AG Neovo TX-1502 User manual

TX-1502, TX-1702, TX-1902 & TX-2202 Touch Screen Monitor
User Manual
www.agneovo.com

TABLE OF CONTENTS
2
SAFETY INFORMATION
WEEE...........................................................................................................................................................4
PRECAUTIONS
Notice ...........................................................................................................................................................5
Cautions When Setting Up ........................................................................................................................... 5
Cautions When Using...................................................................................................................................6
Cleaning and Maintenance........................................................................................................................... 7
Notice for the LCD Monitor........................................................................................................................... 7
CHAPTER 1: PRODUCT DESCRIPTION
1.1 Package Contents ..................................................................................................................................8
1.2 Removing/Attaching Cable Cover .......................................................................................................... 9
1.3 Installing the Stand...............................................................................................................................10
1.4 Adjusting the Tilt ...................................................................................................................................10
1.5 Wall Mounting....................................................................................................................................... 11
1.6 LCD Monitor Overview ......................................................................................................................... 12
1.6.1 Front View .................................................................................................................................12
1.6.2 Rear View..................................................................................................................................12
1.6.3 Control Buttons..........................................................................................................................13
CHAPTER 2: MAKING CONNECTIONS
2.1 Connecting the AC Power .................................................................................................................... 16
2.2 Connecting Input Source Signals ......................................................................................................... 17
2.3 Connecting the Wired OSD Controller ................................................................................................. 17
2.4 Connecting USB for Touch Screen Control .......................................................................................... 18
Touch Disable Function.................................................................................................................. 18
2.5 Ventilation Requirements for Enclosure Locating................................................................................. 19
CHAPTER 3: USING THE LCD MONITOR
3.1 Turning on the Power ........................................................................................................................... 20
3.2 Displaying the OSD Menu .................................................................................................................... 21
3.3 Adjusting Monitor Brightness................................................................................................................ 22
3.4 Adjusting Monitor Contrast ................................................................................................................... 23
CHAPTER 4: ON SCREEN DISPLAY MENU
4.1 Using the OSD Menu ........................................................................................................................... 24
4.2 OSD Menu Tree ...................................................................................................................................26
CHAPTER 5: ADJUSTING THE LCD MONITOR
5.1 Picture Menu ........................................................................................................................................27
5.2 Colour Menu.........................................................................................................................................29
5.3 OSD Menu............................................................................................................................................30
5.4 System Menu .......................................................................................................................................31
CHAPTER 6: APPENDIX
6.1 Warning Messages...............................................................................................................................32
6.2 Timing...................................................................................................................................................33
6.3 Touch Screen Driver Installation........................................................................................................... 35

3
TABLE OF CONTENTS
6.3.1 Optional Calibration Tool Install................................................................................................. 35
6.3.2 Driver Installation Instructions ...................................................................................................36
6.4 Cleaning ...............................................................................................................................................37
6.5 Troubleshooting....................................................................................................................................38
6.6 Transporting the LCD Monitor .............................................................................................................. 39
CHAPTER 7: SPECIFICATIONS
7.1 Monitor Specications .......................................................................................................................... 43
7.2 Monitor Dimensions.............................................................................................................................. 44

SAFETY INFORMATION
4
WEEE
Information for users applicable in European Union countries.
The symbol on the product or its packaging signies that this product has to be
disposed separately from ordinary household wastes at its end of life. Please kindly
be aware that this is your responsibility to dispose electronic equipment at recycling
centers so as to help conserve natural resources. Each country in the European Union
should have its collection centers for electrical and electronic equipment recycling.
For information about your recycling drop off area, please contact your local related
electrical and electronic equipment waste management authority or the retailer where
you bought the product.
SAFETY INFORMATION

5
PRECAUTIONS
PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Symbols used in this manual
This icon indicates the existence of a potential hazard that could result in personal injury
or damage to the product.
This icon indicates important operating and servicing information.
Notice
• Read this User Manual carefully before using the LCD monitor and keep it for future reference.
• The product specications and other information provided in this User Manual are for reference only. All
information is subject to change without notice. Updated content can be downloaded from our web site at
www.agneovo.com.
• To protect your rights as a consumer, do not remove any stickers from the LCD monitor. Doing so may
affect the determination of the warranty period.
Cautions When Setting Up
Do not place the LCD monitor near heat sources, such as a heater, exhaust vent, or in direct
sunlight.
Do not cover or block the ventilation holes in the housing.
Place the LCD monitor on a stable area. Do not place the LCD monitor where it may subject to
vibration or shock.
Place the LCD monitor in a well-ventilated area.
Do not place the LCD monitor outdoors.
Do not place the LCD monitor in a dusty or humid environment.
Do not spill liquid or insert sharp objects into the LCD monitor through the ventilation holes.
Doing so may cause accidental re, electric shock or damage the LCD monitor.
Precautions

6
PRECAUTIONS
Cautions When Using
Use only the power cord supplied with the LCD monitor.
The power outlet should be installed near the LCD monitor and be easily accessible.
If an extension cord is used with the LCD monitor, ensure that the total current consumption
plugged into the power outlet does not exceed the ampere rating.
Do not allow anything to rest on the power cord. Do not place the LCD monitor where the
power cord may be stepped on.
If the LCD monitor will not be used for an indenite period of time, unplug the power cord from
the power outlet.
To disconnect the power cord, grasp and pull by the plug head. Do not tug on the cord; doing
so may cause re or electric shock.
Do not unplug or touch the power cord with wet hands.
WARNING:
Unplug the power cord from the power outlet and refer to qualied service personnel under
the following conditions:
• When the power cord is damaged.
• If the LCD monitor has been dropped or the housing has been damaged.
• If the LCD monitor emits smoke or a distinct odor.
Ceiling mount or mount on any other horizontal surface overhead are not advisable.
WARNING:
Installation in contravention of the instructions may result in undesirable consequences,
particularly hurting people and damaging property. Users who have already mounted the
monitor on the ceiling or any other horizontal surface overhead are strongly advised to
contact AG Neovo for consultations and solutions to help ensure a most pleasurable and
fullling monitor experience.

7
PRECAUTIONS
Cleaning and Maintenance
Do not attempt to service the LCD monitor yourself, refer to qualied service personnel.
Opening or removing the covers may expose you to dangerous voltage or other risks.
Notice for the LCD Monitor
In order to maintain the stable luminous performance, it is recommended to use low brightness setting.
Due to the lifespan of the lamp, it is normal that the brightness quality of the LCD monitor may decrease
with time.
When static images are displayed for long periods of time, the image may cause an imprint on the LCD
monitor. This is called image retention or burn-in.
To prevent image retention, do any of the following:
• Set the LCD monitor to turn off after a few minutes of being idle.
• Use a screen saver that has moving graphics or a blank white image.
• Switch desktop backgrounds regularly.
• Adjust the LCD monitor to low brightness settings.
• Turn off the LCD monitor when the system is not in use.
Things to do when the LCD monitor shows image retention:
• Turn off the LCD monitor for extended periods of time. It can be several hours or several days.
• Use a screen saver and run it for extended periods of time.
• Use a black and white image and run it for extended periods of time.
There are millions of micro transistors inside the LCD monitor. It is normal for a few transistors to be
damaged and to produce spots. This is acceptable and is not considered a failure.

CHAPTER 1: PRODUCT DESCRIPTION
8
1.1 Package Contents
When unpacking, check if the following items are included in the package. If any of them is missing or
damaged, contact your dealer.
Chapter 1: Product Description
LCD Monitor
Quick Start Guide
Power Adaptor(*)
Warranty Card
Power Cord
USB CableVGA Cable
TX-1502/1702/1902 TX-2202
TX-1502/1702/1902/2202_Quick Guide_V010
Quick Start Guide
TX-1502, TX-1702, TX-1902 & TX-2202 LCD Monitor
www.agneovo.com
Note:(*)
• Use only the supplied power cord.
• The above pictures are for reference only. Actual items may vary upon shipment.
• (*) Must use only the supplied power adapter:
- Vendor: Delta
- Model no.: ADP-50YH B
- Rating: DC 12V, 4.16A
HDMI Cable
Cable Cover and Screw
(M3 x 6)

9
PRODUCT DESCRIPTION
1.2 Removing/Attaching Cable Cover
1. Lay the LCD monitor face down on a at even surface.
2. Press on the cable cover latches and then remove the cable cover as shown in the
illustration below.
Cable Cover
3. After connect the cables to the appropriate connectors and position all cables under the
cover lip, attach the cable cover. Take the screw (M3 x 6) from the accessory box, and insert
the screw into the cable cover and monitor

10
PRODUCT DESCRIPTION
1.3 Installing the Stand
1. Lay the LCD monitor face down on a at even surface.
2. By aligning with the screw holes, install the stand to the rear of the LCD monitor.
3. Attach the stand to the monitor with the screws.
1.4 Adjusting the Tilt
For comfort viewing, tilt the LCD monitor up to an angle of -5° to 90°. Hold the stand with one hand and use
the other to adjust the LCD monitor to the desired angle.
90°
-5°

11
PRODUCT DESCRIPTION
1.5 Wall Mounting
To wall-mount the LCD monitor, screw the mounting bracket to the VESA holes at the rear of the LCD monitor.
MENU
SELECT
100 mm
100
mm
MENU
SELECT
100 mm
100 mm
TX-1502/1702/1902 TX-2202
Note: Take measures to prevent the LCD monitor from falling down and lessen possible injury and damage
to the monitor in case of earthquakes or other disasters.
• Use only the 100 x 100 mm wall mount kit recommended by AG Neovo. All
AG Neovo wall mount kits comply with VESA standard.
• Secure the LCD monitor on a solid wall strong enough to bear its weight.
• It is suggested to wall mount the LCD monitor without tilting it facing
downward.
• For TX-1502/1702/1902, the distance between the back cover surface and
the bottom of the screw hole is 8 mm. Please use four M4 screws diameter
with proper length to mount your monitor. The mounting stand must be able
to support at least 10.1 lb (4.6 kg) (TX-1502), 12.8 lb (5.8 kg) (TX-1702), or
14.3 lb (6.5 kg) (TX-1902).
• For TX-2202, the distance between the back cover surface and the bottom
of the screw hole is 7 mm. Please use four M4 screws diameter with proper
length to mount your monitor. The mounting stand must be able to support
at least 6.1 kg (13.5 lb).

12
PRODUCT DESCRIPTION
1.6 LCD Monitor Overview
1.6.1 Front View
TX-1502/1702/1902 TX-2202
1.6.2 Rear View
MENU
SELECT
MENU
SELECT
DC IN DisplayPort HDMI VGA RJ11 USB
1 2 3 4 5 6
TX-1502/1702/1902 TX-2202
1DC IN:
Connect with the supplied power adaptor.
2DisplayPort:
Connect DisplayPort signals input.
3HDMI:
Connect HDMI signals input.
4VGA:
Connect VGA signals input.

13
PRODUCT DESCRIPTION
5RJ11:
Connect with wired OSD control. (Don’t connect telephone or internet cable to RJ-Type port.)
6USB:
Connect USB for touch screen control.
1.6.3 Control Buttons
MENU
SELECT
MENU
SELECT
MENU
SELECT
1
2
3
4
5
6
TX-1502/1702/1902 TX-2202
1MENU:
• OSD menu ON/OFF and return to main item.
2UP (p): Hot Key: Brightness
• When OSD menu is ON, navigate through adjustment icons or adjust a function.
• When the UP key is pressed, the brightness can be adjusted. The UP/DOWN key can be used
for brightness adjustment.
Brightness
Press<▲,▼> to Adjust and <Menu> to Exit
50

14
PRODUCT DESCRIPTION
3DOWN (q): Hot Key: Contrast
• When OSD menu is ON, navigate through adjustment icons or adjust a function.
• When the DOWN key is pressed, the contrast can be adjusted. The UP/DOWN key can be used
for contrast adjustment.
Contrast
Press<▲,▼> to Adjust and <Menu> to Exit
50
4SELECT:
• When OSD menu is ON, the key is used for function adjustment conrmation.
• When selecting the input source:
- If the monitor is in ON mode, press the SELECT key for 3 seconds to turn on the “Source
Select” menu.
- If the monitor is in Standby mode, press the SELECT key for 1 second to turn on the “Source
Select” menu.
Note: For detailed adjustment of “Source Select”, please refer to page 31.
5POWER ( ):
• Press to turn the monitor ON or OFF.
6Power Indicator (for TX-2202 only):
Indicate the operating status of the LCD monitor:
• Lights Green when the LCD monitor is turned on.
• Lights Amber when the LCD monitor is in standby mode.
• Lights Off when the LCD monitor is turned off.

15
PRODUCT DESCRIPTION
Note: To lock/unlock the MENU key and/or the key, press the MENU and qkeys simultaneously. Then
select the desired lock/unlock function.
Press<▲,▼> to Adjust and <Menu> to Exit
Lock
OSD Key Inactive
Power Key Inactive
Press<▲,▼> to Adjust and <Menu> to Exit
Lock
No Yes

CHAPTER 2: MAKING CONNECTIONS
16
CAUTION:
Make sure that the LCD monitor is not connected to the power outlet before making any
connections. Connecting cables while the power is ON may cause possible electric shock or
personal injury.
2.1 Connecting the AC Power
1. Connect the power cord to the power adapter.
2. Connect the power adapter to the DC power input at the rear of the LCD monitor.
3. Connect the power cord plug to a power outlet or a power supply.
DC IN
AC IN
CAUTION:
When unplugging the power cord, hold the power cord by the plug head. Never pull by the cord.
Chapter 2: Making Connections

17
MAKING CONNECTIONS
2.2 Connecting Input Source Signals
Input source signals can be connected with either of the following cables:
DisplayPort HDMI VGA
DisplayPort HDMI VGA
• DisplayPort
Connect one end of a DP cable to the DisplayPort
connector of the LCD monitor and the other end to the
DisplayPort connector of the computer.
• HDMI
Connect one end of an HDMI cable to the HDMI connector
of the LCD monitor and the other end to the HDMI
connector of the computer.
• VGA
Connect one end of a D-Sub (VGA) cable to the D-Sub
(VGA) connector of the LCD monitor and the other end to
the D-Sub (VGA) connector of the computer.
Note: To ensure the LCD monitor works well with your
computer, please congure the display mode of
your graphics card to make it less than or equal to
1024 x 768 (for TX-1502), 1280 x 1024 (for TX-
1702 & TX-1902), or 1920 x 1080 (for TX-2202)
resolution and make sure the timing of the display
mode is compatible with the LCD monitor. For
compatible Video Modes of your LCD monitor,
please refer to “6.2 Timing” on page 33.
2.3 Connecting the Wired OSD Controller
Connect the wired OSD controller (optional, not supplied) to the RJ11 connector of the LCD monitor.
RJ11
MENU
SELECT
MENU
SELECT

18
MAKING CONNECTIONS
2.4 Connecting USB for Touch Screen Control
Connect one end of a USB cable to the USB connector of the LCD monitor and the other end to the USB
connector of the computer.
USB
USB
MENU
SELECT
Touch Disable Function
To disable the touch function, do the following:
1. Press “Menu” and “Select” keys simultaneously. The “Touch disable” message appears on
the screen.
Touch disable
2. To enable the touch function, press “Menu” and “Select” keys simultaneously for ve
seconds.

19
MAKING CONNECTIONS
2.5 Ventilation Requirements for Enclosure Locating
To allow heat to disperse, avoid installing the LCD monitor directly on the cabinet wall and make sure the
operating/storage temperature/humidity requirements are met as described below:
• Operating conditions: 0°C-40°C (32°F-104°F)
• Operating humidity (non-condensing): 20%-80%
• Operating altitude: < 10,000 feet (3,048m)
• Storage conditions: -20°C-60°C (-4°F-140°F)
• Storage humidity (non-condensing): 10%-90%

CHAPTER 3: USING THE LCD MONITOR
20
3.1 Turning on the Power
1. Connect the power to the LCD monitor. Refer to page 16.
2. Press the key on the control panel to turn the LCD monitor on.
MENU
SELECT
MENU
SELECT
Power Key
When the LCD monitor is turned on, press the key on the control panel three times to turn off the LCD
monitor.
Do you want to turn off?
Please press the power button again.
Note: The LCD monitor still consumes power as long as the power cord is connected to the power outlet.
Disconnect the power cord to completely cut off power.
Chapter 3: Using the LCD Monitor