The World Models Manufacturing SUPER STUNTS User manual

Wing Span
Wing Area
Flying Weight
Fuselage Length
66.5 in / 1690 mm
882 sq in / 56.9 sq dm
57.0 in /1450 mm
5.5 lbs / 2500 g
Specifications
INSTRUCTION MANUAL
0.40-0.46 cu in displacement 2-stroke. .
Requires : 4-channel radio w/ 5 standard servos
Warning !This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of engine powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
* Specifications are subject to change without notice.*
The World Models
Manufacturing Co., LTD.
www.theworl dm odels.com
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
FACTORY PRE-FABRICATED
E
A
D
R
-
Y
T -
T
S
O
O
-
F
M
L
L
Y
A
A095PO25881103

P.1
Apply thread locker
Apply epoxy glue.
Pierce the shaded portion
covering film.
Apply instant glue
(C.A.glue, super glue.)
Ensure smooth non-bindin g
movement while assembling.
Do not overlook this symbol !
P. 3 -10
Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT
and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you
find to be defective after the gluing process may be difficult to remove for warranty replacement. The
manufacturer will replace any defective parts, but will not extend to the parts that are good before
gluing to defective parts during assembly. Warranty will not cover any parts modified by customer.
INDEX
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
P. 1
P. 2
P.10
BEFORE YOU BEGIN
Read through the manual before you begin, so you will have an overall idea of what to do.
Symbols used throughout this instruction manual comprise of the following : -
1
2
3
Assemble left and right
sides the same way.
Peel off shaded portion
covering film.
Drill holes with the specified
diameter (here: 3mm) .
Pay close attention here!
Cut off shaded portion.
Must be purchased separatel y !
Warning!
3mm
A095PO25881103

Parts List
P.2
LIGHTEX:--
LIGHTEX SGX 100 WHITE
LIGHTEX SGX 201 BLACK
LIGHTEX SGX 311 FERRARI RED
LIGHTEX SGX 330 CADMIUM YELLOW
LIGHTEX SGX 351 DARK BLUE
1. MAIN WING -- 1 pair
2. SCREW PB2x12mm -- 4 pcs
FUEL TUBE Ø6x5mm -- 4 pcs
STRAPER PL4112102 -- 2 pcs
CLEVIS (L) PL4112103 -- 2 pcs
HORN (L) PL4113101 -- 2 sets
PUSHROD Ø1.8x175mm w/ Threads (For Aileron) -- 2 pcs
3. WING JOINER 5.8x28.5x90mm -- 1 pc.
4. FUSELAGE -- 1 pc.
STABILIZER & ELEVATOR -- 1 set
BALSA(Fin Tip) 6x54.4x223.5mm -- 1 pc.
5. VERTICAL FIN & RUDDER -- 1 set
6. FUEL TANK 320cc PL1111320 -- 1 set
CABLE TIE 1.5x5x400mm -- 1 pc.
DOUBLE-SIDED 40x100mm -- 1 pc.
7. SOCKET HEAD SCREW M4x25mm -- 4 pcs
WASHER d4xD9mm -- 4 pcs
ENGINE MOUNT PL5111050 -- 1 set
8. FRONT LANDING GEAR -- 1 set
FRONT WHEEL Ø65mm -- 1 pc.
COLLAR Ø4.1mm w/ set screw -- 2 sets
STEERING ARM Ø4.1mm w/ set screw -- 1 set
FRONT WHEEL PUSHWIRE Ø1.6x410mm -- 1 pc.
PLASTIC TUBE d2.5xD4x340mm -- 1 pc.
WOOD 7.5x7.5x18mm (For Front Landing Gear) -- 1 pc.
9. MAIN LANDING GEAR -- 1 set
SCREW PA3x12mm -- 4 pcs
MOUNTING PLATE 12x20mm -- 2 pcs
10. MAIN WHEEL Ø65mm -- 2 pcs
COLLAR Ø4.1mm w/ set screw -- 4 sets
11. ALUMINUM PLATE 1mm -- 1 pc.
SCREW PM2x10mm -- 4 pcs
WASHER d2xD5mm -- 4 pcs
M2 NUT -- 4 pcs
SOCKET HEAD SCREW M3.5x30mm -- 4 pcs
WASHER d3.5xD8mm -- 8 pcs
M3.5 NUT -- 8 pcs
SPINNER Ø57mm PL2111057 -- 1 set
THROTTLE PUSHWIRE Ø1.2x340mm -- 1 pc.
PLASTIC TUBE d2xD3x180mm -- 1 pc.
12. SCREW PM2x16mm -- 2 pcs
M2 NUT -- 2 pcs
FUEL TUBE Ø6x5mm -- 2 pcs
CLEVIS (L) PL4112102 -- 2 pcs
HORN (Non-Base) (For Rudder) (L) PL4113101 -- 2 sets
RIGGING COUPLER Ø1.8x27mm w/ Threads (For Rudder) -- 2 pcs
COPPER TUBE d2.5xD3.2x8mm (For Rudder Servo) -- 2 pcs
WIRE Ø1x860mm (For Rudder) -- 2 pcs
13. SCREW PB2x16mm -- 2 pcs
FUEL TUBE Ø6x5mm -- 1 pc.
HORN (L) PL4113101 -- 1 set
CLEVIS (L) PL4112103 -- 1 pc.
PUSHROD Ø1.8x760mm w/ Threads (For Elevator) -- 1 pc.
14. PLYWOOD 6x62x96.4mm (For Rudder Servo) -- 1 pc.
BALSA 5x5x62mm (For Rudder Servo Stand) -- 2 pcs
PLYWOOD 6x42x96mm (For Elevator Servo) -- 1 pc.
BALSA 6x6x42mm (Fro Elevator Servo Stand) -- 2 pcs
PLYWOOD 6x62x98.3mm (For Throttle Servo) -- 1 pc.
BALSA 5x5x62mm (For Throttle Servo Stand) -- 2 pcs
15. LINKAGE CONNECTOR Ø2.1mm -- 2 sets
16. SPONGE 60x70x94mm (For Radio Equipment) -- 1 pc.
STRAPER PL4112102 -- 1 pc.
RIGGING Z BEND Ø1.8x27mm (For Rudder) -- 2 pcs
COPPER TUBE d2.5xD3.2x8mm -- 2 pcs
FUEL TUBE Ø6x5mm -- 1 pc.
17. SCREW HM4x35mm -- 2 pcs
WASHER d4xD12mm -- 2 pcs
PLYWOOD 3x30x97mm (Wing Protection) -- 1 pc.
18. DECALS: A095DEC -- 1 set
A095PO25881103

P.3
Wing Joiner
90 x 28.5 x 5.8mm
Main Wing
1
Aileron & Flap Servos
2
Main Wing
3
Apply instant type CA glue to both sides of each hinge.
Please dry fit wing joiner into left and right wing to make sure they fit
with the proper dihedral angle, mark the wing joiner if necessary.
Apply epoxy glue to both sides of all surfaces in contact. Use a stick
to apply the glue to inner side of wing joiner sleeve, and apply the
glue to wing joiner before putting them together. Wing joiner not
glued properly will lead to wing failure and plane crash.
Ø1mm pilot holes for World Models horn are
pre-drilled. Please look for pin-hole marks at
under side of control surfaces.
Straper
Pushrod
Ø1.8 x 175mm
Fuel Tube
Ø6 x 5mm
PB2 x 12mm
Clevis
Horn
Lead for servo
wire provided
PB2x12mm Screw
4
1mm
Bottom View
TWM Pl82 1001 0
CLEVIS WRENCH
A095PO25881103

Bottom View
A A
A=A
4
5
(Stabilizer)
(Main Wing)
B B'
B=B'
Apply instant type CA glue to both sides of
each hinge.
Apply instant type CA glue to both sides
of each hinge.
C=C
C C
P.4
A A
A=A
Temporary install the main wing,
adjust leveling of the stabilizer to
make it as para llel to the main wing
as possible.
Stabilizer & Elevator
Vertical Fin & Rudder
BALSA(Fin Tip)
6x54.4x223.5mm
A095PO25881103

P.5
Fuel Tank
320cc
Fuel Tank
6
UP
Engine Mount
PL 5111-050
d4xD9mm Washer
4
4
M4x25mm Socket Head Screw
Engine Mount
7
M4x25mm
d4xD9mm
Washer
Engine Mount
PL5111050
Blind nuts are off-centered to keep
the spinner at the fuselage axis.
Apply thread locker to screws
3mm Set Screw
3mm Set Screw
8
23mm Set Screw
4.1mm Collar
4.1mm Collar
Front Landing Gear
PLYWOOD
7.5 x 7.5 x 18mm
Cable Tie
1.5x5x400mm
40x100mm
Double-sided Tape
Completed
A095PO25881103

Aluminum Plate 1mm
PM2x10mm
d2xD5mm Washer
Spinner
Ø57mm
M2 NUT
PA 3 x 12mm
Wheel 65mm
Main Landing Gear
4mm
4.1mm Collar
3mm Set Screw
9
10
P.6
2mm
PA3x12mm Screw
4
4
4.1mm Collar
Main Landing Gear
Main Wheels
Engine
11
PM2x10mm Screw
Installed Engine Position
Spinner
52mm
118mm
4.65 in.
d3.5xD8mm Washer
d2xD5mm Washer
M3.5 Nut
Completed
M3.5x30mm
d3.5xD8mm
Washer
M3.5 Nut
M3.5x30mm Socket Head Screw
Mounting Plate 12x20mm
A095PO25881103

P.7
Elevator Pushrod
13
Pushrod Pushwire
12
PM2x16mm Screw
2
2
Ø1mm pilot holes for World Models horn are
pre-drilled. Please look for pin-hole marks at
under side of control surfaces.
PM2x16mm
Copper Tube
d2.5xD3.2x8mm
Fuel Tube
Ø6x5mm
2mm
PB2x16mm Screw
2
Ø1mm pilot holes for World Models horn are
pre-drilled. Please look for pin-hole marks at
under side of control surfaces.
Bottom View
PB2x16mm
Horn
Elevator Pushrod
Ø1.8x760mm
Plywood
6x62x98.3mm
Plywood
6x62x96.4mm
Plywood
6x42x96mm
Balsa
6x6x42mm
Balsa
5x5x62mm
Balsa
5x5x62mm
14 Servos
TWM Pl82 1001 0
CLEVIS WRENCH
TWM Pl82 10010
CLEVIS WRENCH
Horn
Wire
1x860mmØ
A095PO25881103

P.8
3 X 3mm Set Screw
2mm Nut
Linkage Connector
2
2
2
4
2mm Washer
Servo Set
15
Throttle Pushwire
3mm
Throttle Servo.
M2 Nut
Please refer to attached sheet for linkage connector installation.
Clamp the copper tube
Throttle Servo Rudder Servo
Elevator Servo
Straper
Fuel Tube
Ø6x5mm
Sponge
Receiver
Battery
Front
Front Wheel Pushrod Elevator Pushrod
Rigging Coupler
Ø1.8x27mm
Copper Tube
d2.5xD3.2x8mm
Radio Equipment
16 Install and arrange the servo as shown in the diagram.
HM4x35mm Screw
D4xD12mm Washer
2
2
HM4x35mm
d4xD12mm
Washer
Wing Protection
3x30x97mm
4mm
Main Wing
17
2mm
Washer
2mm
2mm
Washer
Charge Receptacles
KP0041300
A095PO25881103

P.9
A=A
B=B
Elevator
Rudder
Aileron
15mm
15mm
40mm
40mm
10mm
Wing Setting
18
Control Throws
19
Adjust the wing and fuselage configuration as shown in
the diagrams.
Adjust the control throws as shown in the
diagram. These throws are good for general
flying. You can adjust according to your
personal preference.
C.G.
The ideal C.G. position is 105mm (4.13 in.)
behind the leading edge measured at
where the wing meets the fuselage. In
order to obtain the C.G. specified, add
weight to the fuselage or move the battery
position. Check the C.G. before flying.
C. G.
20
105 mm
4.13 in.
C.G.
A095PO25881103

P.10
Important Safety Precautions
# First time flyer should never fly by himself / herself. Assistance from experienced
flyer is absolutely necessary.
# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly
pre-adjusted aircraft.
# is specially designed to be powered by 2C engine, using a
powerful engine does not mean better performance. In fact, over powered engine
may cause severe damage and injuries.
# Make sure the air field is spacious, never fly the plane too close to people and never
get too close to a running propeller.
# If you find wrinkles on the covering as a result of weather changes, you can use hot
iron to remove the wrinkles. Please begin with lower temperature setting and
gradually raise the temperature until the wrinkles are gone. Too hot an iron may
damage the covering. Don't use hot iron near the seams or edges, hot iron will
melt the glue and shrink the covering at the same time, causing the seams to pull away.
# Check and re-tighten up all factory assembled screws, use thread locker if necessary.
0.40-0.46
more
Warning!
LINKAGE CONNECTOR
HW7111050 & HW7111060
After fastening the round nut, make sure that
the linkage connector can rotate freely.
Product Registration Form (US Customers)
We would like to share with you any relevant information regarding your model, including
product news and free upgrade parts when applicable. Please fill in the following and send to
AirBorne Models, 4749-K,Bennett Drive, Livermore, CA 94551 USA.
1. Name:
2. Address:
3. Phone #: E-mail:
4. Model:
Wing QC# Fuselage QC#
(QC numbers are stamped on wing and fuselage)
5. Date of Purchase:
6. Store Name:
Please call AirBorne Models at 925 371 0922 for any assistance in filling this form.
Thank you very much for purchasing our product.
Drill 2mm hole at servo horn.
Insert linkage connector
into servo horn.
Make sure shoulder of
screw is cleared from
servo horn.
Add washer to reduce
play if necessary.
Shoulder
Tighten up the round nut
against the shoulder. Apply
CA or permanent thread
locker.
A095PO25881103

The World Models
Manufacturing Co., LTD.
www.thew orldmod els.com
A095PO25881103