AETEK XE52-120-TX User manual

1. Use CAT5e or CAT6 UTP/STP cables,and coaxial. cahle
2. Please avoid using low quality cables, which will seriously limit the cabling distance and power delivery.
3. Make sure the power source is sufcient for your conguration.
XE52-120-TX / XE62-120-TX Web Smart EPoC IPTX Adapter
Model Description
XE52-120-TX EPoC IPTX Adapter, 1x EPoC BNC, 1x FE RJ45, 1 DC Jack, -20ºC~60ºC
XE62-120-TX EPoC Outdoor IPTX Adapter, 1x EPoC BNC, 1x FE RJ45, -30ºC~60ºC
IMPORTANT:
INTRODUCTION
CONNECTION
PACKAGE CONTENTS
Quick Installation Guide
* 1x Quick Installation Guide * Waterproof Connect (XE62-120-TX only)
Ethernet (Data)
Power
RG6 Coax
RG6 Coax
Application :
Cat.5e/6 PoE (Data + Power)
Coax
Network Switch
XE52-120-TX
XE62-120-TX
XE11-110-RX
H30-044-90 NDR-240-48
240W Power SupplyUPoE Swich
XE10-110-RX
DEFAULTS
IP Address DHCP client
The rst time login need key in new username and password,
please enter the new username and password, and then click the
<Apply> button.
EPoC Link
Connect to
EPoC RX
XE52-120-TX
Connect to
PoE IP Camera
Connect to
PoE IP Camera
EPoC Link
Connect to EPoT RX
Connect to
PoE IP Camera
Connect to
PoE IP Camera
XE62-120-TX
Connect 56V/65W
Power Adapter(Option)
Join Button
Join Button
INSTALLATION
P/N: A625006200G

LEDs
PoE Yellow ON PoE: Power port is connected to PD
LAN Green ash LAN: Data is being transmitted or received.
OFF No connection
PWR Yellow ON Power is supplied
LINK Green ON Rx and Tx EPoC adapter is connected.
Distance/Power Chart
NOTE:
1. The numberts comply using RG6 coaxial cables.
2. The length of network cable for camera connection is 1m CAT5e cable.
3. The power delivery will vary on the quality of coaxial cable due to
resistance.
AETEK INC.
3F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.
|T:[phone]|W:www.aetektec.com|E:[email protected]
All specications are subject to change without noice.
Copyright © 2020 AETEK INC. All rights reserved.
To disconnect a LAN cable, loosen the cable
gland and pull the cable against the socket
wall towards the side of the locking tab.
Outdoor LAN Port
IMPORTANT -
1. Fit a BNC plug to the coaxial cable
2. Thread the coaxial cable through the cap(A) & grip(B)
3. Split rubber(C), rubber have two sizes for meet 4.5~6.5mm or 6~8mm
coaxial cable.
4. Fit the split rubber(C) over the coaxial cable
5. Thread the coaxial cable through the body(D)
6. Fit the washer(E) to the XE62-120-TX connector
7. Plug the BNC connector on the coaxial cable into the XE62-120-TX
8. Hold XE62-120-TX and then screw the body(D) onto the XE62-120-TX
connector tighten rmly
9. Push rubber(C) in the grip(B) and screw the cap tighten rmly. The coaxial
cable is sealed when the rubber(C) & grip(B) bulges to the edge of the
cap(A). The BNC Male connector needs <38mm form coaxial cable.
Outdoor EPoC LINK Port Connector Assembly
Washer (E) Body (D) Rubber (C) Grip (B) Cap (A)
Rubber (C) Rubber (C)
Split
Length of Coaxial Cable
300m 34.72W
500m 25.2W
800m 13.11W
1000m 10W
1200m 9.66W
1200m ~ 2400m Data only (100Mbps)
NOTE:
The XE62-120-TX Outdoor EPoC Adapter must be
grounded using a ground wire between the ground screw
and earth ground.
IMPORTANT:
Ground screw
* Make sure the grouning
resistance is lower than
0.5Ω.
XE62-120-TX
Reset to default 15 seconds
Mode/Reset Button
Join Button
• Press the Join button for 1-3 seconds on both Local and Remote Extenders to Link them.
• Press the Join button on the Remote Extender for 5-8 seconds to disconnect the Link between the Extenders
• Press the Join button for 10~15 seconds to reset the Extender to default.