aguri Skyway User manual

1
www.aguriworld.co.uk
User Manual
SKYWAY | Drive Assist

2 3
What’s in the box? 3
Product overview 4
Standby screen explained 5
Installing your Skyway
on the windscreen 5
Installing your Skyway using
the sticky pad dash mount 6
Connecting to power 6
Installation tips 7
General operation 7
Menu settings 8
Speed trap alert settings 8
Radar/laser alert settings 8
GPS Speed trap alert settings 8
Brightness control 10
On/Off/Volume control 10
Smart, City and Highway
modes 10
Choose between Radar + GPS
alerts, GPS alerts only or
Radar alerts only 11
Vehicle low battery warning 12
Factory reset 12
Control Radar/laser alerts
by speed 12
Geo Radar alerts 12
Directional alerts 13
User POI. Add you own
user point alerts 13
How to delete your
user point alerts 14
Set audible alerts 14
Automute time 15
Automute volume 15
Highway Smart Mute 15
City Smart Mute 16
Smart Mute GPS speed
trap alerts 16
Select preferred speed unit 17
Overspeed alert 17
GMT time zone setting 17
GPS speed calibration 18
Current location 18
GPS and Radar/Laser
speed trap alert
screens explained 19
How to update your
Skyway GTX90 using a PC 22
Warranty 27
Contents

3
What’s in the box?
1 x Aguri Skyway GTX90
1 x 12V cigarette lighter power cable
1 x 12V hard-wire lead
1 x Sticky pad dash mount
1 x Windscreen bracket
1 x USB data cable
1 x User guide
Please note that you must power your Skyway with the 12V
cigarette lighter cable or the 12V hard-wire lead provided.
Your Skyway will not work correctly if you attempt to power
it via a 5V USB cable or the USB data socket.

4 5
Product overview
1. DC Power in.
2. On/Off/Volume control.
3. Radar receiver.
4. Press to release windscreen
bracket.
5. Loudspeaker.
6. 360 degree laser receiver.
7. USB port for updating only.
Please note you cannot power
the unit by USB as it will not
work correctly.
8. OLED display.
9. Long press Menu button to
enter and exit settings menu.
Short press Menu button to
adjust brightness in standby
mode.
10. Short press to temporarily
mute audible alerts and use to
scroll left or down when in
settings menu. Long press
to save your own user point
alerts.
11. Short Press to switch between
city and highway modes and
use to scroll right or up when in
settings menu.
Please note that you must power your Skyway with the 12V
cigarette lighter cable or the 12V hard-wire lead provided. Your
Skyway will not work correctly if you attempt to power it via a
5V USB cable or the USB data socket on the side of the unit.
1
2
3
4
67
59
11
10
8

5
Standby screen explained
Installing your Skyway on the windscreen
Attach the windscreen bracket by sliding it into the slot on the rear of
the unit. (Attach the suction cups if they are not already attached) Using
the suction cup bracket, mount your Skyway in a safe and convenient
position in the front windscreen where it has an unobstructed view of
the road ahead. We recommend mounting it toward the bottom of the
windscreen, just above the dashboard so that it has a good view of the
road ahead, but so that its view is not obstructed by the windscreen
wipers. Remember, that you will need to attach the power cable to
the unit and plug the other end in to your cigarette lighter/12V power
socket, so nd a position where this can be done without obstructing or
becoming a danger to the driver or passengers.
Once you have chosen a suitable location, thoroughly clean the glass,
then press the suction cup bracket to position, ensuring that it is well
secured. Finally, adjust the bracket so that the unit is in a horizontal
position. Please note that you will have to gently bend the bracket to
do this.
Do not leave your Skyway in the windscreen when you leave your
vehicle in hot and sunny conditions.
GPS status - connected
GPS clock Your speedSmart mode

6 7
Installing your Skyway using the sticky pad dash mount
The sticky pad can be attached, removed, and reattached many times
without losing its adhesion, and should be safe to use on most surfaces
but please check before use.
Find a at location on your dashboard where you can mount your
Skyway in a safe and convenient position and where it has an
unobstructed view of the road ahead. Remember, that you will need
to attach the power cable to the unit and plug the other end in to your
cigarette lighter/12V power socket, so nd a position where this can
be done without obstructing or becoming a danger to the driver or
passengers.
The sticky pad should automatically stick wherever you put it, but this
will vary depending on the material and type of surface your dashboard
has. Only use the sticky pad if you are sure, it is not going to move
when driving.
Once you have found a suitable location for the sticky pad and have
checked that it will not move when driving, place the Skyway on to it.
The unit should not move from the pad when driving but double check
that it is secure before using.
Do not leave your Skyway or sticky pad on the dashboard when you
leave your vehicle in hot and sunny conditions.
Connecting to power
Attach the small end of the power cable to the ‘DC in’ socket on the
side of the unit. Insert the other end into an appropriate cigarette
lighter/12V socket in your vehicle.
User note. Do not attempt to power Skyway in your vehicle
using the USB cable or USB socket. A 5V USB power supply
will not provide adequate power to run Skyway and it will not
operate correctly. The USB socket and data cable is to be
used for updating the software and speed trap database only.

7
General operation
We have shipped your Skyway with the user settings, set for optimum
performance in the UK as follows:-
Radar/laser alert settings
GPS alert settings
PAGE 5 PIC
Installation tips
Before mounting your Skyway, clean the area of the windscreen
where you have chosen to mount your unit, with a good quality
glass cleaner to ensure the suction cup bracket makes a good
contact.
Remember to mount the unit and install the power cable safely in
a location where it does not interfere with the driver or the controls
of the vehicle.
It is also possible to ‘hard-wire’ your Skyway and hide the power
cables, providing a neater installation. Please contact an auto
electrician or your local car dealer for further details.

8 9
Menu settings
Speed trap alert settings
It is possible to switch individual radar frequencies and speed traps on
and off, to ne tune Skyway to the country you are driving in.
Enter the settings menu by pressing and holding the ‘Menu’ button.
Scroll left or right, using the ‘Mute’ or ‘City’ buttons, until you highlight
the radar frequency or speed trap alert you want to change and press
the ‘Menu’ button to select it. Use the ‘Mute’ or ‘City’ buttons to switch
the feature on or off and press the ‘Menu’ button to conrm your
selection. The following options are available:-
Radar/laser alert settings
K Band - On/Off
Gatos RT3 - On/Off
Gatos RT4 - On/Off
Multa (Multa-radar)
- On/Off
Ka Band - On/Off
Laser - On/Off
GPS alert settings
Speed trap alerts
- On/Off
Red light cameras
- On/Off
Mobile speed trap
locations - On/Off

9
Using Skyway in other countries outside of the UK.
Below are the speed trap alert settings we would recommend for a
selection of other countries if you want to use your Skyway outside of
the UK.
Warning. Please note that it is illegal to use a GPS/radar/laser detector
in France. We do not recommend you use Skyway if driving in France.
Please note that it may be illegal to use a radar/laser detector in Spain,
so please check local laws before using Skyway in Spain.
Warning. Whilst we have provided some advice on the use of GPS/
radar/laser detectors above, the laws surrounding the use and owner-
ship of GPS speed trap detectors and radar/laser speed trap detectors,
varies from country to country. It is the sole responsibility of the driver
to check the local laws of the country they are driving in or intend to
drive in, before using Skyway or any other form of GPS speed trap
detector or radar/laser speed trap detector.
Germany/Austria
Radar/laser
alert settings
• K Band – On
• Gatos RT3 – On
• Gatso RT4 – On
• Multa
(Multa-radar) – On
• Ka Band – On
• Laser – On
GPS alert settings
• Speed trap alerts – On
• Red light cameras – On
• Mobile speed trap
locations – On
Spain/Portugal
Radar/laser
alert settings
• K Band – On
• Gatos RT3 – On
• Gatso RT4 – On
• Multa
(Multa-radar) – On
• Ka Band – On
• Laser – On
GPS alert settings
• Speed trap alerts – On
• Red light cameras – On
• Mobile speed trap
locations – On
Italy
Radar/laser
alert settings
• X Band - Off
• K Band – On
• Gatos RT3 – On
• Gatso RT4 – On
• Multa
(Multa-radar) – On
• Ka Band – On
• Laser – On
GPS alert settings
• Speed trap alerts – On
• Red light cameras – On
• Mobile speed trap
locations – On

10 11
Brightness control
You can choose between three levels of brightness.
• 100% Brightness
• 50% Brightness
• Auto - 100% Brightness between 6:00 to 17:59 and
50% brightness between 18:00 and 05:59
• Dark – Stealth mode. Screen will remain black apart from one small
white dot to indicate the unit is powered on and working. Your
Skyway will continue to alert in this mode, but you will only receive
audible alerts and no visual alerts.
• Temporary dark – Active stealth mode. The screen will go black with
one white dot to indicated it is powered on but will automatically
come back on again during a speed trap or radar/laser alert,
providing both a visual and audible alert. Once the threat has passed,
the screen will go black again.
Short press the ‘Menu’ button in standby mode to change the
brightness of the display screen.
On/Off/Volume control
Rotate the volume control away from you to power the unit and
increase the volume.
Rotate the volume control towards you to power the unit off and
decrease the volume.
Smart, City and Highway modes
Smart, City and Highway modes are designed to reduce the amount of
false radar alerts you might experience, particularly in built-up areas of
towns and cities. There are two City modes, one Highway mode and
Smart mode to choose from. Press the City button when in standby
mode to scroll through the different options. Select Highway for maximum
radar sensitivity, City 1 for medium radar sensitivity, City 3 for low radar
sensitivity or Smart mode which automatically switches between the City
and Highway modes based on the speed you are travelling.

11
Highway mode
City 1
City 2
Smart mode (recommended)
If Smart mode is selected, your Skyway will start in City 2 up to
20mph, then switch to City 1 between 20mph and 30mph and will
then automatically switch to Highway mode when you exceed 30mph.
Please note that the Smart mode icon will continue to be displayed
regardless of the operation mode running.
User note. Laser is always set to maximum sensitivity
regardless of the mode selected.
Choose between Radar + GPS alerts, GPS alerts only
or Radar alerts only
Press and hold the City button when in standby mode to switch between
the 3 options.

12 13
Vehicle low battery warning
Your Skyway GTX90 will automatically alert you if your vehicles battery
drops below 10.5V and needs recharging.
Factory reset
Press and hold the Menu, Mute and City buttons simultaneously until
the OLED displays ‘Factory reset’. Performing a factory reset will return
the unit to it’s original factory settings.
Control Radar/laser alerts by speed
Use this setting to block radar/laser alerts when travelling
below a set speed.
Enter the settings menu by pressing and holding the ‘Menu’ button.
Scroll left or right, using the ‘Mute’ or ‘City’ buttons, until you highlight
the icon feature above and press the ‘Menu’ button to select it. Use the
‘Mute’ or ‘City’ buttons to set the speed value you require and press
the ‘Menu’ button to conrm your selection and return to the menu.
Press and hold the menu button to return to the standby screen or
wait a few seconds and your Skyway will return to the standby screen
automatically.
Geo Radar alerts
Switch this feature on to restrict all radar alerts to
within 350m of a GPS speed trap alert to help reduce
false radar alerts.
Enter the settings menu by pressing and holding the ‘Menu’ button.
Scroll left or right, using the ‘Mute’ or ‘City’ buttons, until you highlight
the feature graphic above and press the ‘Menu’ button to select it.
Use the ‘Mute’ or ‘City’ buttons to turn the setting on or off and press
the ‘Menu’ button to conrm your selection and return to the menu.
Press and hold the menu button to return to the standby screen or
wait a few seconds and your Skyway will return to the standby screen
automatically.

13
Directional alerts
Use this setting to determine whether you get alerts to
GPS speed camera traps in both directions or just the
direction of operation. Switch off to get alerts in both
direction and switch on to only get alerts in the direction of operation.
Enter the settings menu by pressing and holding the ‘Menu’ button.
Scroll left or right, using the ‘Mute’ or ‘City’ buttons, until you highlight
the feature graphic above and press the ‘Menu’ button to select it.
Use the ‘Mute’ or ‘City’ buttons to turn the setting on or off and press
the ‘Menu’ button to conrm your selection and return to the menu.
Press and hold the menu button to return to the standby screen or
wait a few seconds and your Skyway will return to the standby screen
automatically.
User POI. Add your own user point alerts
Use this feature to add and create alerts for your own
locations in your Skyways internal memory. You can
store up to 99 of your own user points.
Enter the settings menu by pressing and holding the ‘Menu’ button.
Scroll left or right, using the ‘Mute’ or ‘City’ buttons, until you highlight
the feature graphic above and press the ‘Menu’ button to select it.
Use the ‘Mute’ or ‘City’ buttons to turn the setting on or off and press
the ‘Menu’ button to conrm your selection and return to the menu.
Press and hold the menu button to return to the standby screen or
wait a few seconds and your Skyway will return to the standby screen
automatically.
Once you have switched the User POI feature on, you can add your
own locations by pressing and holding the ‘Mute’ button, whilst moving,
at any location you choose. The display will conrm that the user POI
has been saved successfully.

14 15
How to delete your user point alerts
How to delete all the user points you have saved
Enter the settings menu by pressing and holding the ‘Menu’ button.
Scroll left or right, using the ‘Mute’ or ‘City’ buttons, until you highlight
the feature graphic above and press the ‘Menu’ button to select it. Use
the ‘Mute’ or ‘City’ buttons to select ‘Yes’ followed by the ‘Menu’ button
to delete all your POI locations and return to the menu. Press and hold
the menu button to return to the standby screen or wait a few seconds
and your Skyway will return to the standby screen automatically.
How to delete a single user point you have saved
Press and hold the ‘Mute’ button whilst the unit is alerting to the User
POI you want to delete. The display will conrm that the user point has
been deleted successfully.
User note. It is also possible to manage your user points using the
Skyway GTX90 updater. Please see instructions later on in this manual.
Set audible alerts
Use this setting to choose between
the following audible alerts:-
• Voice + beeps
• Voice only
• Beeps only
Enter the settings menu by pressing and holding the ‘Menu’ button.
Scroll left or right, using the ‘Mute’ or ‘City’ buttons, until you highlight
the feature graphic above and press the ‘Menu’ button to select it. Use
the ‘Mute’ or ‘City’ buttons to select your preferred option and press the
‘Menu’ button to conrm it and return to the menu. Press and hold the
menu button to return to the standby screen or wait a few seconds and
your Skyway will return to the standby screen automatically.

15
Automute time
Select how long you want the unit to alert at full
volume before automatically reducing to your
chosen muted volume.
Enter the settings menu by pressing and holding the ‘Menu’ button.
Scroll left or right, using the ‘Mute’ or ‘City’ buttons, until you highlight
the feature graphic above and press the ‘Menu’ button to select it. Use
the ‘Mute’ or ‘City’ buttons to select your preferred value in seconds
and press the ‘Menu’ button to conrm it and return to the menu.
Press and hold the menu button to return to the standby screen or
wait a few seconds and your Skyway will return to the standby screen
automatically.
Automute volume
Select how long you want the unit to alert at full
volume before automatically reducing to your
chosen muted volume.
Enter the settings menu by pressing and holding the ‘Menu’ button.
Scroll left or right, using the ‘Mute’ or ‘City’ buttons, until you highlight
the feature graphic above and press the ‘Menu’ button to select it. Use
the ‘Mute’ or ‘City’ buttons to select the level you want the volume to
reduce to when the volume is automatically muted. For example, if
you select 30%, the volume will be reduced by 70%. Press the ‘Menu’
button to conrm your selection and return to the menu. Press and hold
the menu button to return to the standby screen or wait a few seconds
and your Skyway will return to the standby screen automatically.
Highway Smart Mute
Use this setting to determine at what speed Skyway pro
duces audible radar alerts when in Highway mode. When
in Highway mode, Skyway will only produce a visual radar
alert until you exceed the speed limit set within this feature.
Enter the settings menu by pressing and holding the ‘Menu’ button.
Scroll left or right, using the ‘Mute’ or ‘City’ buttons, until you highlight
the feature graphic above and press the ‘Menu’ button to select it. Use

16 17
the ‘Mute’ or ‘City’ buttons to select the speed level you require and
press the ‘Menu’ button to conrm your selection and return to the
menu. Press and hold the menu button to return to the standby screen
or wait a few seconds and your Skyway will return to the standby
screen automatically.
City Smart Mute
Use this setting to determine at what speed Skyway
produces audible radar alerts when in City mode. When
in City mode, Skyway will only produce a visual radar alert
until you exceed the speed limit set within this feature.
Enter the settings menu by pressing and holding the ‘Menu’ button.
Scroll left or right, using the ‘Mute’ or ‘City’ buttons, until you highlight
the feature graphic above and press the ‘Menu’ button to select it. Use
the ‘Mute’ or ‘City’ buttons to select the speed level you require and
press the ‘Menu’ button to conrm your selection and return to the
menu. Press and hold the menu button to return to the standby screen
or wait a few seconds and your Skyway will return to the standby
screen automatically.
Smart Mute GPS speed trap alerts
Use this setting to determine at what speed Skyway
produces audible GPS speed trap alerts. Skyway will only
produce a visual speed trap alert alert until you exceed the
speed limit set within this feature.
Enter the settings menu by pressing and holding the ‘Menu’ button.
Scroll left or right, using the ‘Mute’ or ‘City’ buttons, until you highlight
the feature graphic above and press the ‘Menu’ button to select it. Use
the ‘Mute’ or ‘City’ buttons to select the speed level you require and
press the ‘Menu’ button to conrm your selection and return to the
menu. Press and hold the menu button to return to the standby screen
or wait a few seconds and your Skyway will return to the standby
screen automatically.

17
Select preferred speed unit
Use this feature to switch between MPH and KMH.
Enter the settings menu by pressing and holding the ‘Menu’ button.
Scroll left or right, using the ‘Mute’ or ‘City’ buttons, until you highlight
the feature graphic above and press the ‘Menu’ button to select it. Use
the ‘Mute’ or ‘City’ buttons to choose between MPH and KMH and
press the ‘Menu’ button to conrm your selection and return to the
menu. Press and hold the menu button to return to the standby screen
or wait a few seconds and your Skyway will return to the standby
screen automatically.
Overspeed alert
Use this setting to receive an alert if you exceed
the speed limit selected.
Enter the settings menu by pressing and holding the ‘Menu’ button.
Scroll left or right, using the ‘Mute’ or ‘City’ buttons, until you highlight
the feature graphic above and press the ‘Menu’ button to select it. Use
the ‘Mute’ or ‘City’ buttons to choose your preferred speed limit. For
example, if you select 70mph, Skyway will alert any time you exceed
70mph. Press the ‘Menu’ button to conrm your selection and return
to the menu. Press and hold the menu button to return to the standby
screen or wait a few seconds and your Skyway will return to the
standby screen automatically.
GMT time zone setting
Use this feature to adjust the GPS clock to show the
correct time in your particular time zone. You can also use
this setting to adjust the GPS clock so that it displays the
correct time during summer and DST (Daylight Saving Time).
Enter the settings menu by pressing and holding the ‘Menu’ button.
Scroll left or right, using the ‘Mute’ or ‘City’ buttons, until you highlight
the feature graphic above and press the ‘Menu’ button to select it. Use
the ‘Mute’ or ‘City’ buttons to increase or decrease the time in 1 hour

18 19
increments and press the ‘Menu’ button to conrm your selection and
return to the menu. Press and hold the menu button to return to the
standby screen or wait a few seconds and your Skyway will return to
the standby screen automatically.
GPS speed calibration
Use this feature to adjust the GPS speed displayed on
your Skyway so that it matches the speed displayed on
your vehicle’s speedometer if required.
Enter the settings menu by pressing and holding the ‘Menu’ button.
Scroll left or right, using the ‘Mute’ or ‘City’ buttons, until you highlight
the feature graphic above and press the ‘Menu’ button to select it. Use
the ‘Mute’ or ‘City’ buttons to increase or decrease the speed in 1mph
increments and press the ‘Menu’ button to conrm your selection and
return to the menu. Press and hold the menu button to return to the
standby screen or wait a few seconds and your Skyway will return to
the standby screen automatically.
Current location
Use this feature to display your current
GPS coordinates.
Enter the settings menu by pressing and holding the ‘Menu’ button.
Scroll left or right, using the ‘Mute’ or ‘City’ buttons, until you highlight
the feature graphic above and press the ‘Menu’ button to select it.
The GPS coordinates of your current location will be displayed on the
screen. Press and hold the menu button to return to the standby screen
or wait a few seconds and your Skyway will return to the standby
screen automatically.

19
GPS and Radar/Laser speed trap alert screens explained
Speed trap alert for xed roadside speed traps such as HADECs 3
Smart Motorway cameras, Gatso cameras and Truvelo cameras.
GPS - connected
Speed limit (Background
switches to white if you
are exceeding the limit)
Driving mode
selected (Smart mode)
Distance to speed trap Your speedFixed speed trap such as a
Gatso or Truvelo camera ahead
Red light camera alert
Driving mode
selected (Smart mode) GPS - connected
Distance to camera Your speedRed light camera detected
As there is no speed
limit associated with
a red-light camera a
general warning sign is
displayed instead

20 21
Driving mode
selected (City 1) GPS - connected
Your speed
SPECs Average speed
camera detected
Speed limit
(Background switches
to white if you are
exceeding the limit)
SPECs average speed camera
– alert start
Distance to 1st camera
in the sequence
SPECs average speed camera – mid alert
Your current speed
SPECs Average speed
camera detected
Your average speed
Driving mode
selected (City 1) GPS - connected
Speed limit
(Background switches
to white if you are
exceeding the limit)