AFL Hyperscale 10011505 User manual

Level 4 Distribution Cabinet
Installation Guide
POC
VIRGIN MEDIA APPROVED
INSTALLATION METHOD
SKU: 10011505

2
Network Topology
2f Blown
Element
12f Blown
Element
144f
Trunk Cable
Trunk
Cable
Headend/Hub (L1/L2)
VM Hub (L2.5)
Passive Distribution Node (L4) Passive Distribution Node (L4)
Passive Aggregation Node (L3)
The PoC L4 distribution cabinet
provides a splicing, splitter and
patching point for the nal
drop to the home

PoC Level 4 Distribution Cabinet Installation Guide
3
Network Distribution
Cable Tie Point
Backboard
Cable Manager
Customer
Drop Patch
Panel
Patching
Chassis
Customer Drop
Duct Tie Point
Cable / Tube
Manifold
Modular Raceway
24f Splice Tray
Splitter Tray
Item Quantity
Backboard 1
Cable Managers 8
Bend Radius Manager 1
Network Distribution Cable Tie Point 1
24f Splice Tray 6
Splitter Tray 6
Modular Raceway 4
Cable/Tube Manifold 1
8 Way Customer Drop Duct Tie Point 6
Customer Drop Patch Module 6
Patching Chassis 1
Component Overview

4
Slot studs into back panel - No tools required. Backboard must be central, top, loction as shown
1
Rear Section View
Installation Process Mount Backboard
Into Cabinet

PoC Level 4 Distribution Cabinet Installation Guide
5
Always install ducts from rear to front
Cut ducks to lenght, clip into position
(use a cable tie to straighten out duct
as required)
2Push on blowing indicator (not supplied) 3
Network Distribution Cable Customer Drop Cables
20mm Approx
20mm Approx
Micro Duct Installation

6
Tighten Gas Block
6
Install 12f cable - minimum overlength 3m from gas block
4
Network Cable Preparation and Dressing
Feed Cable Through Guide
5

PoC Level 4 Distribution Cabinet Installation Guide
7
Tie off micro duct
7Mark strip point at start of raceway
8
Strip the jacket in accordance with the cables manufacturers guidelines
9
Strip Point

8
Route 250μm bers through raceway, dress ber into tray (as per map)
NO TRANSPORT TUBING REQUIRED
10
Incoming Cable Route
No Transport
Tubing Required

PoC Level 4 Distribution Cabinet Installation Guide
9
Cassette
8
Cassette
7
Cassette
6
Cassette
5
Cassette
4
Cassette
3
CABLE #1
Pink/Rose
Aqua
Black
White
Violet
Red
Yellow
Grey
Brown
Green
Orange
Blue
Cable / Cassette Fiber Map
Splitter Input
(900μm)
Network Fiber
(250μm)
Splitter Outputs
(900μm)
Splice Protector
* Virgin Media recommended ber routing.
PLEASE CHECK SPLICING SCHEDULE!
Splice the network cable to the splitter input
11 Make sure the tray lid is tted after splicing
12

10
Straight Splice L4-L4 Pass Through (Point To
Point Between L3 and Last L4)
Incoming Cable
Incoming Cable
Outgoing Fiber
(250μm) Incoming Fiber
(250μm)
Outgoing Cable
Outgoing Cable
Strip Cable Jacket / Subunit within this area
Splice Incoming Fiber to Outgoing Fiber
Splice Protector

PoC Level 4 Distribution Cabinet Installation Guide
11
ORDERING INFORMATION
Splitter Prohibited
Port Label
SKU: 10011758
Remover dust caps
1
Component Overwiew
Complete
3
Only use on
non-live ports.
Check MDR
patching
schedule to
identify which
ports need to
be covered
over.
Replace dust caps through label
2

12
Specications
Type 1xN 1x4
Operating Wavelength range (nm) 1260~1650nm
Insertion loss (dB) Max 7.6 (with connectors)
PDL (dB) Max 0.2
Uniformity (dB) Max 0.6
PLC Return loss (dB) Min 55
Directivity (dB) Min 55
Operating Temperature (°C)
-40~+85
Storage Temperature (°C)
Houseing Dimension (mm) LxWxH 60x7x4
Fibre Type G.657A2

PoC Level 4 Distribution Cabinet Installation Guide
13
Notes

14
Notes

PoC Level 4 Distribution Cabinet Installation Guide
15
Notes

Specications are subject to change without notice.
AFLHSVMPOCL4081119V1
Installation Guide
www.aflhyperscale.com
Thank you for choosing AFL Hyperscale