AEROMODELIS SENSE F5J User manual

SENSE F5J (by aeromodeli.lt)
Sense building manual (v1.0)
Congratulations and thank you for choosing the model! Please check that all
items ordered are included and not damaged during transportation.
The Sense kit already is well prepared for your assembly and has following
features pre-installed:
•Ballast chamber
•Tail group linkages
•Servo pockets with carbon reinforcement and roads channels
•Servo wiring with soldered MPX connectors ( fuselage, wing)
The Sense kit contains following parts:
•1.5 mm wire for top drive linkage (flaps and ailerons)
•Servo tray for fuselage servos
•Servo horns (5ps )
•Screws for wing and tail group
•4 small roads for central and outer wing panels alignment

•4 servo pockets covers
•2 fuselage servo clevis couplers
•2 paars of wing joiners 5.5 and 7 degrees
Optional Parts:
•Ballast Set (normal or heavy)
•Premium wing covers
•3D printed aileron top drive servo frames
•Flaps servo frames (servorahmen.de)
•CNC Aluminium motor mount (Powerline, reisenauer gbox, Mega)
•30 mm VM Pro Spinner
•Propellers: 11x6.5, 12x7.5, 13x7, 13x8, 13.5x8, 13x9
Assembling
Fuselage
You need to prepare servo tray to fit your fuselage servos for elevator and rudder. The
tray is designed for two KST xt08 servos, but you can fit bigger ones like MKS6100.
Install the tray as close as possible to ballast chamber (10 mm from chamber is good)
to have more room in the fuselage.
Glue the tray with long time epoxy, do not glue middle part, it holds with 4 screws for
swapping servos or placing receiver.
Glue the 2mm clevis couplers to the pushrods (install elevator and rudder for correct
length adjustment.

Glue Motor mount with epoxy. Make sure
you have motor’s wire on side of
fuselage.

Glue all connectors after it connected to receiver and everything works as designed
Wing connector must be fixed after the fuselage connector is glued.
Ballast assembling.
Glue two halves on ballast ends .

Rudder connector is already made on the fabric.
Cut a slot for the rudder horn.

Glue it with expoxy.
Make sure it fits under fuselage covering

Wing assembling (Flaps section).
We advise to install all servos in servo frames. You can choose LDS or top drive installation
(this manual).
The wing already has a molded channel for servo rods. Cut slot for horns as on the
pictures
Check that the flap servo arms are set 90 degrees on the servo and that the transmitter also
is set to neutral or use servo tester to set neutral position.
Before glue servo frame with servo installed make sure flaps have offset about 18-20
degrees down and equal for left and right of the wing.
Glue servo horns only with epoxy.

The length of the roads 76-78 mm
It makes 18-20 degree of down flaps

Install balsa patch to preoctec rods from loose during the moving

Ailerons servo installation
Prepare rods with a shape described below.
Check that the aileron servo arms are set 90 degrees on the servo and that the transmitter
also is set to neutral or use servo tester to set neutral position.
Glue servo horns only with epoxy

Sense Settings (-up, +down, ° degrees)
CG 100-107 mm, we recommend to start with 103 mm.
For windy or turbulent conditions move CG forward a little, for late evening or
flat conditions move CG slightly back.
Flying light Sense in an active air, we recommend to move CG forward as well.
Our rule of thumb: a heavier Sense likes more camber!
!
!
Flight'Mode'
Ailerons'
Flaps'
Elevator'
Fast!Cruise!
0!
0!
!
Cruise!
+0.7!
+0.7!
!
Speed!
-1.5!
-1.5!
!
Thermal!1!
+2.5!
+2.5!
!
Thermal!2!
+4!
+4!
!
Thermal!Range!
+2-5!
+2-5!
!
!
Surfaces'
Aileron'
Flap'
Elev'
Rudder'
Note'
SnapFlap,!Elevator!
full!UP!
+4!
+4!
-10!
!
!
SnapFlap,!Elevator!
full!DOWN!
-1.5!
-2!
+9.5!
!
Optional!
Ailerons!full!UP!
-19!
-6!
!
5!
Ail-Rud!!is!optional!
(not!for!thermal!
mode)!
Ailerons!full!Down!
+17!
+7!
!
!
!
Breaks!/!Crow!
-5!
+70!
+8!
!
!
Max!Rudder!
!
!
!
16!
!
!
'
Using'Ballast'
'
Sense is very sensetive on a weight change. Some recommendations:
Wind'speed'(m/s)'
Weight'(gr.)'
!
2-4!
1100-1300!
!
4-7!
1300-1700!
!
7-12!
1700-2100!
!
WARNING. The ballast tube does not have a stopper in the rare part, so if
you want to use more than 10 chunks of ballast, wrap the last chunks with a
tape to prevent them from rotation and possible jamming in the tube.
'
'
!