Agri-Fab 45-03084 User manual

OWNER'S
MANUAL
MODEL NO.
45-03084
UNivERSAL TOW BEhiND TiLLER
• Assembly
• Operation
• Customer Responsibilities
• Service and Adjustment
• Repair Parts
FORM NO. 40566 (05/09/08)
CAUTION:
Read Rules for
Safe Operation
and Instructions
Carefully
Printed in U.S.A.
™
the fastest way to purchase parts
www.speedepart.com

2
SAFETY RULES.......................................................... 3
ASSEMBLY...............................................................4-5
OPERATION.............................................................6-8
MAINTENANCE .....................................................9-10
SERVICE AND ADJUSTMENT ............................11-12
STORAGE ................................................................. 12
TROUBLESHOOTING...............................................13
REPAIR PARTS ....................................................14-16
PARTS ORDERING/SERVICE ....................Rear Cover
TABLE OF CONTENTS
This unit is equipped with an internal combustion engine
and should not be used on or near any unimproved forest
covered, brush covered, or grass covered land unless
the engine's exhaust system is equipped with a spark
arrester meeting applicable local or state laws (if any). If a
spark arrester is used, it should be maintained in effective
working order by the operator.
In the state of California the above is required by law
(Section 4442 of the California Public Resources Code).
Other states may have similar laws. Federal laws apply on
federal lands. A spark arrester mufer is available at your
nearest authorized engine service center.

3

4
TO REMOvE UNiT FROM
CARTON
• Cut from top to bottom all four corners of the carton
and lay panels at. (See Fig. 1)
• Remove the lag screw that holds the oating hitch to
the packing skid.
• Disassemble and discard carton's wood top and side
supports.
• Remove four hex bolt, hex nuts and at washer from
the hold down brackets at the rear of the carton.
• Remove and save the two Flat Washers and Cotter
Pins from the rear axle. Reuse when attaching gauge
wheels.
• Discard all other packing hardware and hold down
brackets.
ASSEMBLY
TO iNSTALL ThE TiLLER
GAUGE WhEELS
• Assemble Gauge Wheels onto the Rear Axle with the
extended end of Hub facing inward. Secure with the
Flat Washers and Cotter Pins which you removed from
the axle during unpacking. (See g. 2.)
• Right hand (RH) and left hand (LH) are determined
from the drivers position while seated on the tractor.
• We recommend that you remove the Mower Deck
before using the Tiller. Refer to your Tractor Owner's
Manual.
3/8" NYLOCK
NUT
TO iNSTALL ThE TiLLER TiNE
ASSEMBLiES
• Attach the oating hitch to the tractor's draw bar.
(Refer to Operating Instructions on page 7.)
• Remove the preassembled 3/8" x 2" hex bolt and 3/8"
nylock nut from the L.H. Tine Assembly. Slide the tine
assembly onto the Transmission Axle on the left side
of the tiller and secure with the hex bolt and nylock nut.
(See g. 3.) Repeat for the R.H. side.
FiG. 1
FiG. 2
FiG. 3

5
FiG. 4
TO iNSTALL (WhEEL)
WEiGhTS TO TiLLER
NOTE: Weights are not furnished with the Tiller. 30 lb.
tractor wheel weights may be purchased to mount to the
Tiller if extra weight is required. (Refer to the Operation
section of this manual.)
• Remove two Carriage Bolts and Nuts from each Tine
Shield, located approximately 3-1/2" from the front
edge. See g. 4.
• Place (Wheel) Weights on Tine Shield and secure with
long Bolts and Nuts furnished with the Weights. See
g. 4.
ASSEMBLY