AHA smart PASS ASP-2000 User manual

•Before using the product, please read this manual carefully and keep it for later.
•Image drawings and notations in this document may slightly differ from the actual product.
•The contents of this document are subject to change without notice.
English
User’s Manual
Non-contact temperature measurement & facial recognition
for access control system
Copyright ©2020 AHA INC CO.,LTD. All Rights Reserved
www.ahatouch.com
Rev.1.0
⚫Model : ASP-2000
⚫Stand Assembly Manual

1. Smart Pass Overview.………………………………………………………………………………..…...………...
1.1 Smart Pass Introduction..…………………………..……………………………..…...………...….
2. How to use Smart Pass...………………………………………………………………………………………….
2.1 How to run Smart Pass.……………………………………………………………………..............
2.2 How to use Smart Pass.……………………………………………………………………..............
3. Smart Pass screen description………………..……………………………………………............………...
3.1 Initial screen...………………………………………………………………………………………..……..
3.2 Main menu..………………………………….……………………………..……………………………….
3.3 Setting……………...…………………………………………………………….......................................
3.4 Registration of access information …………….……………….……………………………..
3.5 Device information………………………………………………………………………………………..
3.6 Access record……………….……………………………….……………………………………………...
3.7 List of registrants …………………………..…………………………………...................................
4. Countermeasure………………………………………………………………………………..................................
5. Product specification.…………………………………………………………..………….…………………........
6. Product diagram…………………………………………………………………….……………..………………….
7. Product description ………..…………….…………………………………………………………………….
8. Connectivity description….......................…..……………………………………………………………..……….
9. Precautions for use and storage management..………………………………………………….
10. Assemble adjustable floor stand ………………………………………………………………..…….
11. Assemble floor stand ………………………………..……………………………………….…………..…….
12. Assemble table stand …..……………………………………………………………………………..…….
2
2
2
2
3
5
5
5
7
18
19
20
21
22
24
25
26
27
28
29
32
33
Contents

1. Smart Pass Overview
1.1 Smart Pass Introduction
Smart Pass is an advanced AI (Artificial Intelligence) face recognition and heat
Check access control system that accurately identifies a person and measures
temperature even if the mask covers part of the face or wears glasses and
a mask at the same time with advanced deep learning technology.
2. How to use Smart Pass
2.1 How to run Smart Pass
1) Fully understand how to use it through the user’s manual
2) Connect the power adapter and DC power line to check if it works properly.
3) Check if there is any foreign object in the sensor area.
4) Do not install in a place where there is direct sunlight or objects related to
heating devices such as light bulbs.
5) It is recommended to use between 15 ℃ and 30 ℃.
6) How to turn on the device
When connected with the power adapter and DC power line, Smart Pass starts
to work.
The body temperature measurement program is automatically executed
without running a separate program. -> It is recommended that you wait for
30 minutes before using the Android operating system and the temperature
measurement program to detect the ambient temperature in the stabilization
stage.
2

< How to measure accurately >
If the forehead is placed on the
red dot on the screen, the body
temperature is measured
accurately
(measured distance is 30cm).
If the forehead is not placed on
the red dot on the screen,
accurate measurement will not
be possible.
If the forehead is not placed on
the red dot on the screen,
accurate measurement will not
be possible.
2.2 How to use Smart Pass
-The measuring distance should be measured at 30cm.
-The measuring range is 34℃ ~ 42℃.
-When measuring body temperature, do not cover the main measurement areas
(forehead, eyes, face) with clothes or other means.
-If the body heats up due to physical activity, wait for the body heat to return to
the state in which there was no physical activity after a certain period of time
before measuring.
-When measuring body temperature, do not move for a certain period of time
(more than 2 seconds).
-If the face is aligned with the red dot on the screen, the body temperature is
measured and the body temperature is displayed.
-When body temperature exceeds 42℃, it is displayed as HIGH, and when body
temperature is below 34℃, it is displayed as LOW.
XX O
3

< Screen display after measurement>
At normal body temperature
(Below the warning set value)
Body temperature is displayed
on a green background
At high body temperature
(Over warning setting value)
Body temperature is displayed
on a red background
Wrong wearing a mask
On a red background
'Please wear a mask' indication
Not wearing a mask
On a red background
'Please wear a mask' indication
4

3. Smart Pass screen description
3.1 Initial screen
This is a screen for face recognition and temperature measurement.
The current date & time are displayed at the top. When a person is detected,
contextual phrases or temperature measurement results are displayed.
Depending on the setting, information such as IP, company name, and version
may be displayed at the bottom of the screen.
3.2 Main menu
When the mouse is connected and the wheel button is pressed, the password
input window appears, and when the correct password is entered, the main
menu is displayed on the screen. ※ The initial password is '123456'.
5

No. Name Description
1 Status information The set device name, IP, user name, and login
status are displayed.
2 Log In Management Used to connect the device to a network
(not currently supported)
3 Application settings Open the Smart Pass detailed settings menu.
4 Face registration Capture a person's face and register it in
the database.
5 Application information Check various information of the device.
6 Pass record Displays a list of people who have measured the
temperature.
7 Face database Shows a list of people registered in the database.
1
2
3
6
4
5
7
6

3.3 Setting
This is a detailed menu for setting up a Smart Pass.
(1) Name setting
Set the device name and
company name.
No. Name Description
1
Device
name setting
You
can set the device name and company name.
2
Detailed
setting menu
This is a detailed setting menu related to face recognition and
body temperature measurement functions.
3
Detailed
recognition
setting
This menu allows you to set detailed face recognition sensitivity,
comparison count, and biometric detection.
4
Volume
setting
You
can set the sound volume.
5
Startup
setting
You
can set the program startup when starting the device.
6
Registration information
display
setting
You
can set the information view displayed at the bottom of
the
initial
screen.
7
Recognition
result
setting
You
can set the face recognition result.
8
Password
setting
You
can change the password.
9
Screen
resolution
setting
You
can change the camera screen resolution.
10
Screen saver
brightness setting
You
can set the brightness in screen saver mode.
11
Timer
setting
You
can set the function to restart or shut down the device at a
set
time on a24-hour basis.
12
Relay
setting
This
is the setting when using the relay function in conjunction
with
the door.
13
Others
Firmware
upgrades or server communication can be established.
14
Program
initialization
This
is the function to initialize the program.
11
10
1
2
3
4
5
6
7
8
9
12
13
14
7

11
10
(2) Inspection setting
This is a detailed setting menu related to face recognition and temperature
measurement.
No.
Name Description
1Temperature
Test Turns the temperature test function on or off.
2Temperature
Compensation
It is used to calibrate the temperature when measured different from
the actual temperature by the external temperature. In case of manual
setting, detailed input field appears. Input value is between 0 ~ 1 ℃.
3 Scene selection Setting whether the device is installed indoors or outdoors.
4Measuring
Method
You can choose a fast scan or a precise scan. You can increase the
face recognition rate when setting up a precise scan.
5Alarm threshold
If the measured temperature is higher than the entered value, an
alarm message is displayed. When the temperature alarm is on,
a beep sounds.
6Temperature
Alarm Enable or disable the Alarm.
7Temperature
Display
Change the temperature display format to Celsius (℃) or
Fahrenheit (℉).
8 Fan It set the operation of the fan for heat dissipation.
9 Mask detection
Measure your temperature and check whether wear a mask or not.
When a person without a mask is detected, display a no-access sign
and you can hear the voice.
10 Stranger mode When it detects a person who is not registered in the database,
it notifies them that it is a stranger.
11 Stranger record When a stranger is detected, the captured picture is saved separately.
1
2
3
4
5
6
7
8
9
8

(3) Detailed recognition setting
When checking whether it is a stranger or registered in the database, the
accuracy and the number of identifications are set.
1
2
3
No. Name Description
1Test threshold
Determines the precision of comparison with
photos in the database. The lower the number,
the more precise the comparison. Input value is
10 ~ 20.
2Comparison count
Compare and check the number of times
entered.
The bigger the number of comparisons, the
more accurately a person can be judged. Up to
0~99 can be entered.
3
Facial Liveness
Detection(Face
Biometric
Authentication)
This is to detect if a person in front of camera is
a real person or manipulated image (photo) and
stop spoofing attempts.
9

(4) Volume setting
Adjust the volume level for voice guidance and warning sounds.
(5) Startup setting
Change the behavior or program settings when the device is turned on.
No. Name Description
1 Auto start Set whether the app turns on automatically when the
device is turned on.
2Application
daemon
When the setting is on, the app will automatically
appear on the screen after 30 seconds even if the app
is not on the screen.
3
Application
thread
daemon
If the setting is on, the camera function will restart if
an error occurs while the camera is on.
1
2
3
10

(6) Application information settings
Set whether to display information such as MAC address, IP, and company
name on the initial screen.
< Hide / Show app info setting >
11

(7) Recognition effect display
Set the change of screen or light when a person is recognized.
No. Name Description
1Recognition
success
When a person registered in the database is recognized,
a picture of the person is displayed, or the name of the
person is displayed.
2Recognition
failure
Choose whether to turn the light to red when the
person not registered in the database is recognized or
the mask is not worn. If the dimmer setting is a single
light, this setting is not visible.
3Photo flood
lamp
Set whether to use all colors such as
white / red / green
lights or only white light.
12

(8) Password setting
This menu is for changing the password.
※ The default password value is '123456'.
(9) Camera resolution setting
Change the camera captured screen resolution. There are 640 * 480 resolution
and 1280 * 720 resolution.
13

(10) Screen protection brightness setting
Set the screen brightness when the screen is switched to the screen protection
state because no person is detected for a certain period of time.
(11) Restart time setting
Enter the hour in the upper column and the minute in the lower column on
a 24-hour basis. Reboot or shut down the device at the specified time.
14

(12) Relay setting
Set relay mode and delay time
Relay is a kind of switch and operates according to the mode setting as follows.
Relay mode is used to operate the external door lock, warning light, alarm
buzzer, etc. according to the recognition result.
Maximum driving current and voltage: 2A 30VDC, 0.28A 220VAC
Excessive use of the maximum drive current and voltage may cause product
defects.
No. Name Description
1 admittance Relay output when ‘admittance’ judgment is displayed on
the screen(Normal temperature, wearing a mask)
2 No entry Relay output when ‘No entry’ judgment is displayed on the
screen(High temperature or no mask)
3 Mode 0 Disable relay
4 Mode 1
When the relay is open, it is closed for the set ‘delay time’
and Then opened again.
5 Mode 2
The relay is closed and opened for the set ‘delay time’ and
Then closed again
6Delay
time
Set the operation time of the relay.
The initial value is 5 seconds, and the setting is from 0 to
63 Seconds.
15

(13) Others
You can configure firmware upgrade or server communication related settings.
No. Name Description
1 Firmware version
You can manually upgrade the firmware by
connecting the USB containing the firmware upgrade
file. The file name should be ‘updateTemp.bin’ and it
should be at the top of the USB path.
2 Callback setting If you select On, a field for entering content appears.
Enter if callback setting is required.
3Communication
address setting
If you select On, a field for entering content appears.
Enter the IP and port number of the server to
communicate with. The format is IP: PORT
16

(14) Program initialization
This function returns the program settings to the initial state.
When the button is pressed, the above warning appears, and when the OK button is
pressed, various settings are initialized and all information and records registered in
the database are lost.
※ Once the program initialization function is activated, it cannot be reversed.
※ Back up data before initialization.
17

3.4 Registration of access information
This is a function to take a person and register it in the face database.
Press the Gather button at the top to take a picture. The picture which was
taken is scaled to fit the person's face. Enter ID and name, select gender and
click Save to save it to the Face database.
No. Item Description
1 Photo shoot
When
a face is properly in the screen for registration,
press
the take Photo button to take a picture to save.
2 Employee ID
You
can enter the employee ID (Employee number).
3 Name
Enter
your name.
4 Gender
Select
your gender.
18

3.5 Device information
Displays information about apps and devices. Information such as firmware
version, memory, brightness, and volume is displayed.
19