AEROMAT NH35 User manual

Thank you for purchasing this AEROMAT watch. The following
instructions are provided to help familiarize yourself with the
proper operation and care of your AEROMAT watch. To
ensure correct use, please read and follow the instructions
carefully.
01

02
CONTENT
P3
P4
P5
P6
P7
P8
P9-10
P11-12
P13
P14
P15-16
AUTOMATIC
NH35 - Type B
NH37 - Beluga
- Beluga - Function
9015 - Super Sonic
- Super Sonic - Function
8215 - Type A
QUARTZ
VK63 - Vol de Nuit
VK64 - PNY
763 - AEM450
515.24H - Type GMT
PRECAUTIONS AND PREVENTIVE MEASURES

03
AUTOMATIC - NH35
WIND UP THE MAINSPRING
SETTING THE DATE
SETTING THE TIME
Push the crown back to the position.
Pull the crown out to the position.
Normal position
1.
2.
3.
4.
Crown may need to be unscrewed
prior to operation.
Turn the crown to set hour and
minute hands
Pull the crown out to the position.
Push the crown back to the position.
Normal position
1.
2.
3.
4.
Turn the crown counter-clockwise
to set the date
Do not set the date between
9:00PM and 4:00AM as this
may cause a malfunction.
Normal position1.
2. Turn the crown clockwise to wind
up the mainspring
Wind by turning the crown clockwise
8 times. It will start to move naturally
after shaking slightly.
To wind up with winding machine.
Full wind up conditions:
Rotary speed: 30rpm
Operating time: 60rpm

04
AUTOMATIC - NH37
WIND UP THE MAINSPRING
SETTING THE DATE
SETTING THE TIME
Normal position1.
2.
3.
4.
Turn the crown to set hour and
minute hands
Crown may need to be unscrewed
prior to operation.
Push the crown back to the position.
Pull the crown out to the position.
Normal position1.
2.
3.
4.
Turn the crown counter-clockwise
to set the date
Do not set the date between
9:00PM and 4:00AM as this
may cause a malfunction.
Pull the crown out to the position.
Push the crown back to the position.
Normal position1.
2. Turn the crown clockwise to wind
up the mainspring
Wind by turning the crown clockwise
8 times. It will start to move naturally
after shaking slightly.
To wind up with winding machine.
Full wind up conditions:
Rotary speed: 30rpm
Operating time: 60rpm
Some models will remove the date function.

05
BELUGA - FUNCTION
HOW TO TURN THE COUNTDOWN BEZEL
The countdown bezel can determine the remaining time.
1. Turn the bezel and align the bezel’s zero position with
the targeted time.

06
AUTOMATIC - 9015
WIND UP THE MAINSPRING
SETTING THE DATE
SETTING THE TIME
Normal position1.
2. Turn the crown clockwise to wind
up the mainspring
Wind 15 ~20 times clockwise until
second hand starts to move naturally.
Normal position1.
2.
3.
4.
Turn the crown counter-clockwise
to set the date
Do not set the date between
8:30PM and 2:00AM as this
may cause a malfunction.
Pull the crown out to the position.
Push the crown back to the position.
Normal position1.
2.
3.
4.
Turn the crown to set hour and
minute hands
Crown may need to be unscrewed
prior to operation.
Push the crown back to the position.
Pull the crown out to the position.

07
SUPER SONIC - FUNCTION
HOW TO TURN THE INNER RING
1. Turn the 2H crown clockwise or counter-clockwise
to set the inner ring

08
AUTOMATIC - 8215
WIND UP THE MAINSPRING
SETTING THE DATE
SETTING THE TIME
Normal position1.
2. Turn the crown clockwise to wind
up the mainspring
Wind 15 ~20 times clockwise until
second hand starts to move naturally.
Normal position1.
2.
3.
4.
Turn the crown counter-clockwise
to set the date
Pull the crown out to the position.
Push the crown back to the position.
Normal position1.
2.
3.
4.
Turn the crown to set hour and
minute hands
Crown may need to be unscrewed
prior to operation.
Push the crown back to the position.
Pull the crown out to the position.

09
QUARTZ - VK63
SETTING THE DATE
Normal position1.
2.
3.
4.
Do not set the date between 9:00PM
and 3:00AM; otherwise the date may
not change properly. If it is necessary
to set the date during that period,
first change the time to any time
outside it, set the date, and then
reset the correct time.
Turn the crown counter-clockwise to
set the date
Pull the crown out to the position.
Push the crown back to the position.
Normal position1.
2.
3.
4.
If the crown is pulled to the second position
while the chronograph has started, the
chronograph hands will continue to move.
This is not a malfunction.
Turn the crown to set hour and
minute hands
(Check that AM / PM is set correctly)
Crown may need to be unscrewed prior to
operation.
Push the crown back to the position.
Pull the crown out to the position.
SETTING THE TIME

10
QUARTZ - VK63
HOW TO USE THE CHRONOGRAPH
Press button to start the chronograph.
The chronograph hands will start moving
1.
2.
3.
Press button again to stop the
chronograph. The chronograph hands stop
to indicate the elapsed time
Press button to reset the chronograph.
All the chronograph hands will be reset
to "0" position
The chronograph can measure up to 60 minutes
and stops after a measurement for 60 minutes.
Normal position1.
2.
3.
4.
If the crown is operated within the 10 seconds,
the two-second intervals movement will not be
activated.
5. The small second hand will move at two-second
intervals for 10 seconds as a demonstration
Press the button for two seconds and
release the button
Push the crown back to the position.
Pull the crown out to the position.
RESET

11
QUARTZ - VK64
SETTING THE DATE
Pull the crown out to the position.
Normal position
1.
2.
3.
Push the crown back to the position.
4.
Do not set the date between 9:00PM
and 3:00AM, otherwise the date may
not change properly. If it is necessary
to set the date during that period,
first change the time to any time
outside it, set the date, and then
reset the correct time.
Turn the crown counter-clockwise to
set the date
SETTING THE TIME
Normal position1.
2.
3.
4.
If the crown is pulled to the second position
while the chronograph has started, the
chronograph hands will continue to move.
This is not a malfunction.
Turn the crown to set hour and minute hands
(Check that AM / PM is set correctly)
Crown may need to be unscrewed prior to
operation.
Push the crown back to the position.
Pull the crown out to the position.

12
QUARTZ - VK64
Press button to start the chronograph.
The chronograph hands will start moving
1.
2.
3.
Press button again to stop the
chronograph. The chronograph hands stop
to indicate the elapsed time
Press button to reset the chronograph.
All the chronograph hands will be reset
to "0" position
The chronograph can measure up to 60 minutes
and stops after a measurement for 60 minutes.
HOW TO USE THE CHRONOGRAPH
Normal position1.
2.
3.
4.
It is not necessary to set the chronograph
hands after the battery is exchanged. If the
chronograph hand positions are incorrect,
follow below procedure, all the chronograph
hands will be reset to "0" position.
Press the button for two seconds and
release the button
Push the crown back to the position.
Pull the crown out to the position.
RESET

13
QUARTZ - 763
SETTING THE TIME
Normal position1.
2.
3.
4.
Turn the crown to set hour and
minute hands
Crown may need to be unscrewed
prior to operation.
Pull the crown out to the position.
Push the crown back to the position.

14
QUARTZ - 515.24H
SETTING THE DATE & 24-Hour Hand
Normal position1.
2.
3.
4.
Turn the crown clockwise to set the date.
Turn the crown counterclockwise to set
the 24-hour hand
Pull the crown out to the position.
Push the crown back to the position.
SETTING THE TIME
Normal position1.
2.
3.
4.
Turn the crown to set hour and minute
hands
(Check that AM / PM is set correctly)
Crown may need to be unscrewed
prior to operation.
Push the crown back to the position.
Pull the crown out to the position.

15
PRECAUTIONS AND PREVENTIVE MEASURES
Temperature
Do not expose your watch to sudden
temperature changes (exposure to
sunlight followed by immersion in cold
water) or extreme temperatures
[over 60°C (140°F) or below 0°C (32°F)].
Shocks
Avoid thermal or other shocks as it
may harm your watch. In the event of
a violent shock please have your
watch checked by a reputable jeweler
or service center.
Harmful Products
Avoid direct contact with solvents,
detergents, and perfumes, cosmetic
products, etc. since they may damage
the bracelet, the case and/or the
gaskets.
Care and Checks
Clean the case and bracelet regularly
using a soft cloth to prevent any
corrosion caused by perspiration. All
water resistant watches can be cleaned
with a toothbrush and soapy water, and
then dried with a soft cloth. After being
worn in the sea, the watch must be
rinsed with warm fresh water, and then
dried completely.
Replacing the Battery
(For Quartz watches only)
We recommend you take the watch to
a reputable jeweler or watch repair
facility who is equipped with the tools
and apparatus required to carry out
the work and the necessary checks in
a professional manner. A worn-out
battery should be replaced immediately
in order to reduce the risk of leakage
and consequent damage to the
movement.

16
PRECAUTIONS AND PREVENTIVE MEASURES
Water Resistance
1. [3atm / 30m / 100ft]
Watches water resistant to
30 meters /100 feet.
2. [5atm / 50m / 165ft]
Watches water resistant to
50 meters /165 feet.
3. [10atm / 100m / 330ft]
Watches water resistant from
100 meters / 330 feet or more
with screw down crown and
diving bezel.
According to the water resistance 1, 2 or 3
listed above, watches are protected against:
1-2-3
2-3 Shower/ Free diving / Water sports
Water splashes / Rain
Limited Warranty
Your AEROMAT watch is warrantied
by AEROMAT for a period of twenty
four (24) months from the date of
purchase under the terms and conditions
of this warranty. The international
AEROMAT warranty covers material
and manufacturing defects. The warranty
only becomes active if the warranty
certificate is dated, fully and correctly
completed. In the event that repairs
are improper to restore the
normal
conditions of use of your AEROMAT
watch, AEROMAT guarantees its
replacement by an AEROMAT watch of
identical or similar characteristics. The
warranty for the replacement watch is
TWENTY FOUR (24) MONTHS after the
date the replacement is issued.
This manufacturer’s warranty does not
cover:
1. The life of the battery
2. Wear and tear and aging (e.g. scratched
crystal; alteration of the color and/or
material of non metallic straps and
chains, such as leather, textile, rubber;
peeling of the plating).
3. Any damage on any part of the watch
resulting from abnormal/abusive use,
lack of care, negligence, and accidents
(nicks, dents, crushing, broken crystal,
etc.). Incorrect use of the watch and
non-observance of the use directions
provided by AEROMAT. The AEROMAT
watch not handled by a reputable
jeweler or service center (e.g., for
battery replacement, services or repairs)
or which has been altered in its original
condition beyond AEROMAT’s control.