIÈCES MOBILES DE LA PORTE.
The Garage Door Controller must be installed in your home and near the garage door. It cannot be installed outdoors in
elements such as rain and snow.
Connect 5V DC Adapter to the Garage Door Controller. Its Network LED will begin to blink.
Take your Minimote to your Garage Door Controller.
Press the Include button on your Minimote.
Press the Z-wave Button on your Garage Door Controller.
If Garage Door Controller has been successfully added to your Z-Wave network, its Network LED will be solid for 2
seconds and then be off. If the adding was unsuccessful and the Network LED continues to blink, repeat the steps
above.
Press any button on your Minimote to take it out of inclusion mode.
4
The following instructions will tell you how to remove your Garage Door Controller from your Z-Wave network via an Aeotec
by Aeon Labs’ Z-Stick or Minimote controller. If you are using another Z-Wave controller as your main controller, please
refer to their respective manual on how remove devices from your network.
If you’re using a Z-Stick:
If your Z-Stick is plugged into a gateway or a computer, unplug it.
Take your Z-Stick to your Garage Door Controller.
Press and hold the Action Button on your Z-Stick for 3 seconds and then release it.
Press the Z-Wave Button on your Garage Door Controller.
If your Garage Door Controller has been successfully removed from your network, its Network LED will blink. If the
removal was unsuccessful, the Network LED will not blink.
Press the Action Button on the Z-Stick to take it out of removal mode.
Removing your Garage Door Controller from a Z-Wave network.
Advanced functions.
IMPORTANT SAFETY INSTRUCTIONS.
WARNING — TO REDUCE THE RISK OF SEVERE
INJURY OR DEATH:
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. NEVER LET CHILDREN OPERATE OR PLAY
WITH DOOR CONTROLS. KEEP REMOTE
CONTROL AWAY FROM CHILDREN.
3. ALWAYS KEEP MOVING DOOR IN SIGHT AND
AWAY FROM PEOPLE AND OBJECTS UNTIL IT IS
COMPLETELY CLOSED. NO ONE SHOULD CROSS
THE PATH OF THE MOVING DOOR.
4. SAVE THESE INSTRUCTIONS.
IMPORTANT — MESURES DE SÉCURITÉ
AVERTISSEMENT — POUR RÉDUIRE LES RISQUES DE
BLESSURES MORTELLES
1. LISEZ CETTE NOTICE ET CONFORMEZ-VOUS AUX
MISES EN GARDE
2. NE LAISSEZ JAMAIS LES ENFANTS MANOUEVRER
LES COMMANDES DE LA PORTE. NE LAISSEZ PAS LA
TÉLÉCOMMANDE À PORTÉE DES ENFANTS.
3. SURVEILLEZ LA COURSE DE LA PORTE JUSQU’À CE
QUE CETTE DERNIÈRE SOIT COMPLÈTEMENT
FERMÉE EN VEILLANT À TENIR À L’ÉCART TOUTE
PERSONNE ET TOUT OBJET AVOISINANT. IL NE FAUT
JAMAIS PASSER EN-DESSOUS D’UNE PORTE EN
MOUVEMENT.
4.CONSERVEZ CES INSTRUCTIONS.
9
4
1.
2.
3.
4.
5.
6.
1.
2.
3.
4.
5.
6.
With your Garage Door Controller now working as a part of your smart home, you’ll be able to congure it from your home
control software or phone application. Please refer to your software’s user guide for precise instructions on conguring
Garage Door Controller to your needs.
The speaker system is 105dB and you can reduce its volume via long pressing the “Button-” or increase the volume via
long pressing the “Button -”. When the “Button -” or “Button +” is pressed, the default Garage Door Controller alarm sound
will be triggered. To switch to the next alarm sound, short press the “Button -” or “Button +”.

2. Connect the 2 Switch cables to the Switch Connector 1 and 2 on the Garage Door Controller, and then use the Fast
Wiring Clip to connect the 2 Switch Cables to the Motor Switch Cables, see the gure below:
Note: The Fast Wiring Clip need to be used with pliers. When the Switch Cable and the Motor Switch Cable have been
connected by Fast Wiring Clip, you will need to use the pliers to clamp the Fast Wiring Clip, see the gure above.
3. Now lock the Garage Door Controller to the Back Mount Plate by twisting the Garage Door Controller.
1. Utilize the provided 20mm screws to afx it to the desired surface.
5
After completing all installation steps, you may need to test your Garage Door Controller to see if it has been successfully
installed. You can implement this via short pressing the Switch Button on the Garage Door Controller. When you press
the Switch Button, you will see the alarm LED blink and ring the alarm sound. After about 5 seconds, the garage door will
move to a full open or closed position. If you press the Switch Button again, the garage door will immediately stop moving.
If not, please check or repeat the steps above.
Note: If you have conrmed the installation is successful, you need to calibrate the Sensor once.
For detailed calibration steps, please refer to the “Conguration Parameter 34” as below:
Parameter 34[1 byte dec] can be congured through your gateway or controller.
Calibration Steps:
1. Let the garage door move to full close position via sending control commands or pressing manual Switch.
2. Send this parameter (34) with “value=1” to Garage Door Controller through your gateway/controller.
3. Let the garage door move to full open position via sending control commands or pressing manual Switch.
4. Let the garage door move to full close position via sending control commands or pressing manual Switch after the step
3 has completed.
After the step 4 has completed, all calibration steps are complete.
8
Note: 1. Installation location higher than 5 feet.
2. Ensure that the distance between the
Sensor and Door Controller is less than 30 feet.

1. Press and hold the Latch Button to unlock the sensor mounting plate:
2. Pull out the insulating sheet, then you will see the Sensor LED blink once to indicate it has been powered on.
Installing the Sensor on your garage door.
Press and hold the Latch Button
6
3. Afx your sensor mounting plate to the garage door.
The sensor mount plate should be installed on the top of the garage door (on the left, middle, or right side). Now afx your
sensor mounting plate to the surface. Your mounting plate can be afxed using screws or double-sided tape.
If you are using screws, attach the mounting plate to the respective surface using the two 20mm screws provided.
Insulating sheet
If you are using double-sided tape, wipe the two surfaces clean of any oil or dust with a damp towel. When the surface
has completely dried, peel one side of the tape back and attach it to the corresponding section on the rear side of the
mounting plate.
You can choose each of way from these 2 installations above. Just need to note if the environment temperature of the
garage door is less than -5 , we suggest to choose the rst way (using screws to afx the mounting plate) that would be
more stable.
4. Lock your Sensor on the mounting plate.
Press and hold the Latch Button, and then push the Sensor into the mounting plate.
C
7