AGMel A910 User manual

No display
dim display
Dead battery.
Instrument failure.
Unstable
measurement
Dead battery.
Cable to test not faulted.
Measurement carried out
immediately after a voltage
test.
Cable to test too short.
Cable to test not connected.
Broken test leads.
Instrument failure.
AGMel
IA910 Rev 2 04/13
2002/95/EC
EXAMPLE
Faulted cable is 5000 meters long.
The value read in position ”E”, LE, is
4.7%, the value LB is 4.7 %.
the cable has only one contact at
distance:
4.7 x 5000 = 6175
100
meters from the Outside end of the
cable.
SPECIFICATIONS
Can test cables with a loop resistance
≥ 5mΩ (≈ 90 m @ 300 mm ) and
≤ 30 kΩ.
Range: > 100 km @ 300 Ω/km
Basic accuracy: ± 0.1 % ± 1 digit
Maximum measuring current: 1A
Maximum applied voltage: 70 mV
Power supply: 7.2 ÷ 9V , 6 x AA size
Alkali e or NiCd/NiMh batteries
Battery life: 1000 measur. @ 100 mΩ
Weight: 5 0 g
Dimensions: 110 x 204 x 41 mm
USER MANUAL
Short circuit locator
for metallic cables
Mod. A910
SERVICING INFORMATION
If you have questions or need further
assistance, please email us at
[email protected]
Our complete catalog can be viewed,
printed or book marked from our
website: www.agminstruments.com
AGM Elettronica
Via Marziale, 9
80067 Sorrento (NA)
Italy
Tel [phone]
Fax[phone]
www.agminstruments.com
E-mail: [email protected]
TRO BLESHOOTING
CALIBRATION
Our instruments are calibrated using
the following standards
Datron 4705 Autocal Multifunction Calibrator
Yokogawa 7563 Precision Digital Ther o eter
GenRad 1686 Digital Capacitance Meter
Agilent 66309D Mobile Co unic. Source
HP 34401 Multi eter
HP 34970A Data Acquisition Unit
Burster 1424 IEEE488 High Precision Decade
Tettex 3200/BU Standard Resistor
AOIP 0,01 Standard ResistorΩ
Tettex Decade Capacitors
ARCO Standard Capacitors
JBC 5001 Standard Capacitor
Lecroy LT264ML Oscilloscope
Haefely PU12 I pulse tester
Schaffner NSG431 Electr. Discharge Si ulator
Lecroy 9109 Arbitrary Function Generator
Norbar 40051 Torque eter
HP 3577A Network Analyzer

1 probes connector 4 battery holder
2display 5 measure mode select
3 measure switch
DESCRIPTION
The A910 is a short circuit locator for
electric, telephone and power cables
wind on the reel; it gives the position
of the fault from the inside or outside
end of the cable, in percentage to the
total cable length.
HOW TO SE IT
Ground the cable to be tested from
any electrical charges.
If wire “A” is short with “B”, connect
the crocodile clips to the cable:
1) the crocodile clip “I” to “A”
from the inside end.
2 the crocodile clip “E” to “A”
from the outside end.
3) the crocodile clip “COM” to
“B” from the outside end.
Perform a calibration test:
turn the measure mode knob to “Ref”
and push the measure switch, the
display will show 100.0 ± 0.1 %,
otherwise: :
a) the cable has a total
resistance below 5 mΩ
Connect wire with lead
A
B COM
B COM
A I
Lead connections
b) the cable has some
electrostatic charges within
c) the test leads are broken.
Turn the measure mode knob to “E”
and push the measure switch, read on
the display the value LE, length of the
cable (in percentage to the total cable
length) from clip “E” to the short.
Switch the crocodile clip “COM”
to wire “B” from the inside end
push the measure switch, read on the
display the value LB; if LE = LB ± 0.1
%, than the cable has just one short at
distance:
(Value LE) x (total length of cable)
100
from the outside end of the cable.
If LE ≠ LB ± 0.1 %, the cable has
more than one short and the distance
to fault is calculated making use of the
program supplied with the instrument.
To measure the distance to fault from
the inside end of the cable, turn the
measure mode knob in position “I”
and push the measure switch.
To remove the battery door push the two
gray plastic tabs.
Be careful to observe battery
polarity during installation !
WARNINGS AND SAFETY R LES
The locator is protected against
electrical charges, but in some
conditions these charges on the wire
can accumulate and can be
dangerous for the technician,
therefore
always ground the cable
before any measurement
Do not short the clips “I” with “E” for a
long time, otherwise the battery life
will be reduced.
The calibration test is possible only
after a cable is connected.
The crocodile clips “I” and “E” are
special Kelvin clips, do not force the
opening.
1
2
3
4
5