AETEK XE22-110-TX User manual

1. Use CAT5e or CAT6 UTP/STP cables and RG6 coaxial cables.
2. Please avoid using low quality cables, which will seriously limit the cabling distance and power delivery.
3. Make sure the ventilation openings on the EPoC Adapter are not blocked.
XE22-110-TX / XE22-120-TX Outdoor EPoC Adapter
Model Description
XE22-110-TX Outdoor 1 port EPoC Tx Adapter, 1x BNC, 1x FE RJ45, -30ºC~60ºC
XE22-120-TX Outdoor 2 port EPoC Tx Adapter, 1x BNC, 2x FE RJ45, -30ºC~60ºC
IMPORTANT:
INTRODUCTION
CONNECTION
PACKAGE CONTENTS
Quick Installation Guide
* 1x Outdoor EPoC Adapter * 1x Quick Installation Guide
* 1x Gray Rubber for 6~8mm coaxial cable * 1x Black Rubber for 4.5~6.5mm coaxial cable
Ethernet w/PoE
Ethernet
Coax w/Power
1200m(3937ft)
XE10-110-RX
Network Switch
XE22-110-TX
XE11-110-RX
H30-044-90
1200m(3937ft)
SD-301
Surge Protector
SD-301
Surge Protector
XE22-120-TX
NOTE:
The Outdoor EPoC Adapter & SD-301 Surge Protector must be
grounded using a ground wire between the ground screw and
earth ground.
IMPORTANT:
Ground screw
* Make sure the grouning
resistance is lower than
0.5Ω.
XE22-110-TX:
XE22-120-TX:
To disconnect a LAN cable, loosen the cable
gland and pull the cable against the socket
wall towards the side of the locking tab.
NOTE:
For further protection against water ingress and high temperature , it is recommended to locate the unit where possible:
• Horizontal installation
• Shaded from sunlight & rainfall
INSTALLED LOCATION:

LEDs
LAN Green ON LAN: Data is connection
Green ash LAN: Data is being transmitted or received.
OFF No connection
PoE Green ON PoE output to PD device
OFF No PoE output to PD device
PWR Yellow ON EPoC Adapter power status
LINK Green ON Rx and Tx EPoC Adapter is connected.
DIP Switch
DIP# On Delivery PoE output to PD device
Off No PoE output to PD device
Distance/Power Chart
Length of Coaxial Cable
300m 33.32W
500m 23.9W
800m 11.81W
1000m 8.7W
1200m 8.36W
1200m ~ 2400m Data only (100Mbps)
NOTE:
1. The numberts comply using RG6 coaxial cables.
2. The length of network cable for camera connection is 1m CAT5e
cable.
3. The power delivery will vary on the quality of coaxial cable due to
resistance.
AETEK INC.
3F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.
|T:[phone]|W:www.aetektec.com|E:[email protected]
All specications are subject to change without noice.
Copyright © 2018 AETEK INC. All rights reserved.
XE22-110-TX:
XE22-120-TX:
Waterproof plug:
PoE ON/OFF Switch
IMPORTANT - please follow the procedures below carefully to ensure the best seal:
1. Fit a BNC plug to the coaxial cable
2. Thread the coaxial cable through the cap(A) & grip(B)
3. Split rubber(C), rubber have two sizes for meet 4.5~6.5m or 6~8mm coaxial cable.
4. Fit the split rubber(C) over the coaxial cable
5. Thread the coaxial cable through the body(D)
6. Fit the washer(E) to the XE22-110-TX/XE22-120-TX connector
7. Plug the BNC connector on the coaxial cable into the XE22-110-TX/XE22-120-TX
8. Hold XE22-110-TX/XE22-120-TX and then screw the body(D) onto the XE22-110-TX/XE22-120-TX connector tighten rmly
9. Push rubber(C) in the grip(B) and screw the cap tighten rmly. The coaxial cable is sealed when the rubber(C) & grip(B) bulges to
the edge of the cap(A). The BNC Male connector needs <38mm form coaxial cable.
Connector Assembly
Washer (E) Body (D) Rubber (C) Grip (B) Cap (A)
Rubber (C) Rubber (C)
Split